航天产品实施通用化、系列化、组合化有关问题的研究

阐述了在航天产品研制中全面实施“三化”是以最少人力、最低成本、最短研制周期满足最可靠产品的重要途径和手段,分析了目前航天产品实施“三化”存在的主要问题及原因,探讨了实施的基本思路,从意识形态、组织机构和政策倾斜等方面提出了加强“三化”工作的对策。     

液冷头盔致冷效能的医学研究

在45℃高温条件下,应用液冷头盔给10名被试者的头颈部致冷,散热效能较高,可带走安静时30.9％～48.3％的代谢产热。降低身体的热蓄积,减少出汗,减慢心率、直肠温度和皮肤温度的上升速率。对头颈部致冷可降低身体的热紧张度50％～70％,明显改善对温热的舒适感觉。同时表明,致冷液温、流量及液流走向,对致冷效能均有显著影响。为液冷头盔及致冷装置的设计,提供了医学实验依据。     

自硬树脂砂型的开裂原因及防止措施

简述了冷硬树脂砂型在某些情况下的产生开裂的原因及机理，讨论了几种解决的方法，有利于改进产品质量，减少双方的经济损失。     

航天器舷窗玻璃超高速撞击损伤与M/OD撞击风险评估

用北京卫星环境工程研究所的18mm口径二级轻气炮(TLGG)和20 J激光驱动微小飞片装置(LDFF-20)对用作航天器舷窗玻璃的熔融石英玻璃的超高速撞击损伤特性进行了实验研究和分析.其中,TLGG发射的球形铝弹丸直径分别为1 mm和3 mm,速度2～6.5 km/s;LDFF-20发射的圆柱形飞片厚度7 μm,直径1 mm,速度1～8.3 km/s.撞击结果为:对12 mm厚的熔融石英玻璃,直径为3mm的弹丸甚至在2.8 km/s的低速下就将其穿透,而直径为1 mm的弹丸在6.5km/s的高速下没有穿透,这说明弹丸直径对撞击损伤特性有很强的影响;LDFF-20发射的微小飞片的撞击仅在玻璃表面产生很浅的凹坑,没有裂纹产生,但微小飞片的累积撞击损伤明显地降低了玻璃的透光性.实验初步获得了侵彻深度PC、侵彻直径D1与弹丸撞击速度Vp、弹丸质量Mp之间的经验关系.依据实验结果和目前的微流星体/空间碎片(M/OD)环境工程模型,建议对于高度为400 km、轨道倾角42°、寿命为3年的典型航天器,其舷窗玻璃的临界安全(非穿透)厚度至少为12mm.     

一种新型空间微小碎片超高速碰撞试验地面模拟方法

文章简要叙述了空间微小碎片环境及其对航天器的影响,同时介绍了一种新型空间微小碎片超高速碰撞地面模拟方法——激光驱动飞片技术。     

不同氧化剂对丁羟(HTPB)推进剂老化性能影响的研究

本文研究了不同氧化剂对丁羟(HTPB)推进剂老化性能的影响.实验结果表明:随着推进剂老化时间的延长,最大拉伸强度增加,伸长率降低,邵氏硬度升高,失重百分数略有下降,而相对交联密度也上升.由此可以得出结论:热稳定的、产物氧化性弱的氧化剂,对于提高丁羟推进剂的老化性能是有益的.本文进一步用热重分析方法和红外光谱法对上述结果作了验证,并对丁羟推进剂的老化机理进行了初步探讨.     

Structure and kinetic properties of slow-mode shocks associated with magnetic reconnection in the near-Earth magnetotail

We study the structure and kinetic properties of slow-mode shocks near the plasma sheet boundary layer (PSBL) associated with magnetic reconnection by Cluster observation. The presence of slow-mode shocks is confirmed by traditional Rankine–Hugoniot (RH) analysis and Monte-Carlo shock fitting method. The Walén analysis, applied to the tailward flow associated with slow-mode shocks, also supports that plasma was accelerated across a Petschek-type slow-mode shock connected to the diffusion region. Back-streaming ions were observed on the shock layer, and cold ions were accelerated and heated by slow-mode shocks. In addition, whistler and electrostatic solitary waves were observed around the slow-mode shocks. These waves might be excited by the observed field-aligned electron beams near the shocks.     

J2级经纬仪竖盘指标自动补偿误差不确定度

介绍了按照ＪＪＧ４１４—９４《光学经纬仪》检定、校准Ｊ２级经纬仪竖盘指标自动补偿误差时，依据“’９３国际指南”要求，对其测量不确定度进行的分析、计算。     

Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

亚跨超CFD软件平台研制

亚跨ＣＦＤ软件平台研制的宗旨是综合国内外计算流体动力学的最新研究成果，用计算机软件技术的新发展，建立一个面向对象的计算流体动力学的研究开发环境，加快计算流体动力学最新成果向工程应用的转换速度。本文介绍初级版本的研究进展和研究成果，主要匝数值网格生成技术，流场解算器，面向对象的界面设计等三部分组成。