某航天器输氢管道系统结构完整性评估

为保障某航天器在服役年限内不发生事故,针对航天器上采用插入焊接技术的精密管道系统进行结构完整性评估。在考虑到系统存在整圈的环形未焊透缺陷基础上,结合工程实践,假设在焊接区域存在更危险的平面缺陷。首先,开展高压气相热充氢试验下的标准拉伸和三点弯试验得到管道系统材料"J-75"在临氢环境下应力应变曲线和断裂韧性。其次,采用有限元程序计算系统在内压、惯性载荷与离面位移作用下的应力分布,考虑到间隙配合中的不确定性,改变模型中的最大间隙多次模拟计算,发现最大应力位置基本不变,以此区域作为假想缺陷的具体萌生区域。最后,采用失效评估图（FAD）方法对存在4种缺陷模式的系统分别进行结构完整性评估。通过引入安全裕度的概念,发现系统在含有初始尺寸（0.15 mm）的4种平面缺陷时,均处于安全状态,并且安全裕度都在2倍以上;通过工程临界分析（ECA）发现随着缺陷尺寸的增大,系统中含有缺陷2（位于管道焊接区域最大应力处的轴对称平面且沿焊深方向扩展的缺陷）时最为危险,且当缺陷深度超过0.61 mm时将断裂失效;考虑到测试数据的弥散性,针对系统最危险的模式,以安全裕度为可靠性指标,将失效评估图方法与可靠性评价相结合,得到系统在含有尺寸为0.15 mm的缺陷2情况下保有足够安全裕度的可靠性下限值超过0.999 5。     

基于改进粒子群优化模糊控制的MPPT算法研究

在光照强度和温度变化时,常规的最大功率点跟踪(MPPT)算法难以快速准确地跟踪光伏系统最大功率点。针对此问题,设计了一种改进粒子群优化算法(PSO)的模糊控制器。首先,依据常规MPPT特性,设计了一种带调整因子的模糊控制算法以快速收敛到最大功率点;然后,采用参数自适应PSO对设计的模糊控制器调整因子进行动态优化。仿真结果表明:所设计的参数自适应PSO优化模糊控制器能快速准确地跟踪最大功率点,保证了MPPT的动态响应速度和稳态精度,提高了光伏系统的工作效率。     

基于定子电阻自适应辨识的感应电机死区补偿

电压源型逆变器由于死区效应,导致输出发生非标准化、畸变化,影响感应电机的控制精确度,特别是无速度传感器矢量控制,同时造成电网侧能量的流失。为了减小死区效应产生的影响,列出误差计算公式,求得总延时时间。另外,对定子电阻进行自适应辨识,增加所求延时时间精确度的同时可以运用到电机矢量控制中。经过补偿误差电压,提高了控制性能,降低了对控制系统的影响。结果表明所提补偿策略对电流波形、总谐波失真具有改善作用。     

Hypervelocity impact induced shock acoustic emission waves for quantitative damage evaluation using in situ miniaturized piezoelectric sensor network

Manmade debris and natural meteoroids, travelling in the Low Earth Orbit at a speed of several kilometers per second, pose a severe safety concern to the spacecraft in service through the HyperVelocity Impact(HVI). To address this issue, an investigation of shock Acoustic Emission(AE) waves induced by HVI to a downscaled two-layer Whipple shielding structure is performed,to realize a quantitative damage evaluation. Firstly a hybrid numerical model integrating smoothparticle hydrodynamics and finite element is built to obtain the wave response. The projectiles, with various impact velocities and directions, are modelled to impact the shielding structure with different thicknesses. Then experimental validation is carried out with built-in miniaturized piezoelectric sensors to in situ sense the HVI-induced AE waves. A quantitative agreement is obtained between numerical and experimental results, demonstrating the correctness of the hybrid model and facilitating the explanation of obtained AE signals in experiment. Based on the understanding of HVI-induced wave components, assessment of the damage severity, i.e., whether the outer shielding layer is perforated or not, is performed using the energy ratio between the regions of ‘‘high frequency" and ‘‘low frequency" in the acquired AE signals. Lastly, the direct-arrival fundamentalsymmetric wave mode is isolated from each sensing signal to be input into an enhanced delay-andsum algorithm, which visualizes HVI spots accurately and instantaneously with different sensor network configuration. All these works demonstrate the potential of quantitative, in situ, and real time HVI monitoring using miniaturized piezoelectric sensor network.     

Behavior and functional modeling methods of doubly salient electromagnetic generators for aircraft electrical power system applications

The Doubly Salient Electromagnetic Generator(DSEG) is a promising candidate in aircraft generator application due to the simplicity, robustness and reliability. However, the field windings and the armature windings are strongly coupled, which makes the inductance characteristics non-linear and too complex to model. The complex model with low precision also leads to difficulties in modeling and analysis of the entire aircraft Electrical Power System(EPS). A behavior level modeling method based on modified inductance Support Vector Machine(SVM) is proposed. The Finite Element Analysis(FEA) inductance data are modified based on the experiment results to improve the precision. A functional level modeling method based on input–output characteristics SVM is also proposed. The two modeling methods are applied to a 9 kW DSEG prototype. The steady state and transient process precision of the proposed methods are proved by comparing with the experiment results. Meanwhile, the modeling time consumption, the application time consumption and the calculation resource demand are compared. The DSEG behavior and functional modeling methods provide precious results with high efficiency, which accelerates theoretical analysis and expands the application foreground of the DSEG in the aircraft EPS.     

基于小波神经网络PID的永磁同步电机转速控制

提出了基于小波神经网络PID的永磁同步电机(PMSM)转速控制策略。根据系统运行参数的变化,采用三层前馈式人工神经网络,基于梯度下降纠正误差法在线训练实时更新PID参数值。采用小波神经网络和增量式PID共同构成转速环控制器。建立PMSM数学模型,设计PMSM速度环控制器,构建S函数,对控制算法进行仿真试验,验证了该控制算法的先进性。试验结果表明,所提控制策略比传统PID转速控制具有更好的动态性能和抗干扰能力。     

低排放燃烧室NO_x排放试验及预测方法研究

为了研究中心分级贫油低排放燃烧室的排放特性和排放预测方法,针对一个低排放头部方案,在单头部燃烧室试验件上,在不同的温度、压力、油气比、供油模式和分级比条件下,测量其排放性能。以Lefebvre排放经验预测公式为基础,采用经验分析方法拟合排放试验数据,归纳出适用于本头部方案的排放预测公式。表征预测好坏的判定系数R2在小工况下和大工况下分别为0.95和0.93,表明预测结果与试验结果符合度较好。小工况和大工况排放特性不同,对仅预燃级喷油的小工况工作模式,NO_x排放主要受化学恰当燃烧温度和预燃级局部当量比的影响;对预燃级和主燃级同时喷油的大工况工作模式,NO_x排放主要受燃烧区温度和主燃级燃油比例的影响。     

纤维复合材料刚度设计的力学原理及其应用

针对航空用纤维复合材料,基于纤维与基体的协调变形规律和材料应变能密度的计算,导出了纤维复合材料的刚度表达式,研究了刚度矩阵的基本力学特性,给出了复合材料刚度矩阵元素与基体材料的刚度、纤维束的刚度及铺设方向的关系,提供了平面铺层和三维取向纤维复合材料的基本刚度设计公式和设计方法。最后给出工程应用设计方法的几个具体例子,并与其他理论和实验结果进行了对比。研究结果表明,在考虑材料制备工艺缺陷造成的刚度折减后,本文提出的设计公式及方法可应用于纤维复合材料的优化设计。     

基于Lamb波相控阵和图像增强方法的损伤监测

利用Lamb波和超声相控阵理论对结构进行损伤监测。选择合适的低频窄带激励信号,产生单一模式Lamb波,结合超声相控阵技术对结构进行多方位监测。针对原始损伤图像不完美的问题,研究基于点运算的对比度增强方法,改善图像质量,提高图像的可识别度和分辨率。在复合材料板结构和铝板结构中针对不同损伤类型的实验研究证明,运用图像增强技术后的损伤图像表征清晰、识别度高。     

基于圆锥向角和相位差变化率的运动单平台无源定位算法和精度分析

 以往的相位差变化率定位技术中需要利用二维相位干涉仪获取方位角和俯仰角信息,出于降低平台载荷负担的需求,考虑到一维相位干涉仪系统仅能获取圆锥向角的性质,针对地面固定目标提出了一种联合利用圆锥向角和相位差变化率的一维干涉仪体制瞬时定位算法,计算和分析了定位误差的几何分布(GDOP),并给出了蒙特卡罗仿真实验结果,并指出了干涉仪安装方向和平台姿态变化的基本原则。研究表明,这样的无源定位系统设备相对简单,但同样具有对目标的定位能力。这些有益结论可以为系统的设计和应用提供理论依据。