Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

Implementation of a novel matrix converter PMSM drive

This paper proposes a neural-network current-regulated switching strategy and an intelligent controller for a matrix converter permanent magnet synchronous motor (PMSM) drive system. By using this new switching strategy, the current harmonics of the system are effectively reduced. In addition, by using the intelligent controller, position control of the drive system can be achieved and an adjustable speed range from 1 r/min to 1500 r/min can be obtained. All the current-loop, speed-loop, and position-loop control algorithms are implemented by a 32-bit TMS320C40 digital signal processor. Several experimental results are shown to validate the theoretical analysis     

Power anomaly effects and costs in low-voltage mobile power systems

Electric power anomalies or disturbances can disrupt the normal operation of equipment, accelerate aging, or even cause outright failures thus resulting in increased costs of maintenance and reduced system reliability. Past research on the effects caused by power anomalies has been mostly focused on industrial, commercial, or residential systems, or on power distribution equipment. A literature survey reveals that there is no comprehensive review related to low-voltage (LV) power systems and utilization equipment applicable to military combat vehicles, such as aircraft and ships. This paper summarizes the results of a new literature survey that focused on the causes, effects, and mitigation methods for power anomalies typical of LV mobile power systems. Electric power anomaly cost data collected from the literature are also presented, from which the costs of anomalies to the national defense are estimated using some simple rationales.     

滑阀稳态液动力的计算和分析

以液氧/煤油补燃循环火箭发动机中流量调节器中滑阀为例,介绍了滑阀稳态液动力的一种计算方法,分析了不同结构参数下稳态液动力的变化规律,得出了滑阀的稳态液动力与滑阀位移、液流出口处的流道形状以及刃边厚度关系的一些初步结论。     

EUROCAT－X系统故障的诊断和分析

NESACC项目是我国空管史上规模最大的空管建设项目。该项目总投资近20亿人民币,分别在北京、上海、广州兴建三大区域管制中心,使用Thales公司研制的欧洲猫(EUROCAT-X)空管自动化系统,配备先进的自动化设备,使空管工作更为科学、直观、安全。EUROCAT-X系统自运行以来,运行情况基     

如何做好雷达管制下航空器的飞行动态监控

一、前言在雷达管制空域,只要管制员发出“radar contact”或“radaridentified”这样的指令,就担负起了对该航空器的一切动态过程的监控责任。如果对该机的飞行动态监控不到位,造成的一切不安全后果,雷达管制员都将难辞其咎。近来在全国范围内发生的几起不安全事件,多是由于管     

基于多相正交序列移位序列的CDMA通信系统

介绍多相正交序列的构造方法,对多相正交序列的自相关和互相关特性进行分析。提出采用多相正交序 列的移位序列作为扩频序列的通信方式,并给出接收端序列同步的实现方法。这种方式能解决低相数多相正交序列互 相关特性不理想,而高相数多相正交序列难以搜索的困难。     

加速器切线照相技术研究

根据工作实践研究了固体发动机切线照相无损检测中黑度分布、散射线防治、象质计使用、检测概率计算、脱粘临界值确定等技术问题.     

关于平面空穴流动的截断误差减小方法(英文)

提出了一种新的截断误差减小方法。该方法是利用在粗网格 ( 2 h)上估算截断误差进而减小在原始网格( h)上的误差的迭代过程 ,最终目的是利用粗网格得出更精确的结果以及发展一种新的粗网格直接数值模拟方法     

H-6部件与外挂天平的研制

介绍了H 6部件与外扌圭物测力试验的难点 :一是天平的设计载荷极不匹配 ,如机翼天平的滚转力矩是常规天平的 1 0多倍 ;二是模型尾部是船形尾段。采用常规的支撑方式 ,支杆强度太弱 ,试验不安全 ,同时也不利于多台天平的敷线 ,总体方案采用模型尾部与支杆合为一体的结构形式 ,既保证了试验安全又便于多台天平的敷线。天平设计首先保证试验安全 ,用双电桥提高天平的输出。试验结果表明 :总体试验方案正确 ,天平设计合理 ,支撑刚度好 ,测量精度高。