体现裕度定制思想的轴流压气机二维特性预估方法

为实施裕度定制，本文开发了能够体现裕度定制思想的轴流压气机二维特性预估方法。精细考虑了前后缘形状、最大弯度位置等，尤其是通过考虑叶片力而全面包含掠影响是本方法的重要特色。为初步验证本方法，对NASA37和NASA67转子进行了性能预估并与试验结果进行了对比。结果表明，本方法基本可靠，可以用于裕度定制目的。     

基于图像识别的发动机内窥智能检测系统研究

介绍了一种基于图像识别技术的航空发动机内窥检测的新方法，采用最大类间方差法计算二值化分割的最佳阈值，并将提取的图像特征输入神经网络进行分层识别，最后由专家系统对损伤程度进行了诊断。通过现场测试，证明了该方法的有效性和实用性．     

钛合金表面镍包石墨喷涂层的耐磨性能

为了提高钛合金的表面耐磨性,利用氧乙炔热喷涂枪,在TC4合金表面上制备出镍包石墨涂层。采用MXP-2000型销盘式摩擦磨损实验机,进行钛合金及其镍包石墨涂层的干摩擦磨损实验,并利用扫描电镜对磨损表面进行观察和分析。实验结果发现,镍包石墨涂层的摩擦系数只有钛合金的一半左右,前者磨损量为后者的1/6,说明镍包石墨涂层可以大大提高钛合金的表面耐磨性能。TC4合金的磨损机制以黏着磨损为主,喷涂层的磨损机制以磨粒磨损为主,喷涂层中的石墨润滑相是其耐磨性高的主要原因。     

空载固体发动机计算与试验模态相关性分析

为了预测空载状态固体火箭发动机动态特性,对其进行了模态试验,并应用MSC.Marc进行了模态计算,然后对比两者的结果,进行了相关性分析和评估。计算得到了发动机250Hz以内的一阶弯曲模态和五阶呼吸模态。试验测得了发动机的三阶呼吸模态和一阶弯曲模态。比较试验测试模态和与之对应的计算模态:固有频率相对误差均在5%以内;振型相关图上的点大都分布在斜率为1(或 1)的直线周围;MAC(模态置信判据)值在0 9左右。说明计算与试验模态有较好的相关性,有限元计算模型比较准确的反映了实际情况。     

连续自由流电泳微重力下分离模式蛋白质的研究

以连续自由流电泳的区带电泳模式分离血红蛋白和细胞色素C，比较了不同缓冲液甘油浓度下的分离效果，确定了最终装载在神舟4号飞船上A3—2型电泳仪的电泳分离条件，通过地面和空间实验，初步探讨了微重力对连续自由流电泳分离的影响，并对电泳的分离产物做了多种检测．     

An innovative study on low surface energy micronano coatings with multilevel structures for laminar flow design

Laminar flow design is one of the most effective ways to reduce the drag of a commercial aircraft by expanding the laminar flow region on the surface of the aircraft. As material science develops, the emergence of new materials such as low surface energy materials has offered new choices for laminar flow design of commercial aircraft. Different types of low surface energy micro-nano coatings are prepared to verify the effects on the boundary layer transition position and the drag of the airfoil through wind tunnel tests. The infrared thermal imaging technology is adopted for measuring the boundary layer transition, while the momentum integral approach is employed to measure the drag coefficient through a wake rake. Infrared thermal imaging results indicate that the coatings are capable of moving backward the boundary layer transition position at both a low velocity of Mach number 0.15 and a high velocity of Mach number 0.785. Results of the momentum integral approach demonstrate that the drag coefficients are reduced obviously within the cruising angle of attack range from 1° and 5° by introducing the low surface energy micro-nano coating technology.     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

温度对飞机燃油射流泵工作特性影响

建立了射流泵数学模型,采用数值计算方法对其工作特性进行了模拟,搭建了实验台,采用RP-3燃油,通过实验数据验证了模型的正确性.在此基础上,分别选择了RP-3和JET-A两种燃油,计算了从-40℃~40℃温度下,不同操作压力对射流泵流量比的影响.结果表明:燃油温度高于0℃时,温度对射流泵工作特性影响并不明显,随着温度的降低,射流泵性能与标准温度下（20℃）偏差越来越大,且压比越高此偏差越明显.当温度高于0℃时,采用RP-3和JET-A燃油性能相差不大,RP-3燃油性能略优于JET-A燃油,但是在低温下,RP-3燃油性能远高于JET-A燃油.因此当燃油温度较低且压比较高时,必须充分考虑温度对射流泵特性的影响.      

10cm氙离子推力器变推力特性研究

非重力阻尼的连续、快速、高精度补偿是实现重力梯度测量卫星精细重力场测量的关键技术之一,直接影响到整星工程任务的成败。针对重力梯度测量卫星在轨飞行期间对电推进系统宽范围连续变推力能力的应用需求,分析了10cm氙离子推力器推力调节响应特性。在此基础上,通过对阳极电流、励磁电流和阳极流率等推力高敏感响应参量的组合调节,开展了推力调节试验研究,验证了10cm氙离子推力器宽范围连续变推力调节能力,获得了1～20mN范围内的推力调节性能及其变化规律。试验结果表明：在采用地面供电、供气设备条件下,10cm氙离子推力器能够在100～597W的功率范围内实现0.98～20.29mN的推力宽范围调节,比冲175～3500s,推力分辨率优于50μN。研究为建立10cm氙离子电推进系统的推力控制数学模型及调节控制算法奠定基础。