几何对称横向射流入射对尾喷流红外辐射特征抑制的数值研究

降低高温核心区长度是减小尾喷流红外辐射的有效途径。针对某轴对称收敛喷管,研究1种横向射流主动强化尾喷流掺混与红外抑制技术,采用横向射流技术强化外流与热喷流的掺混,通过数值模拟方法研究了2股横向射流喷射频率与流量变化对强化尾喷流掺混与红外抑制特性的影响规律。结果表明:在与横向射流流动方向垂直的探测面上尾喷流辐射强度衰降明显,探测角度为90°时红外辐射强度衰降可达48%。随着2股射流流量差的减小,强化掺混与红外抑制效果逐渐增强。     

惯性平台系统摇摆条件下的漂移处理方法

惯性平台在摇摆条件下,由于轴端摩擦力矩的存在,导致在摇摆运动时影 响平台稳定性,引起平台各轴附加常值漂移。介绍了两种惯性平台摇摆条件下的漂移处 理方法, 第一种方法利用平台轴端框架角传感器的输出数据, 首先使用离散傅里叶变 换得到数据频谱, 其次根据数据频谱设计数字滤波器, 对得到的数据进行滤波处理, 最后使用线性回归法对滤波后的数据进行拟合, 从而得到摇摆条件下平台摇摆漂移; 第二种方法使用加速度计的输出, 根据敏感的加速度可以得到敏感轴与重力加速度的 角度, 由此计算出摇摆过程的漂移速度。实验表明, 频谱分析法可以进行三个方向的 计算, 但台体轴结果的稳定性不好; 加速度输出拟合方法虽只可进行两个方向的计 算,但稳定性较好。     

基于声波传播时间估计的气流速度测量方法

 为实现对亚声速和超声速气流速度的统一测量,提出了一种基于声传感器的新型测量方法。首先,根据声波在亚声速和超声速气流中的传播特性,利用特定的测量装置建立了声波传播时间与气流速度之间的数学模型,从而将气流速度的测量问题转化为声波传播时间的测量问题。然后,在此基础上,利用计时法和最大似然估计(MLE)方法来估计声波传播时间;其中,计时法在实时性上优势明显,而MLE方法则在可靠性上优于前者。最后,分别从阵元位置扰动性、计时误差和克拉美-罗界(CRB)3个方面对所提算法的性能进行了分析与仿真验证。结果表明,该算法能够实现对亚声速和超声速气流速度的精确测量。     

UMR: A utility-maximizing routing algorithm for delay-sensitive service in LEO satellite networks

This paper develops a routing algorithm for delay-sensitive packet transmission in a low earth orbit multi-hop satellite network consists of micro-satellites. The micro-satellite low earth orbit(MS-LEO) network endures unstable link connection and frequent link congestion due to the uneven user distribution and the link capacity variations. The proposed routing algorithm,referred to as the utility maximizing routing(UMR) algorithm, improve the network utility of the MS-LEO network for carrying flows with strict end-to-end delay bound requirement. In UMR, first, a link state parameter is defined to capture the link reliability on continuing to keep the end-to-end delay into constraint; then, on the basis of this parameter, a routing metric is formulated and a routing scheme is designed for balancing the reliability in delay bound guarantee among paths and building a path maximizing the network utility expectation. While the UMR algorithm has many advantages, it may result in a higher blocking rate of new calls. This phenomenon is discussed and a weight factor is introduced into UMR to provide a flexible performance option for network operator. A set of simulations are conducted to verify the good performance of UMR, in terms of balancing the traffic distribution on inter-satellite links, reducing the flow interruption rate,and improving the network utility.     

A novel in-plane mode rotary ultrasonic motor

Ultrasonic motors have the merits of high ratio of torque to volume, high positioning precision, intrinsic holding torque, etc., compared to the conventional electromagnetic motors. There have been several potential applications for this type of motor in aerospace exploration, but bearings and bonding mechanism of the piezoelectric ring in the motors limit the performance of them in the space operation conditions. It is known that the Langevin type transducer has excel- lent energy efficiency and reliability. Hence using the Langevin type transducer in ultrasonic motors may improve the reliability of piezoelectric motors for space applications. In this study, a novel in-plane mode rotary ultrasonic motor is designed, fabricated, and characterized. The proposed motor operates in in-plane vibration mode which is excited by four Langevin-type bending vibra- tors separately placed around a ring-shaped stator. Two tapered rotors are assembled to the inner ring of the stator and clamped together by a screw nut. In order to make the motor more stable and convenient to fix, a thin cylindrical support is placed under the stator ring. Due to its no-bearing structure and Langevin transducer excitation, the prototype ultrasonic motor may operate well in aeronautic and astronautic environments.     

An integrated graphic–taxonomic–associative approach to analyze human factors in aviation accidents

Human factors are critical causes of modern aviation accidents. However, existing accident analysis methods encounter limitations in addressing aviation human factors, especially in complex accident scenarios. The existing graphic approaches are effective for describing accident mechanisms within various categories of human factors, but cannot simultaneously describe inadequate human–aircraft–environment interactions and organizational deficiencies effectively, and highly depend on analysts' skills and experiences. Moreover, the existing methods do not emphasize latent unsafe factors outside accidents. This paper focuses on the above three limitations and proposes an integrated graphic–taxonomic–associative approach. A new graphic model named accident tree(AcciTree), with a two-mode structure and a reaction-based concept, is developed for accident modeling and safety defense identification. The AcciTree model is then integrated with the well-established human factors analysis and classification system(HFACS) to enhance both reliability of the graphic part and logicality of the taxonomic part for improving completeness of analysis. An associative hazard analysis technique is further put forward to extend analysis to factors outside accidents, to form extended safety requirements for proactive accident prevention. Two crash examples, a research flight demonstrator by our team and an industrial unmanned aircraft, illustrate that the integrated approach is effective for identifying more unsafe factors and safety requirements.     

环境压力对双组分运动液滴蒸发特征影响的理论研究

为获得亚临界条件下,环境压力对双组分运动液滴蒸发特性的影响规律,基于多组分液滴蒸发模型,对癸烷—乙醇二元混合液滴在高温氮气环境下的运动蒸发过程开展模型研究。通过模型计算,获得了液滴内部浓度分布、温度分布和液滴速度随时间的变化;分析了在环境压力0.1MPa和2MPa下,不同浓度液滴温度、尺寸及表面乙醇浓度的变化特征。结果表明:双组分液滴运动蒸发过程中,内部存在显著浓度和温度梯度,传热扩散快于传质扩散。常压环境下,液滴温度经历瞬态加热和平衡蒸发两个阶段,而高压环境下,液滴温度逐渐升高至接近环境温度。双组分液滴蒸发过程中由于组分浓度随时间变化,其无量纲尺寸随时间变化明显偏离"d 2理论";环境压力越高,液滴运动的贯穿距离越短,蒸发速率越慢。乙醇浓度对液滴蒸发速率的影响有两方面:蒸发前期,乙醇浓度越高,液滴蒸发速率越快;而蒸发后期,乙醇浓度越高,液滴蒸发速率反而越慢。     

改进的Mori-Tanaka法在复合推进剂非线性界面脱粘中的应用

针对复合固体推进剂基体的大变形和界面的脱粘问题,对Mori-Tanaka法进行了改进.同时,为验证该方法的有效性,针对推进剂颗粒随机填充的特点,提出了一种含非线性界面脱粘的数值方法.最后以某推进剂配方为算例,对2种方法的计算结果进行了比较.结果表明,2种方法结果接近,从而验证了改进的Mori-Tanaka法的有效性,且...     

水平风洞模型自由飞试验技术研究现状及展望

介绍国外水平风洞模型自由飞试验技术研究现状,阐述水平风洞模型自由飞试验平台的组成、作用与意义,重点展望该试验技术的应用前景。对试验平台中动力相似模型设计加工技术、动力模拟技术、舵机运动控制技术、模型姿态实时精确测量技术、飞行控制系统设计与集成技术等关键技术问题进行分析,对发展该试验技术具有指导作用。完善水平风洞模型自由飞试验技术,把传统风洞试验拓展到流动-飞行-控制一体化试验,有利于全面研究和充分挖掘飞行器的气动性能与控制性能,对新一代飞机器的发展、新概念新技术的工程应用将起到重要的推动作用。     

采用移动粒子法对蒸发管结构优化

采用数值模拟方法研究在驻涡燃烧室试验中出现的部分燃油在外环冷却腔中燃烧的现象,分析导致过低的燃烧效率的原因,并通过优化设计对此现象加以解决.通过移动粒子半隐式方法的计算,结果基本还原了燃油回溅现象,查找出蒸发管结构设计中直段长度过短,并对蒸发管直段结构进行优化加长.在结构优化后的计算中,燃油回溅现象已经得到了很好的抑制,计算溅出的粒子由总数的50%降低至10%左右;试验结果得到的温升法燃烧效率也相应的由50%左右上升至80%～90%,从而验证了优化设计的正确性.