Antideuterons as an indirect dark matter signature: Si(Li) detector development and a GAPS balloon mission

The General AntiParticle Spectrometer (GAPS) is a novel approach for indirect dark matter searches that exploits cosmic antideuterons. GAPS complements existing and planned direct dark matter searches as well as other indirect techniques, probing a different and unique region of parameter space in a variety of proposed dark matter models. The GAPS method involves capturing antiparticles into a target material with the subsequent formation of an excited exotic atom. The exotic atom decays with the emission of atomic X-rays and pions from the nuclear annihilation, which uniquely identifies the captured antiparticle. This technique has been verified through the accelerator testing at KEK in 2004 and 2005. The prototype flight is scheduled from Hokkaido, Japan in 2011, preparatory for a long duration balloon flight from the Antarctic in 2014.     

Simulation of the flow around a stationary circular cylinder taking into account laminar-turbulent transition

We consider a problem of a stationary incompressible viscous fluid flow around a flat circular cylinder. In the vicinity of the critical Reynolds number Re _cr a stepwise drop of the cylinder drag takes place, which is called the drag crisis.     

Impact of agents mixing velocity in diffusion flame on nitric oxide emission

The results of analyzing an impact of mixing velocity on the stoichiometric surface of a laminar diffusion methane-air flame on nitric oxides formation are presented. The conclusion about the nonlinear and steady decrease of nitric oxides emission at the increase of mixing velocity is made. The relationship is presented, showing that at the expense of non-equilibrium effects it is possible to provide a significant decrease of nitric oxides emission in diffusion combustion.     

Three-dimensional numerical studies of a jet airflow around the duct platforms of the turbine nozzle clusters

This paper presents the results of three-dimensional numerical studies of hydrodynamics and heat exchange on the models of flat plates in the jet airflow. These results are compared with the experimental data. A three-dimensional model for determining the thermal condition of the nozzle clusters in the conjugated formulation is proposed. Also presented are the data on optimization of the system used for the jet airflow around the duct platforms of the nozzle clusters.     

Local fracture of the burning solid propellant

The problem of fracture mechanics for the solid propellant deteriorated by a crack-shaped cavity, the surface of which burns is considered. It is assumed that the propellant reagents are uniformly distributed in the solid phase while the combustion products are gaseous. The sufficient condition for the “combustion -fracture” stability regime is obtained.     

Pareto-optimal solution of a two-objective problem in choosing conditions of monoimpeller milling

A problem of optimization of cutting parameters with respect to the criteria of maximum efficiency and maximum tool resistance is formulated. To solve the problem, a method is developed and applied for determining the Pareto-optimal values of machining conditions in milling the present-day GTE monoimpeller blade passages with a circular milling cutter.     

Gasodynamic characteristics of a combustion chamber in the integrated power plant with an asymmetric air intake

The results of experimental investigations of gasodynamic characteristics of a combustion chamber model in the integrated power plant (IPP) with an asymmetric air intake are presented. The influence of an angle of air supply into the chamber model on hydraulic losses and the flow structure is shown at different air flowrates, relative values of the minimal flow section area of the feeding air intake pipes, under changes of the flowrate of gas simulating gas generation products and geometric model parameters. A technique for measuring the concentration of carbon dioxide simulating IPP gas generation products in the combustion chamber air flow and the results of experimental investigations of a mixture formation process in the combustion chamber model are described.     

Response of the EIA ionosphere to the 7-8 May 2005 geomagnetic storm

In this paper, response of low latitude ionosphere to a moderate geomagnetic storm of 7–8 May 2005 (SSC: 1920 UT on 7 May with Sym-H minimum, ∼−112 nT around 1600 UT on 8 May) has been investigated using the GPS measurements from a near EIA crest region, Rajkot (Geog. 22.29°N, 70.74°E, Geomag.14°), India. We found a decrease in total electron content (TEC) in 12 h after the onset of the storm, an increase during and after 6 h of Sym-H deep minimum with a decrease below its usual-day level on the second day during the recovery phase of the storm. On 8 May, an increase of TEC is observed after sunset and during post-midnight hours (maximum up to 170%) with the formation of ionospheric plasma bubbles followed by a nearly simultaneous onset of scintillations at L-band frequencies following the time of rapid decrease in Sym-H index (−30 nT/h around 1300 UT).     

A mission template for exploration and damage mitigation of potential hazard of Near Earth Asteroids

The Apophis Exploratory and Mitigation Platform (AEMP) concept was developed as a prototype mission to explore and potentially deflect the Near Earth Asteroid (NEA) 99942 Apophis. Deflection of the asteroid from the potential 2036 impact will be achieved using a gravity tractor technique, while a permanent deflection, eliminating future threats, will be imparted using a novel albedo manipulation technique. This mission will serve as an archetypal template for future missions to small NEAs and could be adapted to mitigate the threat of collision with other potential Earth-crossing objects.     

The conundrum of software estimation models

There are many sophisticated models and methods for estimating the size, cost, and schedule of software projects. However, the ability to accurately estimate software cost, size, or schedule is still dubious. In general, the predictive accuracy of models for estimating software development cost and schedule has not been shown to be better than “within 25 percent of actual cost or schedule, about one half of the time”, especially for Department of Defense software efforts. The same is true for software size estimating models and methods, although there are some studies that have shown superior results. For software support (or maintenance) cost estimation, no model has been demonstrated to be accurate. This paper presents a summary of efforts performed to date which demonstrate the accuracy (or lack thereof) of software models. The results of several studies in the areas of software development cost and schedule estimation, size estimation, and support cost estimation are presented to show what these models can and cannot do. Some ideas for improvement are also presented, including the results of some studies which may lead to a resolution of the accuracy conundrum which currently exists