Radar network system to observe & analyze Tokyo Bay vessel traffic

A complete grasp of the actual vessel traffic flow by accurate observation is essential to carry out vessel traffic management, design of vessel traffic route, plan of port construction, etc. Up to now, the observation of vessel traffic has needed many efforts such as the use of a special ship or car equipped with radar observation systems and the observation staff preparation for a considerably long period. In order to perform accurate observation of vessel traffic without such efforts, the authors have developed a completely automated radar network system covering the main traffic route of Tokyo Bay. In August 2003, as the second remote radar station attaching AIS equipment was set at East Ogishima (the first was installed at the National Defense Academy in 2002), the observing range could be enlarged and cover most traffic routes in Tokyo Bay. These two radars can observe the vessel traffic in Tokyo Bay simultaneously so as to know the traffic flow accurately on the basis of analyzing the integrated radar data. In addition to the development of a radar network system, the software to analyze observed vessel traffic flow has been developed. This software has various functions such as tracking of ship's position, automatic determination of ship's size, animation of ship's movements, superposition of successive radar images, display of ship's tracks, calculation of ship's speed distribution, extraction of dangerous ship encounters using subjective judgment value and bumper model, etc. Some analyzed results on vessel traffic flow observed by the remote radars in January and September 2003 are shown in this paper.     

Hale引理证明的修正

本文指出了著名的Ｈａｌｅ引理证明中的不足之处，并给以完善。     

烟丝配料单片机控制系统

本文介绍了配料生产过程中单片机控制系统的硬件结构及软件流程。由于硬件和软件设计上都采用了模块化的结构，所以便于安装调试，整个系统可推广到诸如水泥、矿产、食品加工等生产中。     

Grasping Strategy in Space Robot Capturing Floating Target

When the space robot captures a floating target, contact impact occurs inevitably and frequently between the manipulator hand and the target, which seriously impacts the position and attitude of the robot and grasping security. “Dynamic grasping area” is introduced to describe the collision process of manipulator grasping target, and grasping area control equation is established. By analyzing the impact of grasping control parameters, base and target mass on the grasping process and combining the life experience, it is found that if the product of speed control parameter and dB adjustment parameter is close to but smaller than the minimum grasping speed, collision impact in the grasping process could be reduced greatly, and then an ideal grasping strategy is proposed. Simulation results indicate that during the same period, the strategy grasping is superior to the accelerating grasping, in that the amplitude of impact force is reduced to 20%, and the attitude control torque is reduced to 15%, and the impact on the robot is eliminated significantly. The results would have important academic value and engineering significance.     

线性调频半导体激光衍射光栅干涉仪

介绍一种以线性调频半导体激光为光源的衍射光栅干涉仪。激光与光栅上衍射的±１级衍射波会合，由于有光程差而发生光拍频，测量拍频信号的相位移则可测得光栅的位移。设计了一种克服激光波长漂移和空气折射率变化影响的对称差动光路，使这种方法达到实用化的程度，分辨力达到纳米级。此外，还介绍了应用于接触干涉仪的实验情况。     

铁基金刚石节块的热处理及其耐磨性能研究

首次提出了在烧结型金刚石工具的制造中引入热处理的新工艺，并系统地研究了淬火温度、淬火时间及回火温度等热处理工艺参数对热压烧结型铁基金刚石圆盘锯节块及其胎体材料机械性能的影响，同时对经热处理的铁基金刚石圆盘锯节块在石材旺苍红上进行磨损试验研究。试验结果表明，热压烧结型铁基金刚石圆盘锯节块胎体热处理的最佳工艺参数为：淬火温度为７６０～７９０℃、淬火时间为３．５ｍｉｎ、回火温度为２４５～３１５℃；经热处理后铁基金刚石圆盘锯胎体及节块的强度、硬度等机械性能有显著的提高，热处理也能明显改善铁基金刚石圆盘锯节块的耐磨性能。这说明将热处理工艺用于烧结型金刚石工具的制造中是切实可行的。     

Efficient implementation of Capon and APES for spectral estimation

Both the Capon and APES estimators can be shown to belong to the class of matched-filterbank spectral estimators and can be used to obtain complex spectral estimates that have more narrow spectral peaks and lower sidelobe levels than the fast Fourier transform (FFT) methods. It can also be shown that APES has better statistical performance than Capon. In this paper, we address the issue of how to efficiently implement Capon and APES for spectral estimation     

高强度钢Domex700MCD焊接性能研究

分析了Domex700MCD焊接性,并通过试验及数据分析表明,在焊接工艺中,采用混合气体保护焊、低合金结构钢焊丝ER69-3,通过控制焊接线能量,运用合理的焊接规范,可获得良好的焊缝机械性能。     

某锅炉钢结构角钢对扣箱型结构的焊接

某锅炉钢结构项目电梯井立柱采用了角钢对扣的箱型结构,此种箱形结构截面小,焊缝布置不对称,且焊缝长度较大,坡口切割变形、焊接变形难以控制,我们通过自制工装改进制作工艺解决了此类问题,满足该项目的验收要求。     

同伦法在现代飞机尾旋预测中的应用

在利用ＢＡＣＴＭ法对高性动性能飞机尾旋预测中，首先要求解平衡解，为此需要使用静态，强迫振荡天平气动模型和旋转天平气动模型，而在两气动模型转换过程中，常常遇到难找或不断得到平衡解的问题，针对这一问题，利用同伦法对气动模型进行处理，有效地了解决了该问题，同时，结合某战斗机进行了有关尾旋的计算和预测，结果表明，所提出的方法是可靠和切实可行的。