Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

Implementation of a novel matrix converter PMSM drive

This paper proposes a neural-network current-regulated switching strategy and an intelligent controller for a matrix converter permanent magnet synchronous motor (PMSM) drive system. By using this new switching strategy, the current harmonics of the system are effectively reduced. In addition, by using the intelligent controller, position control of the drive system can be achieved and an adjustable speed range from 1 r/min to 1500 r/min can be obtained. All the current-loop, speed-loop, and position-loop control algorithms are implemented by a 32-bit TMS320C40 digital signal processor. Several experimental results are shown to validate the theoretical analysis     

Power anomaly effects and costs in low-voltage mobile power systems

Electric power anomalies or disturbances can disrupt the normal operation of equipment, accelerate aging, or even cause outright failures thus resulting in increased costs of maintenance and reduced system reliability. Past research on the effects caused by power anomalies has been mostly focused on industrial, commercial, or residential systems, or on power distribution equipment. A literature survey reveals that there is no comprehensive review related to low-voltage (LV) power systems and utilization equipment applicable to military combat vehicles, such as aircraft and ships. This paper summarizes the results of a new literature survey that focused on the causes, effects, and mitigation methods for power anomalies typical of LV mobile power systems. Electric power anomaly cost data collected from the literature are also presented, from which the costs of anomalies to the national defense are estimated using some simple rationales.     

卫星交会的自主导航技术

论述卫星交会自主导航的飞行任务背景和概念 ,综述国内外学者正在进行探索研究的思路 ,以期引起国内学者的的注意、探讨和深入研究。     

卫星定位导航系统中各因素对D-R定位算法精度的影响

D- R定位算法在理论上可以用于定位。在实际工作中 ,用户的定位精度是进行定位时首先需要考虑的问题。文中主要讨论 D- R算法本身固有的定位误差。首先根据 D- R算法的定位公式推导出算法的精度误差因子。然后根据卫星定位导航系统的工作过程 ,确定了影响用户定位精度误差因子的因素并对这些因素对精度误差因子的影响进行了计算机仿真。仿真结果证明 D- R定位算法在一定条件下可以满足用户对定位精度的要求 ,用户精度误差因子可与现有的 GPS系统相当。     

EUROCAT－X系统故障的诊断和分析

NESACC项目是我国空管史上规模最大的空管建设项目。该项目总投资近20亿人民币,分别在北京、上海、广州兴建三大区域管制中心,使用Thales公司研制的欧洲猫(EUROCAT-X)空管自动化系统,配备先进的自动化设备,使空管工作更为科学、直观、安全。EUROCAT-X系统自运行以来,运行情况基     

如何做好雷达管制下航空器的飞行动态监控

一、前言在雷达管制空域,只要管制员发出“radar contact”或“radaridentified”这样的指令,就担负起了对该航空器的一切动态过程的监控责任。如果对该机的飞行动态监控不到位,造成的一切不安全后果,雷达管制员都将难辞其咎。近来在全国范围内发生的几起不安全事件,多是由于管     

加速器切线照相技术研究

根据工作实践研究了固体发动机切线照相无损检测中黑度分布、散射线防治、象质计使用、检测概率计算、脱粘临界值确定等技术问题.     

关于平面空穴流动的截断误差减小方法(英文)

提出了一种新的截断误差减小方法。该方法是利用在粗网格 ( 2 h)上估算截断误差进而减小在原始网格( h)上的误差的迭代过程 ,最终目的是利用粗网格得出更精确的结果以及发展一种新的粗网格直接数值模拟方法     

中山植物园植物定植图微机显示与管理系统

首先指出利用微机管理植物园取代落后的手工管理的意义。进而介绍了植物定植图微机显示与管理系统的具体实现途径，并描述了能将地图（含充色地图）、植物、宇符等录入。绘出，以及对植物进行检索显示等主要功能。