Multiposition alignment of strapdown inertial navigation system

The authors demonstrate that the stationary alignment of strapdown inertial navigation system (SDINS) can be improved by employing the multiposition/technique. Using an observability analysis, it is shown that an optimal two-position alignment not only satisfies complete observability conditions but also minimizes alignment errors. This is done by analytic rank testing of the stripped observability matrix and numerical calculation of the error covariance. It is also shown that an optimal three-position alignment accelerates the convergence of the alignment error compared with two-position alignment     

Optimum gain control for A/D conversion using digitized I/Q data inquadrature sampling

Calculation of optimum gain for minimum distortion due to A/D (analog-to-digital) conversion requires the estimation of the input signal strength. To use a common AGC (automatic gain control) for both the I/Q (in-phase and quadrature) signals, it is efficient to estimate the input signal strength using the quantized A/D output from both channels. Assuming a Gaussian input, the relationship between σ of the input of the A/D converter and E(|x|+|y|) and E(max(|x|,|y|)+1/2 min (|x|,|y|)) for t quantized I/Q output x and y is derived. Numerical results obtained using the derived expression and the statistical data obtained through simulation show excellent agreement. It is concluded that, because of its simplicity, the cubic equation obtained by fitting the numerical results should be useful     

Comments on `Tracking a maneuvering target using input estimation''

P.L. Boglar (see ibid., vol.AES-23, no.3, p.298-310, May 1987) developed a recursive formulation of the Chan, Hu, and Plant (CHP) algorithm, and the results of the simulation verified the performance improvements. The commenter claims that Bogler obtained an incorrect recursive formulation of input estimation because he incorrectly used the formulation of the Kalman filter. The commenter presents calculations that aim to demonstrate this claim     

Carrier Tracking by Smoothing Filter Improves Symbol SNR

The potential benefit of using a smoothing filter to estimate a carrier phase over use of phase-locked loops (PLL) is determined. Numerical results are presented for the performance of three possible configurations of an all-digital coherent demodulation receiver. These are residual carrier PLL, sideband-aided residual carrier PLL, and finally sideband aided with Kalman smoother. The average symbol SNR after losses due to carrier phase estimation is computed for different total power SNRs, symbol rates, and symbol SNRs. It is found that smoothing is most beneficial for low symbol SNRs and low symbol rates. Smoothing gains up to 0.7 dB over sideband-aided residual carrier PLL, and the combined benefit of smoothing and sideband aiding relative to residual carrier loop is often in excess of 1 dB.     

A Closely Regulated TWT Converter

The design concept for the traveling wave tube amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics were utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power traveling wave tube (TWT), and at the same time operate at an efficiency of better than 90 percent from a 30-volt source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data is presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered. The circuit provides better than 0.5 percent regulation against load change, input voltage change, and over-operating temperature range of from -20 to + 80°C, with output ripple voltage of less than 2 volts peak-to-peak on top of the 3600-Vdc output. The measured efficiency was typically 87 percent. and recommendations are included to improve this to in excess of 90 percent.     

On Optimal Control of Linear Systems in the Presence of Multiplicative Noise

This correspondence considers the problem of optimal regulator design for discrete time linear systems subjected to white state-dependent and control-dependent noise in addition to additive white noise in the input and the observations. A pseudo-deterministic problem is first defined in which multiplicative and additive input disturbances are present, but noise-free measurements of the complete state vector are available. This problem is solved via discrete dynamic programing. Next is formulated the problem in which the number of measurements is less than that of the state variables and the measurements are contaminated with state-dependent noise. The inseparability of control and estimation is brought into focus, and an "enforced separation" solution is obtained via heuristic reasoning in which the control gains are shown to be the same as those in the pseudo-deterministic problem. An optimal linear state estimator is given in order to implement the controller.     

X-ray emission from Be star/X-ray binaries

Observations of X-ray emission from Be star/X-ray binaries are reviewed. Some optical characteristics of these binaries are also presented. Theoretical aspects pertaining to the X-ray emissions are given.     

Nondestructive Characterization of RBSOA of High-Power Bipolar Transistors

Reverse-bias safe operating area (RBSOA) of high-power Darlington transistors is characterized using a 120 A/1000 V nondestructive reverse-bias second breakdown tester designed and fabricated at Virginia Polytechnic Institute and State University. Elaborate RBSOA characteristics are generated with different forward/reverse base drives and collector current levels. The effects of elevated case temperature and second-base drive on RBSOA of four-terminal Darlington devices are also discussed.