数字闭环光纤陀螺的调制串扰误差

 通过分析数字闭环光纤陀螺的阶梯波调制信号与输出死区、周期噪声干扰及小角速度漂移的关系,提出了调制串扰误差的概念。指出调制信号与探测器输出信号之间的电交叉耦合及调制信号产生的调制误差是产生调制串扰误差的干扰源。将调制串扰通道模型简化为比例环节和部分积分环节,并和光纤陀螺理想模型结合,建立了光纤陀螺调制串扰误差模型,利用该模型推导出了产生死区的条件及周期噪声干扰和小角速度漂移造成的输出偏差表达式,并对周期噪声的幅值、频率与陀螺输出量级、带宽之间的关系进行了定量分析。调制串扰误差的仿真和实验结果与理论分析结果基本一致,验证了调制串扰误差模型的正确性。     

Flight Flutter Modal Parameters Identification with Atmospheric Turbulence Excitation Based on Wavelet Transformation

针对基于大气紊流激励的飞机颤振试验数据具有信噪比低以及测量数据以加速度响应形式给出等特点,将小波变换与随机减量法相结合对飞机颤振模态参数进行识别,首先利用随机减量法获得结构在非零初始加速度条件下的自由衰减响应,然后对该自由衰减响应进行Morlet连续小波变换,为使变换简单,本文采用了Parseval定理和留数定理,利用Morlet的带通滤波特性,通过搜索小波变换系数在不同的尺度区域内的极大值,再根据小波变换系数的极大值、相角与固有振动频率及阻尼系数间的关系,即可识别出各模态参数。并对利用小波变换识别颤振模态参数时,实现模态解耦应满足的条件进行了分析研究。通过仿真和飞机颤振试验数据分析,验证了该识别方法不仅简单、有效和可行,而且具有较强的抗噪性。     

Investigation on the Thermal Conductivity of 3-Dimensional and 4-Directional Braided Composites

It is vital to choose a factual and reasonable micro-structural model of braided composites for improving the calculating precision of thermal property of 3-D braided composites by finite element method (FEM). On the basis of new microstructure model of braided composites proposed recently, the model of FEM calculation for thermal conductivity of 3-dimennsional and 4-directional braided composites is set up in this paper. The curves of coefficient of effective thermal conductivity versus fiber volume ratio and interior braiding angle are obtained. Furthermore, comparing the results of FEM with the available experimental data,the reasonability and veracity of calculation are confirmed at the same time.     

Periodic Error Compensation for Quartz MEMS Gyroscope Drift of INS

In order to improve the navigation accuracy of an inertial navigation system （INS）, composed of quartz gyroscopes, the existing real-time compensation methods for periodic errors in quartz gyroscope drift and the periodic error term relationship between sampled original data and smoothed data are reviewed. On the base of the results, a new compensation method called using former period characteristics to compensate latter smoothness data （UFCL for short） method is proposed considering the INS working characteristics. This new method uses the original data without smoothing to work out an error conversion formula at the INS initial alignment time and then compensate the smoothed data errors by way of the formula at the navigation time. Both theoretical analysis and experimental results demonstrate that this method is able to cut down on computational time and raise the accuracy which makes it a better real-time compensation approach for periodic error terms of quartz micro electronic mechanical system （MEMS） gyroscope＇s zero drift.     

基于牛顿欧拉法的3-RPS并联机构逆动力学分析

 以3-RPS机构为例,研究了对称少自由度并联机构的逆动力学问题。因其自由度数目小于6,该类机构的支链不仅传递驱动力,同时还需为动平台提供约束。然而,现有文献大多未对广义约束力给予足够的重视。采用牛顿欧拉法建立了3-RPS机构的刚体动力学方程,给定动平台的运动规律及外载荷后,可一并求解机构所需的驱动力与约束力矩。算例仿真表明,与动平台自由速度方向不一致的外载荷主要需由约束力矩平衡。因此,在对称少自由度并联机构动力学设计中,必须计入广义约束力的影响。     

某型飞机前起落架收放作动筒耳环螺栓断裂故障分析

从断口理化分析、故障件检查、静强度、压杆失稳、出现裂纹后的剩余强度以及特殊受载情况等方面对耳环螺栓断裂故障进行了综合分析,找出了耳环螺栓断裂的原因。     

Scientific objectives and payloads of Tianwen-1, China’s first Mars exploration mission

This paper describes the scientific objectives and payloads of Tianwen-1, China’s first exploration mission to Mars. An orbiter, carrying a lander and a rover, lifted-off in July 2020 for a journey to Mars where it should arrive in February 2021. A suite of 13 scientific payloads, for in-situ and remote sensing, autonomously commanded by integrated payload controllers and mounted on the orbiter and the rover will study the magnetosphere and ionosphere of Mars and the relation with the solar wind, the atmosphere, surface and subsurface of the planet, looking at the topography, composition and structure and in particular for subsurface ice. The mission will also investigate Mars climate history. It is expected that Tianwen-1 will contribute significantly to advance our scientific knowledge of Mars.     

专访丹麦王国驻上海总领事馆总领事何丽兰女士

问:2010上海世博会是全球关注的一大盛事。阁下对明年的上海世博会有什么感言?答:我作为筹办方和世博会的组织成员,正好及时抵达上海,我很激动。我对我们的展馆和在馆内及周围举行活动制定的所有计划的进展有点担心。我们非常幸运地受到许多媒体的注意,支持设计师们将原型"小美人鱼"带到我们展馆的想法。这有助于保持我们团队高涨的情绪,并在中国和丹麦都得到了支持。问:2010上海世博会是全球关注的一大盛事,阁下对明年的上海世博会有什么感言?     

虚拟装配技术的研究与应用现状

虚拟装配将从根本上改变传统的产品设计和制造模式,在实际生产之前,首先在虚拟制造环境中完成虚拟产品原型代替实际产品进行试验,对其性能和可装配性等进行评价,从而达到整个产品全局最优,缩短产品设计与制造周期,降低产品开发成本,提高产品快速响应市场变化的能力.     

两种质量多元诊断理论(英文)

工厂中,多工序、多指标系统是常见的。在该系统中推行质量控制与诊断必须考虑下列两点：上工序对下工序的影响以及指标间的相关性。由于这两点是同时存在的,使得问题更加复杂。我们需要应用张公绪教授在１９９６年提出的两种质量多元诊断理论来解决此复杂问题。本文介绍了其基本原理和具体应用,实际应用结果与理论是一致的。