Multiposition alignment of strapdown inertial navigation system

The authors demonstrate that the stationary alignment of strapdown inertial navigation system (SDINS) can be improved by employing the multiposition/technique. Using an observability analysis, it is shown that an optimal two-position alignment not only satisfies complete observability conditions but also minimizes alignment errors. This is done by analytic rank testing of the stripped observability matrix and numerical calculation of the error covariance. It is also shown that an optimal three-position alignment accelerates the convergence of the alignment error compared with two-position alignment     

Carrier Tracking by Smoothing Filter Improves Symbol SNR

The potential benefit of using a smoothing filter to estimate a carrier phase over use of phase-locked loops (PLL) is determined. Numerical results are presented for the performance of three possible configurations of an all-digital coherent demodulation receiver. These are residual carrier PLL, sideband-aided residual carrier PLL, and finally sideband aided with Kalman smoother. The average symbol SNR after losses due to carrier phase estimation is computed for different total power SNRs, symbol rates, and symbol SNRs. It is found that smoothing is most beneficial for low symbol SNRs and low symbol rates. Smoothing gains up to 0.7 dB over sideband-aided residual carrier PLL, and the combined benefit of smoothing and sideband aiding relative to residual carrier loop is often in excess of 1 dB.     

Instrument Failure Detection in Partially Observable Systems

Instrument failure detection using the dedicated observer scheme (DOS) depends on partial state observability through each instrument which is monitored. For instrument fault detection by the DOS technique, a quantitative measure of partial state observability is established for each instrument and used to determine a necessary condition on the output structure of the system. This measure, called the internal redundancy of the instrument, indicates the complexity of the logic required for failure detection, and it also indicates where some hardware redundancy can be introduced into the system to improve the fault detection capability of the DOS. The principles developed are applied to a simulation of the pitch axis autopilot of the A7 jet aircraft.     

Adaptive Tracking Filter for Maneuvering Targets

A general method of continually restructuring an optimum Bayes-Kalman tracking filter is proposed by conceptualizing a growing tree of filters to maintain optimality on a target exhibiting maneuver variables. This tree concept is then constrained from growth by quantizing the continuously sensed maneuver variables and restricting these to a small value from which an average maneuver is calculated. Kalman filters are calculated and carried in parallel for each quantized variable. This constrained tree of several parallel Kalman filters demands only modest om; puter time, yet provides very good performance. This concept is implemented for a Doppler tracking system and the performance is compared to an extended Kalman filter. Simulation results are presented which show dramatic tracking improvement when using the adaptive tracking filter.     

A Closely Regulated TWT Converter

The design concept for the traveling wave tube amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics were utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power traveling wave tube (TWT), and at the same time operate at an efficiency of better than 90 percent from a 30-volt source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data is presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered. The circuit provides better than 0.5 percent regulation against load change, input voltage change, and over-operating temperature range of from -20 to + 80°C, with output ripple voltage of less than 2 volts peak-to-peak on top of the 3600-Vdc output. The measured efficiency was typically 87 percent. and recommendations are included to improve this to in excess of 90 percent.     

Target Identification by Natural Resonance Estimation

This paper presents a target identification method based on an estimation of the natural frequencies of oscillation in transient radar signatures. The emphasis is placed upon signal modeling and estimation ation strategy rather than relating resonance locations to physical structures. Salient features of this identification method are: 1) target aspect angle is not needed, 2) multiple targets of the same type can be illuminated simultaneously, and 3) bandpass interrogation ion pulses can be used. The latter feature is compatible with existing radar facilities. The method is applied to some simulated transfer functions, and factors affecting estimate accuracy are discussed.     

An exact expression for resolution cell area in special case ofbistatic radar systems

An exact expression for the bistatic resolution-cell area (A _B) is developed for the special case in which either the transmit or receive antenna has a broad azimuth beamwidth or is omnidirectional. Quantitative examples are presented to illustrate the variation of A_B with location. A comparison is made with the performance of a commonly used approximation formula     

Improved Switching Converter Model Using Discrete and Averaging Techniques

The nonlinear modeling and analysis of dc-dc converters has been done by averaging and discrete-sampling techniques. The averaging technique is simple, but inaccurate, as the modulation frequencies approach the theoretical limit of one-half the switching frequency. The discrete technique is accurate even at high frequencies, but is very complex and cumbersome. An improved model is developed by combining the aforementioned techniques. This new model is easy to implement in circuit and state variable forms and is accurate to the theoretical limit.