Vibrations of a shell with the discretely attached dynamic subsystem

A problem on low vibrations of a thin spherical shell is considered. A solid of finite dimensions is discretely attached to the shell by means of an elastic rod system. The calculation examples are presented.     

Influence of climatic operational conditions of a helicopter on physico-mechanical properties of composite materials

The results of numerical and experimental study of physico-mechanical properties of composite materials are proposed and variations in rigidity characteristics of the hub working part of the hingeless type within the entire range of helicopter operational temperatures are evaluated.     

The RadioAstron project: Measurements and analysis of basic parameters of space telescope in flight in 2011–2013

The results of a large number of the antenna radiometric measurements at bands of 92, 18, 6.2, 1.35, and 1.7-1.2 cm are presented by the data of the standard telemetry system of the Spektr-R spacecraft. Both special sessions of calibration object observations in the mode of a single space radio telescope (SRT) operation and numerous observations of researched sources in the mode of the ground-space interferometer were used. The obtained results agree with the first results of Kardashev et al. (2013), i.e., within 10–15% at bands of 92, 18, and 6.2 cm and 20–25% at the band of 1.35 cm. In the main, the measurements for the eight subbands at wavelengths of 1.7-1.2 cm indicate a monotonic increase in the spectral system equivalent flux density (SEFD) of noise radiation with a frequency consistent with the calculated estimates for the discussed model. The sensitivity of the ground-space interferometer for the five subbands at wavelengths from 1.35 to 1.7 cm can be higher by a factor of 1.5, and for the three subbands from 1.35 to 1.2 cm lower by a factor of 1.5 than at the band of 1.35 cm. The SRT contribution to the interferometer sensitivity proportional to the square root of SEFD is close to the design one at the bands of 92 and 18 cm and decreases the design sensitivity approximately by a factor of 1.5 and 2 at the bands of 6.2 and 1.35 cm, respectively. These differences of implemented values from the design ones were not significantly affected the scientific program implementation.     

A method of airfoil shape completing

An iteration method for airfoil shape completing using the pressure coefficient distribution specified on its sought part is proposed. The incompressible flow viscosity is taken into account by the boundary layer model, the iteration process is constructed with the use of G.Yu. Stepanov’s idea. The solution algorithm is compiled and a set of numerical calculations is carried out. It is shown that the method proposed offers advantages over the well-known numerical-analytical scheme of solving mixed inverse boundary-value problems of aerohydrodynamics in the case of viscous incompressible fluid.     

Empirical modeling of the total electron content in the ionosphere

A method of modeling the total electron content (TEC) based on the semi-empirical ionospheric model developed in Irkutsk State University is suggested. Comparison with the Klobuchar model has shown that the proposed method provides a more accurate presentation of TEC. A conclusion is drawn that the use of this method for compensation of the ionospheric error in single-frequency navigation receivers would lead to a substantial increase in the accuracy of their positioning.     

基于Kriging模型插值的孔位修正策略

飞机装配时的孔位精度直接影响其最终装配质量，而待制孔零件易发生变形和整体偏移，因此一般通过基准孔信息对待制孔位进行补偿。提出一种基于Kriging插值的孔位修正方法，通过基准孔建立孔位理论坐标与实际偏差值的Kriging模型，进而预测待制孔的孔位偏差，并给出每个位置的预测标准误差，以指导基准孔的增添和布置。最后通过有限元和数值实验分别验证了零件在极限变形和整体平移旋转情况下该方法的有效性，实现了孔位估计误差小于0.3 mm。     

On the arc length of observations of a small solar system body sufficient to classify it as hazardous

This paper analyzes the accuracy of orbit determination calculated by observations of short arcs. In this case, we imposed the condition that the arc length and/or the distribution of arc observations should provide a confident classification of the orbit of a small celestial body allowing one to distinguish a potentially hazardous body, also including a threat of collision.     

The mass loss of spacecraft polyimide films under the action of atomic oxygen and vacuum ultraviolet radiation

The threshold values of the annual fluence of atomic oxygen (F _AO ≈ 10²⁰ cm^?2), as well as the ratios of the energy-flux density of vacuum ultraviolet radiation of the solar spectrum to the flux density of atomic oxygen (Φ _ν /Φ _AO ≈ 8 × 10^?15 mJ) were determined, which are characterized the influence of the synergistic effect on the mass loss of Kapton-H, PM-A, and PM-1E polyimide films, which are spacecraft materials.     

A Lunar Laser Ranging Retroreflector Array for the 21st Century

Over the past 40 years, the Lunar Laser Ranging Program (LLRP) to the Apollo Cube Corner (CCR) Retroreflector Arrays (ALLRRA) [1] has supplied almost all of the significant tests of General Relativity. The LLRP has evaluated the PPN parameters, addressed the possible changes in the gravitational constant and the properties of the self-energy of the gravitational field. In addition, the LLRP has provided significant information on the composition and origin of the moon. This is the only Apollo experiment that is still in operation. Initially the ALLRRAs contributed a negligible fraction of the ranging error budget. Over the decades, the ranging capabilities of the ground stations have improved by more than two orders of magnitude. Now, because of the lunar librations, the existing Apollo retroreflector arrays contribute a significant fraction of the limiting errors in the range measurements.The University of Maryland, as the Principal Investigator for the original Apollo arrays, is now proposing a new approach to the Lunar Laser Array technology [2]. The investigation of this new technology, with Professor Currie as Principal Investigator, is currently being supported by two NASA programs and by the INFN-LNF in Frascati, Italy. Thus after the proposed installation during the next lunar landing, the new arrays will support ranging observations that are a factor 100 more accurate than the current ALLRRAs.The new fundamental cosmological physics and the lunar physics [3] that this new Lunar Laser Ranging Retroreflector Array for the 21st Century (LLRRA-21) can provide will be described. In the design of the new array, there are three major challenges: (1) validate the ability to fabricate a CCR of the required specifications, which is significantly beyond the properties of current CCRs, (2) address the thermal and optical effects of the absorption of solar radiation within the CCR, reduce the transfer of heat from the CCR housing and (3) validate an accurate emplacement technique to install the CCR package on the lunar surface. The latter requires a long-term stable relation between the optical center of the array and the deep regolith, that is, below the thermally driven expansion and contraction of the regolith during the lunar day/night cycle.     

Analysis of shells of revolution under axisymmetrical loading using the quadrature method

To complete study [1], the procedure of applying the numerical quadrature method to analyzing the shells of revolution under axisymmetrical loading is presented.