杨氏双缝干涉光程差近似计算的弱化条件分析

利用平面几何勾股定理,推导出杨氏双缝干涉实验光程差的准确表达式,对光程差表达式进行同解变换,反演了明纹中心坐标与光程差的函数关系,并对明纹中心坐标表达式进行了分析讨论,给出了数值解,得出了 5点结论。结论表明,杨氏双缝干涉实验光程差近似计算的条件可弱化为光程差远小于双缝间距,且利用经典近似方法计算明纹中心坐标在干涉级次较大时误差较大。     

基于拓扑优化和形状优化的桨叶结构设计

直升机旋翼桨叶剖面结构设计是研究旋翼动力学设计的基础。提出一种联合拓扑优化和形状优化的 两级优化设计方法,可用于桨叶剖面结构的设计。第一级优化以变密度法(SIMP)作为拓扑优化的材料插值方 法,以桨叶体积最小化为设计目标,约束桨叶节点位移和应力,建立桨叶的拓扑优化求解模型;第二级优化以重 构的桨叶模型为基础开展形状优化,降低局部应力集中以及找到合理的边界节点位置。对优化后的模型进行 有限元分析,结果表明:通过拓扑优化和形状优化的两级优化,能够得到满足强度和稳定性要求的结构布局,为 桨叶结构设计提供指导方案。     

一种平板螺旋式诱导轮的扬程计算法

目前平板螺旋式诱导轮的扬程计算法大都没有考虑诱导轮出口涡流区的影响,计算出的扬程和实际扬程有较大的偏差,涡流区的存在一方面会减小主流过流面积,使液流出口速度增大,损失增加,另一方面涡流运动自身也会消耗能量,使得诱导轮的扬程有所降低.以径向平衡理论为基础,考虑诱导轮出口涡流区的影响,提出一种扬程的修正计算法,用该方法对两种诱导轮进行了计算,计算结果和试验实测值比较接近,可以更准确的计算非空化工况下诱导轮的扬程.     

CONTROL OF TWO DIMENSIONAL JETS USING MINIATURE ZERO MASS FLUX JETS

Zero mass flux jets, synthesized by acoustic actuators, have been used for the purpose of jet mixing enhancement and jet vectoring. Zero mass flux jets composed of entirely entrained fluid allow momentum transfer into the embedding flow. In the present experiments, miniature-scale high aspect ratio actuator jets are placed along the long sides and near the exit plane of a primary two-dimensional jet. In different modes, the primary jet can be vectored either towards or away from the actuator jets and the jet mixing is enhanced. The disturbance of the excitation frequency is developed while the unstable frequency of the primary jet is completely suppressed.     

ATM局域网仿真技术

简要介绍了 Ａ Ｔ Ｍ 局域网仿真的主要原理，以 Ｉ Ｂ Ｍ ８２６０ Ａ Ｔ Ｍ 交换机为例，具体分析了 Ａ Ｔ Ｍ 局域网仿真的实现细节。     

三硝基间苯二酚中硫酸测定的研究

本文研究了硫酸钡在氨水溶液中与ＥＤＴＡ的反应条件，提出用ＥＤＴＡ滴定法测定三硝基间苯二酚中的硫酸。本法准确度较高，稳定性好，操作简单，与样品标准值对照，结果满意。     

Airborne adaptive MTI scheme with preventing the whitening of thetarget

A new airborne MTI scheme that applies to non-homogeneous clutter environment is presented. Results of simulation have proved that the scheme has a superior ground clutter suppression performance and can effectively prevent the whitening of a target     

Optimum parameter matching obtained by experiments for coring drilling into lunar simulant

This paper performs a series of ground experiments (on the Earth) to obtain optimum parameter matching for a future core drill on the Moon. Three common stages, I, II, III, are recognized with respect to the cut per revolution (CPR), which is defined as the ratio between the feeding speed and the rotating speed. The optimum matching between the feeding speed and the rotating speed for drills locates at the boundary position between Stage II and Stage III, where the coring rate saturates and the weight on the bit and the driving torque are still low. Further data analysis of the ground experiments reveals that the optimum matching signifies a proportional relation between the maximum conveying rate (MCR) by the groove of the auger and its rotating speed. The kinetic analysis in an ideal condition without gravity, the friction from the auger groove and the pressure at the bit confirm a similar proportion. The correlation between the proportions needs further study to determine whether the optimum matching obtained on the ground can be directly applied to future drills on the Moon.     

《计算机组成原理》课程教学改革初探

《计算机组成原理》课程作为计算机专业中的一门相当重要的专业基础课,在计算机专业课程体系中占有很重要的地位。本文通过对《计算机组成原理》课程实际教学中存在的问题的分析,在教学内容及方法,实践教学,教材选用等各个方面提出了一系列的解决方案和改革措施。     

System of simulation training for unmanned aircraft

For proficiently operating an unmanned aircraft, the aircrew must be thoroughly trained. However, using practical equipment to train the aircrew is work of high cost and risk. In this paper, a system of simulation training for unmanned aircraft is introduced. Its function and composition are explained in detail. In practice, the system not only decreases training cost and risk, but also strengthens training effectiveness and diversity