在实时嵌入式环境下利用电子盘实现大容量数据记录的软件设计研究

嵌入式环境和实时操作系统目前广泛应用于航空领域。本文在介绍嵌入式系统的基础上,重点对实时多任务环境下大容量数据记录的实现方式进行了研究和利用,最后展望了电子盘实时多任务系统中记录大容量数据的前景。     

An Improved Nonlinear Dynamic Inversion Method for Altitude and Attitude Control of Nano Quad-Rotors under Persistent Uncertainties

Nonlinear dynamic inversion(NDI)has been applied to the control law design of quad-rotors mainly thanks to its good robustness and simplicity of parameter tuning.However,the weakness of relying on accurate model greatly restrains its application on quad-rotors,especially nano quad-rotors(NQRs).NQRs are easy to be influenced by uncertainties such as model uncertainties(mainly from complicated aerodynamic interferences,strong coupling in roll-pitch-yaw channels and inaccurate aerodynamic prediction of rotors)and external uncertainties(mainly from winds or gusts),particularly persistent ones.Therefore,developing accurate model for altitude and attitude control of NQRs is difficult.To solve this problem,in this paper,an improved nonlinear dynamic inversion(INDI)method is developed,which can reject the above-mentioned uncertainties by estimating them and then counteracting in real time using linear extended state observer(LESO).Comparison with the traditional NDI(TNDI)method was carried out numerically,and the results show that,in coping with persistent uncertainties,the INDI-based method presents significant superiority.     

阵风载荷减缓系统故障分析

阵风引起的额外载荷会引起飞机结构疲劳,降低结构使用寿命。采用非定常气动力有理函数拟合方法建立时域状态空间下的动力学系统,设计了阵风载荷减缓系统。研究了阵风载荷减缓系统3种典型故障模式(副翼偏转饱和、舵机卡死、副翼偏转延时)的力学建模方法,并对机翼在阵风减缓系统故障模式下的阵风响应进行分析。仿真结果表明,3种故障模式均不利于阵风载荷减缓系统对阵风载荷的减缓,对于一些特定情况,故障模式下的阵风载荷减缓系统不仅不能减缓阵风载荷,还会带来由副翼偏转不当引起的额外负载。     

采用霍尔传感器的旋翼频率采集设计

为达到对旋翼飞机的控制,需要对旋翼转速进行采集.霍尔转速传感器以其高可靠性等优点常被用来测量转速.介绍了一种使用霍尔传感器进行旋翼转速采集系统,包括硬件构架,逻辑采集单元和软件设计,并给出了优化策略;通过试验数据分析,采集精度达到了预期.     

供热系统集约化运行的能耗监测及节能调节问题探讨

对我校供热系统的现状进行了分析；指出了锅炉热效率及能耗监控方面的不足，并针对锅炉热效率提高和二次网循环泵变频调节进行了节能分析计算；同时根据我校实际情况对循环泵设备配置及控制进行了分析，提出了要加强技术指标量化考核和能耗监测，提高效率、节能降耗，实现供热系统的科学化、集约化运行。     

ENERGY-SAVING MATCHING STRATEGY AND EXPERIMENTAL STUDY OF PUMPING SYSTEM FOR TRUCK-MOUNTED CONCRETE PUMP

Aiming at the high fuel consumption and use-cost of truck-mounted concrete pump , an energy-saving matching strategy of pumping system is presented and the experimental study is conducted.Since pumping system occupies most resources of engine , the matching strategy between engine and main pump is analyzed to meet the load demand and reduce the engine rational speed drop.The testing method is established to measure the fuel consumption of engine under various working conditions , and the experimental data are analyzed to find the law of the fuel consumption of engine.The system performance can be improved by adjusting the system input value.Finally , the energy-saving matching strategy is established to reduce the fuel consumption of truck for unit workload , which provides a new approach for the energy-saving of truck-mounted concrete pump.     

导风轮叶片偏置对高压比串列离心压气机性能的影响

为提升高压比串列离心压气机的性能,借鉴常规一体化离心叶轮中偏置分流叶片的方法,针对某高压比串列离心压气机,应用数值仿真手段分析了串列叶轮中导风轮叶片周向偏置对压气机流场和性能的影响。通过对不同导风轮叶片偏置方案下压气机流场的分析,建立了压气机流动损失与偏置参数的关联性。研究表明:采用较大的偏置参数γ可降低导风轮叶片1前缘的激波强度,改善激波作用导致的泄漏涡破碎和流动分离,但过大或过小的γ方案中导风轮叶顶会出现二次泄漏致使低能流体的掺混损失增加;γ=65%方案压气机综合性能最佳,其压比和效率较γ=50%分别提高了1.5%和1.4%;对于串列离心压气机导风轮叶片周向位置的优化,在避免导风轮叶顶形成较强二次泄漏的前提下,应考虑采用较大的偏置参数γ,同时应防止诱导轮尾迹流体参与导风轮的叶顶泄漏。     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。