浅淡一种 VU 频段小型化机载全向高增益天线

文中提出了一款基于机载应用的变形套筒式天线,该天线具有全向辐射特性及高增益、小型化特点,天线剖面低,其外形具有良好的气动性,满足机载应用对天线高增益和低气动阻力的需要。天线高度小于0.17倍为最长工作波长;工作频段内电压驻波比小于等于3;110～250 MHz天线增益大于等于-3 dBi,250～550 MHz天线增益大于等于0 dBi;工作频段内不圆度小于等于±1.5 dB。     

自循环吸附动叶设计原理及数值模拟分析

研究了一种新型自循环吸附动叶,分析了其主要实现结构以及自循环吸附的原理。新型吸附结构利用动叶旋转离心作用形成的驱动力抑制了叶表分离、叶顶二次流动,增加了叶顶附面层动量,提高了动叶效率及稳定裕度。通过与传统的机匣处理技术的对比,阐明了自循环吸附动叶的独特结构以及叶顶喷气技术优势。以Rotor37动叶为例,依据基本的吸气、喷气原则,开展了吸气槽、叶顶喷气孔以及动叶内腔等自循环典型结构概念方案设计,突破了带有动叶内腔的复杂网格生成技术,完成了自循环吸附动叶内腔以及叶片通道内的流动分析以及特性分析。研究结果表明:自循环吸附技术优势明显,数值模拟证明其原理可行。     

基于绳系并联机器人支撑系统的SDM动导数试验可行性研究

详细给出了在低速风洞中,采用绳系并联机器人(WDPR)支撑模型,用强迫振荡法进行标准动态模型(SDM)动导数试验可行性的研究。试验中将杆式六分量应变天平内置入模型中以测量模型的气动力和气动力矩,建立了适用于绳系并联机器人支撑系统的模型运动控制子系统和数据采集子系统。采用绳拉力作为参考信号,对气动力矩信号与位姿信号进行数据的同步处理,解决了绳系并联机器人支撑系统应用于动导数试验时所测力矩信号与位姿信号之间的相位差确定问题,给出了WDPR支撑下模型动导数的计算方法。整个试验样机置于某开口式低速直流风洞中进行了俯仰、带偏航角的俯仰以及升沉的动导数试验,通过测量和计算得到各动导数。试验结果与参考文献相比较具有合理的一致性。研究结果表明,采用绳系并联机器人支撑模型进行动导数试验是可行的,至少对于SDM是这样的结果;使用一套绳系并联机器人支撑系统,可以完成多套硬式支撑系统才能完成的动导数试验,从而提高试验效率,降低试验成本。     

基于参数化分析的柔性后缘优化设计

介绍了一种自适应柔性机翼后缘变形控制优化设计方法,该方法采用了由单个驱动器驱动的单块式分布柔性结构。该方法的关键在于设计一种合适的柔性后缘结构拓扑形式,使该自适应柔性机翼后缘能够达到精确的变形。阐明了柔性结构拓扑优化设计的数学模型,针对自适应柔性机翼后缘概念设计提出了基于参数化分析的拓扑优化设计方案,并进行了工程化圆整和尺寸优化。最终,通过非线性有限元分析和功能测试,验证了本文提出的柔性后缘优化设计方法的合理性。     

Suggestion for aircraft flying qualities requirements of a short-range air combat mission

Owing to the lack of a direct link with the operations in short-range air combat,conventional aircraft flying qualities criteria are inappropriate to guide the design of a task-tailored flight control law.By applying the mission-oriented flying qualities evaluation approach,various aircraft with different control law parameters are evaluated on a ground-based simulator.This paper compares the evaluation results with several conventional flying qualities criteria,and discusses the appropriate parameter combination to reflect the flying qualities requirements of short-range air combat,The comparison and analysis show that a short-range air combat mission requires a higher minimum short period mode natural frequency and a smaller maximum roll mode time constant,and allows a lower minimum pitch attitude bandwidth and a higher maximum short period mode damp ratio than those of conventional flying qualities criteria.Furthermore,a combination of the pitch attitude bandwidth,the pitch attitude magnitude at the bandwidth frequency,and the pitch attitude transfer function gain can define the flying qualities requirements of short-range air com bat.The new metric can successfully predict the flying quality levels of aircraft in a short-range air combat mission.     

Nutation instability of spinning solid rocket motor spacecraft

The variation of mass,and moment of inertia of a spin-stabilized spacecraft leads to concern about the nutation instability.Here a careful analysis on the nutation instability is performed on a spacecraft propelled by solid rocket booster (SRB).The influences of specific solid propellant designs on transversal angular velocity are discussed.The results show that the typical SRB of End Burn suppresses the non-principal axial angular velocity.On the contrary,the frequently used SRB of Radial Burn could amplify the transversal angular velocity.The nutation instability caused by a design of Radial Burn could be remedied by the addition of End Burn at the same time based on the study of the combination design of both End Burn and Radial Burn.The analysis of the results proposes the design conception of how to control the nutation motion.The method is suitable to resolve the nutation instability of solid rocket motor with complex propellant patterns.     

Theoretical aspects of selecting repeated unit cell model in micromechanical analysis using displacement-based finite element method

Repeated Unit Cell(RUC)is a useful tool in micromechanical analysis of composites using Displacement-based Finite Element(DFE)method,and merely applying Periodic Displacement Boundary Conditions(PDBCs)to RUC is almost a standard practice to conduct such analysis.Two basic questions arising from this practice are whether Periodic Traction Boundary Conditions(PTBCs,also known as traction continuity conditions)are guaranteed and whether the solution is independent of selection of RUCs.This paper presents the theoretical aspects to tackle these questions,which unify the strong form,weak form and DFE method of the micromechanical problem together.Specifically,the solution’s independence of selection of RUCs is dealt with on the strong form side,PTBCs are derived from the weak form as natural boundary conditions,and the validity of merely applying PDBCs in micromechanical Finite Element(FE)analysis is proved by referring to its intrinsic connection to the strong form and weak form.Key points in the theoretical aspects are demonstrated by illustrative examples,and the merits of setting micromechanical FE analysis under the background of a clear theoretical framework are highlighted in the efficient selection of RUCs for Uni Directional(UD)fiber-reinforced composites.     

Transonic buffet control research with two types of shock control bump based on RAE2822 airfoil

Current research shows that the traditional shock control bump (SCB) can weaken the intensity of shock and better the transonic buffet performance.The author finds that when SCB is placed downstream of the shock,it can decrease the adverse pressure gradient.This may prevent the shock foot separation bubble to merge with the trailing edge separation and finally improve the buffet performance.Based on RAE2822 airfoil,two types of SCB are designed according to the two different mechanisms.By using Reynolds-averaged Navier-Stokes (RANS) and unsteady Reynolds-averaged Navier-Stokes (URANS) methods to analyze the properties of RAE2822 airfoil with and without SCB,the results show that the downstream SCB can better the buffet performance under a wide range of freestream Mach number and the steady aerodynamics characteristic is similar to that of RAE2822 airfoil.The traditional SCB can only weaken the intensity of the shock under the design condition.Under the off-design conditions,the SCB does not do much to or even worsen the buffet performance.Indeed,the use of backward bump can flatten the leeward side of the airfoil,and this is similar to the mechanism that supercritical airfoil can weaken the recompression of shock wave.     

电机变频控制实现换热器节能的应用研究

结合寒冷地区气候特点与通信机房温控的现状,针对50%浓度乙二醇溶液为工质的换热器,试验研究了自然冷源利用率与换热器自身变频节能的关系。结合乙二醇冷剂的特性,通过建立功率与频率关系模型、温差与功率和频率关系模型,实现了换热器循环泵和风机的变频控制策略。结果表明:在室内外温差、换热功率与循环泵、风机频率同时满足的条件下,以功率模型作为参数进行换热器自身的变频节能是可行的。通过对哈尔滨地区的气候数据与散热房控温试验分析,证明了乙二醇换热器的变频节能效果。     

拓扑优化方法在航空用钣金零件设计中的应用

为了满足航空产品高载重量及低耗油率的要求,采用拓扑优化技术对航空用钣金零件进行结构优化,实现了钣金零件强度高和重量轻的指标.案例分析表明,在航空用钣金零件初始设计阶段引入拓扑优化方法,会比设计过程中单纯使用结构尺寸优化和形状优化获得更大的经济效益.