SCP－1型贴片机PLC程序的设计

介绍了在研制ＳＣＰ－１型贴片机过程中，采用可编程控制器（ＰＬＣ）对各外设进行控制的程序编制过程。着重分析了串行口通讯协议的设置，并以吸片过程为例，具体地说明了ＰＬＣ程序的编制方法。     

k-ε-g紊流燃烧模型数值研究

本文对k-ε-g紊流燃烧模型中模型系数C_R,C_(g1),C_(g2)的选定和计算浓度脉动均方值g的不同方法进行数值研究。计算结果表明模型系数值的选定直接与化学反应速率有关,而其中C_R影响最大。g的计算虽然可有不同方法,而其中微分方程求解最佳。并用实验数据来验证计算结果。     

Implementation of a three-phase high-power-factor rectifier with NPC topology

A three-phase four-wire power factor corrector based on neutral-point-clamped (NPC) topology is adopted to reduce the current harmonics and increase the input power factor. Using the NPC topology, the voltage stress of power switches can be reduced to the half of the dc-link voltage. With the dc-link voltage controller and the phase locked loop circuit, the balanced and sinusoidal line currents can be drawn from the ac supply system under the balance and unbalance mains voltages. The hysteresis current comparators are adopted in the current control loop to track the line current commands. Three voltage levels are generated on the ac terminal to the neutral point. Simulations and experiments are provided to verify the validity and the effectiveness of the proposed control scheme.     

三维模型中关键特性标注和提取的实现

关键特性作为"少数重要"的产品信息,是保证产品质量和顾客满意度的重要因素,其指定和标识需要与三维模型相结合才具有更直观的意义,同时也方便对其进行更有效的管理.本文给出了关键特性的定义和分类,提出了三维模型中关键特性的标注方法,通过对UG进行二次开发,实现了关键特性的属性添加和信息提取,并通过某型导弹弹头舱段壳体零件进行了验证.     

Digital Aircraft Sheet Metal Part Manufacturing System and Its Key Technology

The architecture of digital sheet metal manufacturing system is proposed based on the classification of sheet metal manufacturing information.The essence of digital manufacturing is the definition,management and transfer of information,and the key technologies are brought forward and described.It is pointed out that knowledge-based manufacturing elements design is necessary to make digital technology efficient.The management of all kinds of sheet metal manufacturing element information is to build single source of manufacturing data.Multi-state model-based digital transfer and coordination method is designed to provide a foundation for digital manufacturing of aircraft sheet metal part.The application of digital sheet metal manufacturing is exemplified with an aircraft sheet metal part.The application result is compared to that of the traditional analog transfer technology.It is shown that the developed technology can improve part quality,shorten manufacturing time and lower manufacturing cost.     

Implementation of a novel matrix converter PMSM drive

This paper proposes a neural-network current-regulated switching strategy and an intelligent controller for a matrix converter permanent magnet synchronous motor (PMSM) drive system. By using this new switching strategy, the current harmonics of the system are effectively reduced. In addition, by using the intelligent controller, position control of the drive system can be achieved and an adjustable speed range from 1 r/min to 1500 r/min can be obtained. All the current-loop, speed-loop, and position-loop control algorithms are implemented by a 32-bit TMS320C40 digital signal processor. Several experimental results are shown to validate the theoretical analysis     

Power anomaly effects and costs in low-voltage mobile power systems

Electric power anomalies or disturbances can disrupt the normal operation of equipment, accelerate aging, or even cause outright failures thus resulting in increased costs of maintenance and reduced system reliability. Past research on the effects caused by power anomalies has been mostly focused on industrial, commercial, or residential systems, or on power distribution equipment. A literature survey reveals that there is no comprehensive review related to low-voltage (LV) power systems and utilization equipment applicable to military combat vehicles, such as aircraft and ships. This paper summarizes the results of a new literature survey that focused on the causes, effects, and mitigation methods for power anomalies typical of LV mobile power systems. Electric power anomaly cost data collected from the literature are also presented, from which the costs of anomalies to the national defense are estimated using some simple rationales.     

EUROCAT－X系统故障的诊断和分析

NESACC项目是我国空管史上规模最大的空管建设项目。该项目总投资近20亿人民币,分别在北京、上海、广州兴建三大区域管制中心,使用Thales公司研制的欧洲猫(EUROCAT-X)空管自动化系统,配备先进的自动化设备,使空管工作更为科学、直观、安全。EUROCAT-X系统自运行以来,运行情况基     

如何做好雷达管制下航空器的飞行动态监控

一、前言在雷达管制空域,只要管制员发出“radar contact”或“radaridentified”这样的指令,就担负起了对该航空器的一切动态过程的监控责任。如果对该机的飞行动态监控不到位,造成的一切不安全后果,雷达管制员都将难辞其咎。近来在全国范围内发生的几起不安全事件,多是由于管     

加速器切线照相技术研究

根据工作实践研究了固体发动机切线照相无损检测中黑度分布、散射线防治、象质计使用、检测概率计算、脱粘临界值确定等技术问题.