钛合金TC11深孔钻削刀片材料的选择

在研究了钛舍金材料切削性能的基础上，针对钛合金的特点，选用了五种国内常用的硬质舍金刀片材料，对钛合金进行深孔钻削刀具磨损试验。结果表明，确定了适合钻削钛合金TC11的硬质合金刀片材料。     

时效处理对Rene''220合金力学性能的影响

利用扫描电镜、拉伸试验机和蠕变实验机研究了不同时效制度下Rene’220合金室温及700℃的拉伸性能和700℃高温持久性能的变化规律。结果表明，随着一次和二次时效温度的升高，室温和高温强度呈下降趋势，而高温持久寿命随两次时效温度的变化均存在一个最大值，合金强度和持久性能最佳结合的时效制度为：830℃／4h／炉冷＋760℃／10h／空冷。     

先进战斗机控制分配方法研究综述

综述了先进战斗机控制分配方法的研究和应用状况。文中首先介绍了4种主要的控制分配方法———广义逆法、串接链法、直接分配法和数学规划法,给出各种方法在飞行控制系统分配应用中的限制,然后简单介绍控制分配方法在现实飞行控制系统中的应用情况,最后对控制分配中的几个关键问题进行了分析总结。     

叶轮机械三维粘性动静叶干涉的数值模拟

本文发展了 1套模拟叶轮机械三维粘性动静叶干涉的数值方法。在成熟的空间离散方法基础上 ,提出了 1种高效的双时间步隐式时间推进方法 ,并构造了一种保证守恒的动静叶交界面处的数值通量计算方法。本文对某三维亚音速涡轮的动静叶干涉进行了数值模拟 ,结果与实验符合较好。     

工程应用中的随机振动试验技术研究

阐述了机载电子设备随机振动试验的分类 ,并对宽带随机振动谱型的计算方法 ,振动推力及位移的指标进行了分析探讨。研究了试验的实用技术及控制方式的选择要点。最后给出了一个机载电子设备振动故障分析的例子。     

Ti2AlNb基合金的ISM熔炼研究

讨论了Ti2AlNb基合金的熔炼特点,概括介绍了真空水冷铜坩埚感应凝壳熔炼的设备结构原理和工艺技术,结合Ti2AlNb基合金的熔炼实践,研究了合金元素的加入形式、熔炼室真空度对合金铸锭的均匀性以及合金中Al挥发烧损的影响规律。结果表明:采用水冷铜坩埚真空感应凝壳熔炼Ti2AlNb基合金,合金铸锭成分均匀性很好,随着熔炼工艺的不同,Al挥发烧损在5％～10％（质量分数）之间。     

300M钢纯洁度磁粉检验磁痕现象的分析

采用交、直流磁粉检验并结合金相试验、电子探针试验及微量元素含量分析的方法，对３００Ｍ钢磁痕现象的本质进行了分析。结果表明，采用磁粉检验方法对航空优质钢进行纯洁度检验是可信的。     

Specification and Performance of Passive Sonar Spectral Estimators

The application of existing estimation theory to the problem of specification and performance of passive sonar spectral estimators is considered. The classification function is addressed, so that the signal is assumed to be present, and so that the energy arrival angle is known. The spatial filter considered is a line array of M equally spaced omnidirectional hydrophones. Signal and ambient noise are both zero-mean, wide-sense, stationary Gaussian random processes that differ in their spatial correlation across the face of the array. The signal is a plane wave that can be made totally spacially corrected between array elements by inserting delays between sensors to invert the signal propagation delay. The noise correlation is a function of frequency, bandwidth, element separation, and the relative time delay between sensors. Under these assumptions, the Cramer-Rao lower bound is derived for the class of unbiased estimates of signal power in a narrow frequency band at the hydrophone in the presence of correlated ambient noise of known power. The bound is examined numerically, resulting in a threshold phenomenon with M that constitutes a new design consideration. In addition, there is a striking insensitivity to realistic values of ambient noise correlation, and there are ranges in signal-to-noise ratio for which one gains more by increasing M than by increasing the bandwidth-time product. Specific processors, including a new unbiased estimator when noise power is unknown, are developed.     

Radar Performance with Multipath Using the Complex Angle

The complex angle (CA) method for resolving a low angle target from its multipath signal is evaluated in the presence of system noise. It is shown that standard deviation improvements of around 3-to-1 can be achieved at a 20-dB signal-to-noise power ratio relative to a normal monopulse system without the CA. It is also shown that the CA method is unbiased, giving bias improvements of as much as 100 times relative to normal monopulse. Evaluation of the assumptions in the technique shows very little sensitivity to knowledge of the reflecting surface's conductivity or dielectric constant. However, the method is somewhat sensitive to knowledge of surface roughness.     

固体火箭发动机寿命预估的一种考虑

利用弹性－粘弹性对应原理，分析长期贮存固体推进剂药柱由环境温度变化引起的热应力，计算药柱损伤，并对发动机寿命进行预估。理论分析和算法具有普遍性，可供工程设计参考。