长杆弹侵彻新型复合装甲数值仿真及研究

应用有限元计算程序AUTODYN模拟了由爆炸反应装甲和陶瓷复合装甲组成的新型复合装甲在长杆弹斜侵彻作用下的侵彻过程。根据长杆弹与爆炸反应装甲和陶瓷复合装甲的作用现象,研究了长杆弹对新型复合装甲的侵彻机理以及两者在各时刻的作用规律。所得结论对进行其他复合装甲抗长杆弹侵彻的研究具有一定的参考价值。     

飞翼模型高速风洞PIV试验研究

对小展弦比飞翼标模在2.4米跨声速风洞中创新开展了PIV试验。对空风洞进行了测速校核,并对小展弦比飞翼标模开展了二维、三维涡迹PIV测试,试验马赫数为0.4~0.9。测试结果表明,2.4m风洞PIV试验数据具有较高的准确度,M≤0.8时空风洞测速结果与理论值相差不超过1%,M=0.9时相差不超过2%。小展弦比飞翼标模测试结果显示,M数增大使机翼尾涡涡量和切向速度增大,涡核向内展向方向移动。前缘涡与上翼面分离具有密切关系:当M=0.8、α≤12°时,翼梢测试截面的前缘涡尚未破裂,上翼面未发生显著的流动分离;当α≥13°时,前缘涡破碎时机提前,当地后1/2弦长区域产生了比较明显的流动分离。     

月面远程运输飞行轨迹优化设计

针对月球表面不同区域之间的载人或载货运输问题,设计了一种基于上升-巡航-下降模式的燃料最省飞行轨迹。首先通过求解不同飞行时间的Lambert问题确定了最佳飞行时间,并获得了对应的双脉冲解,然后利用有限推力替代两次速度脉冲,建立了非线性规划问题,求解得到了有限推力燃料最省飞行轨迹。优化设计过程中主要研究了两个主要难点:bang-bang控制与飞行高度约束。这两个问题通过推力加速度与飞行时间的数值延拓得以解决,同时揭示了月面飞行的基本原理。最后给出了3种不同应用场景的仿真算例,仿真结果表明,当飞行时间为小时量级时,上升-巡航-下降飞行模式下的优化解即为燃料最优解,如果飞行距离较远,则还需要适当增加飞行时间从而满足飞行高度约束。     

Automatic differentiation based discrete adjoint method for aerodynamic design optimization on unstructured meshes

A systematic methodology for formulating, implementing, solving and verifying discrete adjoint of the compressible Reynolds-averaged Navier-Stokes (RANS) equations for aerodynamic design optimization on unstructured meshes is proposed. First, a general adjoint formulation is con-structed for the entire optimization problem, including parameterization, mesh deformation, flow solution and computation of the objective function, which is followed by detailed formulations of matrix-vector products arising in the adjoint model. According to this formulation, procedural components of implementing the required matrix-vector products are generated by means of auto-matic differentiation (AD) in a structured and modular manner. Furthermore, a duality-preserving iterative algorithm is employed to solve flow adjoint equations arising in the adjoint model, ensur-ing identical convergence rates for the tangent and the adjoint models. A three-step strategy is adopted to verify the adjoint computation. The proposed method has several remarkable features:the use of AD techniques avoids tedious and error-prone manual derivation and programming;duality is strictly preserved so that consistent and highly accurate discrete sensitivities can be obtained; and comparable efficiency to hand-coded implementation can be achieved. Upon the cur-rent discrete adjoint method, a gradient-based optimization framework has been developed and applied to a drag reduction problem.     

Development of a micro gas turbine combustor with T-type vaporizers

The study includes the experimental investigation of the evaporation performance of T-type vaporizer,mainly studied the relationship of the inlet air temperature and vaporizer wall temperature with the evaporation ratio.Then,it studied the LBO(lean blow out) and combustion efficiency of the micro aero-engine combustor with T-type vaporizer on the normal pressure test rig.The inlet air condition is environmental pressure and temperature.The gas analysis method is used to study the combustion efficiency,and the inlet air temperature is 300 K,400 K and 500 K.It could be concluded that the evaporation performance is improved with the increasing of the inlet air temperature and vaporizer wall temperature;the average LBO is 0.003;the combustion efficiency rises with the inlet air temperature,and it remain constant when the fuel/air ratio changed in the range from 0.008 to 0.02.The vaporization ratio is the key factor to determine the combustion performance.      

石英挠性加速度计阻尼参数闭环检测方法

石英挠性加速度计作为一种高精度惯性测量传感器,被广泛用于航天器姿态控制及惯性导航中。在石英挠性加速度计设计时,摆组件在腔体内的阻尼系数是一项重要的参数。与摆组件的转动惯量及挠性梁刚度等参数不同,阻尼系数与摆片的表面积、摆组件工作间隙、大气压强等多种因素相关。为了获取石英挠性加速度计正常工作状态下阻尼特性参数,研究了一种基于系统闭环频率响应的阻尼系数测量方法。利用水平振动台获取石英挠性加速度计幅频特性曲线,采用最小二乘参数拟合的方法对石英挠性加速度计阻尼特性参数进行辨识。利用辨识得到的阻尼系数进行仿真,并绘制幅频特性曲线与实际采样输出比对,验证了基于系统频率响应的闭环测量方法有效可行。     

机载机电系统可靠性的计算机辅助分析方法

 为了提高机载机电系统的可靠性,机载机电系统常采用余度系统,以达到故障容错,进而实现整个飞机系统的高可靠性和安全性。开发适应于余度间耦合、动态性能降级的ReliaApp可靠性分析评价软件平台,通过有效综合故障模式影响（FMEA）、故障树分析（FTA）和Markov状态转移链法,实现不同容错设计方案的选择、机电系统的可靠性定量评价并给出系统的薄弱环节,为系统的余度配置和改进设计提供软件设计与评估平台,以确保飞机系统的高可靠性和安全性。实例应用表明该软件平台是飞机机载机电系统可靠性设计与评价有效的计算机辅助工具。     

单通道DRFM的数字多普勒产生技术

根据脉冲多普勒雷达信号处理的相参性要求,提出以相位控制为基础的多普勒干扰信号产生方法.针对单通道采样结构的数字射频存储器,给出利用希尔伯特变换产生多普勒信号的数字算法.在Matlab中对多普勒干扰效果进行了仿真,对其FPGA实现方式进行了优化设计,结果表明了该算法的有效性和可实现性,最后对利用数字射频存储器实施多种多普勒干扰进行了研究.     

极限信号计算机试飞方法研究

介绍了极限信号计算机在试飞中遇到的问题及其解决办法,以最大允许M数为例,讲述了如何采用合理的技术手段来满足告警条件,以及告警精度的计算方法,重点介绍了最小二乘曲线拟合在本次试飞数据处理中的应用.