国家标准局新的时间、频率服务

一、引言 1983年国家标准局(NBS)建立了两项新的时间和频率服务。这两项服务的建立使得用户能比以前更精确地、更不费力地得到溯源于NBS的时间和频率。这些新的服务可以为那些要求时间传递精度在3毫微秒到1微秒范围内的或要求频率校准性能在10~(-11)到10~(-14)范围内的用户服务。然而,有许多不需要这么高精度的应用,用户也能从这些服务得到好处,这是因为其自动化程度高,使用简单、并有NBS的帮助。     

溅镀C轴倾斜的压电膜和切变波谐振器

作者对溅镀的压电膜能否应用于甚高频至微波频率的声波器件进行了研究。本文介绍了切变波谐振器用的C轴倾斜的氧化锌(ZnO)和氮化铝(AlN)膜的生长及特性。文中计算了某些膜的切变波激动的定向关系。这些膜在C轴取向与表面法线成大约45°时,可能激励出接近于纯的切变波。在其他角度,则只能激励准切变波和准纵向波。 C轴对膜法线倾斜方向合适的ZnO或AlN膜,是在配有辅助阳极的反应式直流面磁控管溅镀系统中生长的。这类膜可用扫描式电子显微镜(SEM)和体声波器件测量法进行鉴定。自Si基片法线倾斜的C轴晶粒柱形结构可在扫描式电子显微镜中清楚地看到。C轴倾斜角达45°,厚度达10微米的薄膜已经制做成功。在P~+Si基片上溅镀上ZnO和AlN可以制成复合谐振器。这类谐振器的Q值在200兆赫到500兆赫基频谐振范围内大约为5000。特别令人感兴趣的是可以对谐振频率进行温度补偿。在ZnO/Si和AlN/Si的复合结构上已制造出室温下串联谐振频率的绝对温度系数小于1×10~6/℃的谐振器。ZnO和AlN晶片谐振器的温度系数已测出为-36.2×10~-6/℃和-25×10~-6/℃。这表明P~+Si基片在切变膜时的温度系数大约是+9×10~6/℃、     

晶体谐振器—振荡器测试设备及测试结果

一、引言美国陆军电子技术及器件实验室(ETDL)的频率控制与计时分部的主要任务是要提高晶体谐振器与振荡器工艺水平,以满足军队用户的要求。第二个任务是向计划管理人员、系统设计人员提供谘询并维持晶体谐振器与振荡器的军用技术指标(也就是MIL-C-3098和MIL-0-55310)。这些任务要求对晶体谐振器和振荡器的工艺水平有详细而实际的了解。本文的目的是概述本实验室的技术力量,介绍一些研究结果,并在需要时向国防部所属用户提供晶体振荡器的测试、选择、技术指标和研制方面的帮助。     

Operating characteristics of a high radius pre-swirl cooling system

An experimental investigation into pre-swirl effectiveness and receiver hole discharge coefficient characteristics for a high radius injection pre-swirl cooling systems was carried out on a physically representative experimental rig with a 450 mm diameter rotor.The receiver holes and pre-swirl nozzle were located at a radius of 181 mm and 180 mm respectively.The experimental work was mainly conducted at 5 000～12 000 r/min,4 bar absolute pressure and 1.132 kg/s air supply.The maximum air supply temperature was 190 ℃.Pressure and temperature distributions in the pre-swirl system were examined with an emphasis on the velocity effectiveness of the pre-swirl system as a whole and on the discharge coefficients of the rotating 'receiver holes' in the rotor.The results showed that the velocity effectiveness increased with increasing swirl ratio resulting in reduced blade cooling flow temperature.Different seal flow configurations caused very different effectiveness at different speeds,but outflow through the inner and outer seals always gave the highest effectiveness compared other configurations.Increasing the seal flow rate reduced the effectiveness.For the coefficient of discharge,except for the low speed range,it increased with increase in swirl ratio for most speeds.      

STUDY ON THE SOLUTION OF DYNAMIC THERMOELASTICITY SYSTEM

ＳＴＵＤＹＯＮＴＨＥＳＯＬＵＴＩＯＮＯＦＤＹＮＡＭＩＣＴＨＥＲＭＯＥＬＡＳＴＩＣＩＴＹＳＹＳＴＥＭＧｅｎｇＺｈｅｎｗｅｎ（ＢａｓｉｃＤｅｐａｒｔｍｅｎｔ，ＺｈｏｎｇｚｈｏｕＵｎｉｖｅｒｓｉｔｙ５２Ｈａｎｇｈａｉｚｈｏｎｇｌｕ，Ｚｈｅｎｇｚｈｏｕ４５０...     

A PARALLEL IMAGINARY EBE METHOD FOR SOLVING POSITIVE DEFINITE LINEAR SYSTEMS

ＡＰＡＲＡＬＬＥＬＩＭＡＧＩＮＡＲＹＥＢＥＭＥＴＨＯＤＦＯＲＳＯＬＶＩＮＧＰＯＳＩＴＩＶＥＤＥＦＩＮＩＴＥＬＩＮＥＡＲＳＹＳＴＥＭＳＰａｎＸｉａｏｓｕ（ＤｅｐａｒｔｍｅｎｔｏｆＡｐｐｌｉｅｄＭａｔｈｅｍａｔｉｃｓ，ＰｈｙｓｉｃｓａｎｄＭｅｃｈａｎｉｓ...     

ELECTRONIC CONTROL OF TURBINE POWER UNITS

ＥＬＥＣＴＲＯＮＩＣＣＯＮＴＲＯＬＯＦＴＵＲＢＩＮＥＰＯＷＥＲＵＮＩＴＳ￥ＷａｎｇＤａｏｂｏ（ＤｅｐａｒｔｍｅｎｔｏｆＳｃｉｅｎｃｅａｎｄＴｅｃｈｎｏｌｏｇｙ，ＮＵＡＡ２９ＹｕｄａｏＳｔｒｅｅｔ，Ｎａｎｊｉｎｇ２１００１６，Ｐ．Ｒ．Ｃｈｉｎａ）Ａｂｓ...     

DATA PROCESSING ON LINEARIZATION OF HOT-WIRE ANEMOMETER

ＤＡＴＡＰＲＯＣＥＳＳＩＮＧＯＮＬＩＮＥＡＲＩＺＡＴＩＯＮＯＦＨＯＴ－ＷＩＲＥＡＮＥＭＯＭＥＴＥＲ￥ＬｉＳｕｆｅｎ（ＤｅｐａｒｔｍｅｎｔｏｆＰｏｗｅｒＥｎｇｉｎｅｅｒｉｎｇ，ＮＵＡＡ２９ＹｕｄａｏＳｔｒｅｅｔ，Ｎａｎｊｉｎｇ２１００１６，Ｐ．Ｒ．Ｃｈ...     

A NEW EXPRESSION OF FATIGUE SIZE FACTOR

ＡＮＥＷＥＸＰＲＥＳＳＩＯＮＯＦＦＡＴＩＧＵＥＳＩＺＥＦＡＣＴＯＲ￥ＹａｏＷｅｉｘｉｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＡｉｒｃｒａｆｔＥｎｇｉｎｅｅｒｉｎｇ，ＮＵＡＡ２９ＹｕｄａｏＳｔｒｅｅｔ，Ｎａｎｊｉｎｇ２１００１６，Ｐ．Ｒ．Ｃｈｉｎａ）Ａｂｓｔｒａ...     

CONSTRUCTIONOFACLASSOFPNSEQUENCESWITHPRIMENUMBERPERIODSOF4t＋1FORM

构造了一类４ｔ＋１型质数周期的伪随机序列。该序列提供了比ｍ（Ｍ）序列更多的可供选择周期数，同时证明了它具有良好的伪随机特性