空气中微细电火花沉积铜合金工艺方法

提出了一种在空气中将工具电极丝黄铜材料沉积到工件上的新工艺方法。实现该方法的基本条件为:(1)工具电极接脉冲电源正极;(2)在空气中放电;(3)窄脉宽配合宽脉间。通过大量实验对微细电火花沉积加工的工艺规律进行了系统深入的研究,得出各主要工艺参数对沉积工艺效果的影响规律。最终以黄铜电极丝为工具电极,在高速钢工件表面上沉积出直径为0.19 mm、高度为7.35 mm的微小圆柱体。利用SEM、能谱分析和X射线衍射及显微硬度测试等方法对沉积物进行分析,得出该沉积物的组织结构、化学成分和硬度等方面的基本性质,为进一步研究三维沉积加工奠定了基础。     

钢筋砼条基及独立柱基有效高度的实用计算公式

为了便于广大工程实践人员对基础有效高度的确定，根据规范GB50010－2002及GB50007－2002推导求解出基础有效高度的实用计算公式及计算表格。     

SINS／GPS组合系统的蒙特卡洛仿真

以考虑位置误差相关项的伪距率观测模型，对遥感中使用的SINS/GPS为距、伪距率组合系统进行了蒙特卡洛仿真。结果表明，组合系统的长期位置精度能达到5m以内；GPS数据更新率低于SINS，在GPS测量时间间隔内，组合系统的性能仅由SINS决定，虽然SINS的误差随时间积累，但在GPS测量时间间隔为秒数量级的情况下，即使采用中等精度的惯性的误差随时间积累，但在GPS测量时间间隔为秒数量级的情况下，即使采用中等精度的惯性仪表，其相对位置精度可达到厘米级（这里相对位置精度指组合系统在GPS测量时间间隔内位置误差的变化范围）。     

相位法曲面三维可测梯度极限的研究

简述了相位法曲面三维全场无接触检测的基本原理，研究了被测曲面的梯度变化对频谱分析和滤波处理的影响，推导出相位法曲面可测梯度极限的理论公式，并通过锥面测量验证了这一公式的正确性。     

危害性分析中的模糊数学方法

利用模糊集合理论对影响故障模式危害性的各因素进行了模糊化处理，建立了故障模式危害性评定的模糊评判模型，并阐述了模糊评判方法的基本步骤。     

支持MEMS的CAD/CAE系统结构研究

CAD/CAE技术在MEMS(Micro Electro Mechanical Systems)研究过程中具有非常重要的作用.本文首先介绍了用于MEMS的CAD/CAE技术特点,然后研究了MEMS CAD/CAE系统结构,给出了软件支持工具结构框图,指明了解决其中关键技术的途径.CAD/CAE技术的应用,将提高微型机电系统的设计质量,缩短研制周期,使之及早走向工业化.     

飞机V型外倾双垂尾载荷校准技术

根据垂尾载荷校准及建模需求,对飞机V型外倾双垂尾结构受载情况进行了分析和简化,确定了校准试验载荷,研制了垂尾载荷校准试验专用龙门梁架。采用液压协调加载技术,完成了外倾双垂尾载荷校准试验,建立了满足测载要求的载荷模型。此种方法充分利用了左右垂尾外倾、双垂尾之间空间较大的特点,对左右垂尾对称施加向外的单点、多点载荷,加载载荷侧向分量左右自平衡,垂向分量依靠飞机自身重量即可平衡,飞机不需要复杂的固定与约束。试验中采用先搭建龙门框架,再停放飞机的方法,降低了试验风险、加快了试验进度,取得了良好的试验结果,对其他此类结构的载荷校准具有一定的借鉴作用。     

Adaptive suppression of passive intermodulation in digital satellite transceivers

For the performance issues of satellite transceivers suffering passive intermodulation interference,a novel and effective digital suppression algorithm is presented in this paper.In con trast to analog approaches,digital passive intermodulation (PIM) suppression approaches can be easily reconfigured and therefore are highly attractive for future satellite communication systems.A simplified model of nonlinear distortion from passive microwave devices is established in consid eration of the memory effect.The multiple high-order PIM products falling into the receiving band can be described as a bilinear predictor function.A suppression algorithm based on a bilinear poly nomial decorrelated adaptive filter is proposed for baseband digital signal processing.In consideration of the time-varying characteristics of passive intermodulation,this algorithm can achieve the rapidness of online interference estimation and low complexity with less consumption of resources.Numerical simulation results show that the algorithm can effectively compensate the passive intermodulation interference,and achieve a high signal-to-interference ratio gain.     

Air route network optimization in fragmented airspace based on cellular automata

Air route network optimization,one of the essential parts of the airspace planning,is an effective way to optimize airspace resources,increase airspace capacity,and alleviate air traffic con gestion.However,little has been done on the optimization of air route network in the fragmented airspace caused by prohibited,restricted,and dangerous areas (PRDs).In this paper,an air route network optimization model is developed with the total operational cost as the objective function while airspace restriction,air route network capacity,and non-straight-line factors (NSLF) are taken as major constraints.A square grid cellular space,Moore neighbors,a fixed boundary,together with a set of rules for solving the route network optimization model are designed based on cellular automata.The empirical traffic of airports with the largest traffic volume in each of the 9 flight information regions in mainland China is collected as the origin-destination (OD) air port pair demands.Based on traffic patterns,the model generates 35 air routes which successfully avoids 144 PRDs.Compared with the current air route network structure,the number of nodes decreases by 41.67％,while the total length of flight segments and air routes drop by 32.03％ and 5.82％ respectively.The NSLF decreases by 5.82％ with changes in the total length of the air route network.More importantly,the total operational cost of the whole network decreases by 6.22％.The computational results show the potential benefits of the model and the advantage of the algorithm.Optimization of air route network can significantly reduce operational cost while ensuring operation safety.     

硅半球深腔结构无损检测技术

半球深腔的加工质量是决定硅基MEMS半球陀螺精度的关键因素之一，及时检测半球深腔的形貌参数并将其反馈至加工过程，是确保高性能MEMS半球陀螺研制成功的重要措施。由于硅半球深腔的深度较大，台阶仪和光学显微成像系统无法对半球深腔的形貌特征进行有效测量。因此,需要将硅深腔结构剖开后采用扫描电镜(SEM)进行检测。这种检测方式时间周期长，且属于破坏性的样本检测，效率和测试精度都较低。提出以硅半球深腔为模具，利用PDMS铸模将硅半球深腔的结构尺寸和表面形貌转移到PDMS凸起的半球模型上，通过检测PDMS半球模型的尺寸结构和表面形貌，即可反推出硅半球深腔的尺寸特征。经实验验证，脱模后的PDMS模型可以准确地反映出半球深腔的尺寸信息，测量结果的不确定度小于5‰，有效解决了硅半球深腔无损检测的难题。