The role of AVDR in linear cascade testing

Linear cascade testing plays an important role in the research and development of turbomachinery and is widely used over the world.The ideal cascade model of a turbomachinery blade row is two-dimensional.In actual linear cascade testing, the flow through the test section converges due to the development of the boundary layer and secondary flow along the sidewall surfaces of the test section.Axial velocity density ratio(AVDR) is adopted to account for the deviation of the tested cascade flow from the ideal 2D model.Among numerous published cascade works, the influence of AVDR on cascade performance is seen to be complicated with many affecting factors, such as those related to cascade/blade geometry and flow conditions.Also, controlling AVDR is limited by the facility capability.Furthermore, real blade-to-blade flow in turbomachines is usually associated with AVDR greater than unity due to limited span of blades between the hub and shroud such that cascade testing without reducing AVDR could be favored sometimes.All these facets add complexity and diversification to the matter.The current paper reviews previous studies and results on AVDR.Consolidated understanding on the role of AVDR and recommendations on how to deal with it in linear cascade testing are provided.      

弹性支撑条件下裂纹齿轮体有限元模拟与仿真

将齿轮与轴的装配支撑关系考虑为弹性支撑, 采用有限元数值分析ANSYS软件对故障齿轮的动力特性进行了模拟.研究了裂纹故障发生后齿轮动力特性的变化, 分析了不同大小和不同类型的故障对齿轮体动力特性的影响.结果表明:裂纹的大小和位置对动力特性都有影响, 但裂纹发生位置的影响要大于裂纹大小的影响, 即处于齿轮结构体中部的缺陷要比处于外边缘的缺陷对动力特性影响大.另外, 探讨了仿真时设置弹性支撑边界条件的方法, 并通过与固定支撑和自由支撑边界条件的比较, 给出了弹性支撑条件下分析结果的真实性和有效性, 为齿轮故障发生机理和诊断的研究提供了一种方法.      

某风扇/增压级非设计点性能计算及进气畸变影响分析

在原流线曲率法程序的基础上, 增加了适用于高速风扇/压气机的双激波损失模型.真实地反映了高速风扇/压气机的实际工作状况, 提高了预测高速风扇/压气机非设计点性能的准确性, 完善了分析进气畸变对风扇/压气机性能及稳定性影响的准三维计算模型.针对一台外涵转子叶尖马赫数大于1.4的大涵道比风扇/增压级, 计算分析了其非设计点性能以及进气畸变的影响.计算结果与试验结果吻合较好, 精度可靠, 可应用于工程实际.      

变截面U形通道内肋高对换热特性影响的实验

采用实验方法研究了在定常状态下, 肋的高度对横肋变截面U形通道内的换热特性的影响。通道内肋间距为15 mm, 肋的宽度均为2 mm, 肋的高度分别为1, 1.5, 2 mm和2.5 mm。雷诺数在12 000到56 000之间变化, 采用单元分析法, 以相同形状的无肋通道作为基准, 研究了肋的高度对肋间距为15 mm通道的换热效果及阻力影响, 得到了包括几何参数在内的经验关联式。结果表明, 有肋的通道换热都得到了增强;肋高度的变化对变截面蛇形通道换热的影响不是单调的, 而是呈多峰分布;肋的高度对阻力系数的影响却是随着肋高的增大而增大的。      

基于LMI活塞式发动机恒转速H∞动态输出反馈控制

汽油发动机具有非线性、时变时滞等特点, 传统PID控制方法很难保证发动机整个工作范围内恒转速控制的稳定性及性能要求.采用基于LMI(linear matrix inequality)的输出反馈H∞控制算法, 来实现活塞式汽油发动机的恒转速控制, 使其在负载扰动、工况变化和可变时间延迟的情况下都能保持期望的参考转速.离线仿真结果表明, 所设计的控制器满足小型无人直升机对发动机控制的抗干扰性、跟踪性要求, 并具有一定鲁棒性.      

发动机零部件稳态应力计算的状态函数法

借鉴发动机气动参数相似准则的基本思想, 提出了根据典型工作点的应力结果直接推算出其它状态点的状态函数法.利用该方法可以快速计算发动机任意状态点的稳态应力、位移、温度, 可以便捷地为构件寿命预估提供应力谱, 使发动机零部件寿命计算过程大大简化.该方法在发动机零部件寿命预估和管理等方面有较高的实用价值.      

翼身融合运输机分布式电推进系统设计及油耗评估

针对翼身融合运输机开展了分布式电推进系统的总体设计与油耗评估。通过数值计算完成了70t载质量翼身融合飞机的气动设计与优化。在巡航马赫数为0.80和10km高度的设计点,最大升阻比达到了24。通过求解积分边界层方程组,完成了电推进系统的总体设计。电推进系统包含10个推进风扇,风扇直径为1.45m,压比为1.35,巡航功率为2.94MW。建立了考虑燃烧过程的发动机一维性能模型,对发动机油耗进行了评估,获得了不同发动机循环参数下燃油消耗。建模结果表明,基于翼身融合布局和分布式电推进技术,可使运输机的油耗较C-17节省近50%。      

反推装置对翼身融合分布式推进系统气动性能影响数值模拟

为了研究新型反推装置对翼身融合分布式推进系统气动性能的影响,将机身简化为二维模型,利用数值模拟的手段来研究攻角、反推开度,以及风扇打开或关闭对飞行参数的影响,为翼身融合分布式推进系统的反推装置设计提供初步的意见和建议。结果显示:反推闭合和风扇打开之后该机型的升力系数和俯仰力矩系数都会有较大增加;随着反推开度的增加,升力系数和俯仰力矩系数也随之增加;来流攻角对翼身融合分布式推进系统的气动性能也有较大影响。      

感性耦合夹层等离子体隐身天线罩电磁散射分析

设计了一种石英夹层感性耦合等离子体（ICP）隐身天线罩模型,采用有限元与Z变换时域有限差分（ZT-FDTD）联合仿真的方法,建立了ICP放电的流体模型,得到不同气压及功率下与电磁散射相关的电子密度空间分布,在此基础上建立Z变换时域有限差分法模型,对石英夹层等离子体隐身天线罩的宽频段后向散射进行计算,同时利用微波干涉法及XFDTD软件对算法及程序进行验证。结果表明：感性耦合等离子体可产生较高密度等离子体,能有效实现雷达散射截面（RCS）的减缩,在气压为2 Pa时,碰撞衰减较弱,等离子体密度分布较均匀,衰减带宽集中在等离子体振荡频率附近,功率增加会使衰减峰值向高频方向移动,气压为20 Pa时,碰撞衰减增强,且等离子体密度分布有较大梯度,衰减带宽有效增加,同时RCS曲线的波动特性加强。     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.