飞行模拟器操纵负荷系统的无源性设计

 操纵负荷系统是飞行员与飞行模拟器之间的接口装置。提出了这种人在回路的实时控制系统的一种新的设计思想,这种设计将无源性与阻抗的概念结合,并将系统阻抗的频率特性作为定量设计的手段。基于频率分析,控制器设计中应增加一个阻尼项,使传递到操作员手上的阻抗与飞行环境的阻抗相匹配。并指出,系统中的力伺服系统的阻尼比应在0.5~0.8范围内以满足这个虚拟环境的无源性要求。操纵负荷系统的无源性可保证整个仿真系统的稳定性。所提出的设计思想还可推广应用于其他各种虚拟环境的设计。     

基于3D-PLM协同的航空复杂产品生命周期质量管理技术研究

目前我国航空复杂产品制造企业在PLM技术应用方面取得了一定的成果,在主机厂、所之间已经实现了基本的协同研制和生产,虽然这种协同模式未能包含诸如发动机和机载设备的供应商,但已在航空工业内部探索了价值链前端的部分协同,同时也开展了PLM多项目并行协同的数字化平台建设,这些都为基于3D-PLM协同的产品生命周期质量管理奠定了良好的基础。     

发动机进气道短舱前缘结冰三维模拟研究

为计算发动机进气道短舱前缘的结冰冰形,在Messinger结冰热力学模型的基础上发展了一套纯三维的表面溢流水流动结冰模型。考虑空气摩擦力为表面溢流水流动的主要驱动力,用空气对进气道表面的剪切力来确定溢流水的流动方向及流量分配。为求解溢流水结冰模型,发展了一套重复查找表面控制体状态的方法,能够快速完成整个三维表面的计算。用该方法对某三维发动机进气道进行计算,得到了三维结冰冰形,并将计算结果与FENSAP-ICE计算结果进行了对比,结果显示两者的冰形轮廓基本一致,仅在冰角处存在差异,表明本文三维发动机结冰计算模型与计算方法是有效的,其计算精度与FENSAP-ICE结果相当。     

Numerical investigation of the interaction between upstream cavity purge flow and main flow in low aspect ratio turbine cascade

In modern gas turbines, rim seal located between the stator-disc and rotor-disc is used to prevent hot-gas ingestion into the inner stage-gap of high pressure turbine. However, the purge flow supplied to the cavity through the rim seal interacts with the main flow, producing additional aerodynamic loss due to the mixing process which plays a significant role in the formation, development and evolution of downstream secondary flow. In this paper, a set of cascade representative of low aspect ratio turbine is selected to numerically investigate the influence of upstream cavity purge flow on the hub secondary flow structure and aerodynamic loss. Cascade with/without upstream cavity and four different purge mass flow rates are all taken into account in this simulation. Then, a deep insight into the loss mechanism of interaction between purge flow and main flow is gained. The results show that the presence of cavity and purge flow has a significant impact on the main flow which not only changes the vortex structure in both the passage and upstream cavity, but also alters the cascade exit flow angle distribution along the spanwise. Moreover, aerodynamic loss in the cascade rises with the increase of purge flow rate while the sealing effect is also enhanced. Therefore, the effect of upstream cavity purge flow must be considered in the process of turbine aerodynamic design. What is more, it is necessary to minimize the purge flow rate in order to reduce aerodynamic loss on the premise of satisfying cooling requirements.     

Nb-Si 基超高温合金的研究进展

Nb-Si基超高温合金由于熔点高、密度低和优良的高温强度等特点受到广泛关注,极具作为下一代高推重比航空发动机和超然冲压发动机的热端部件用材料的潜力.本文主要介绍了国内外在合金化、粉末冶金、定向凝固和热处理工艺对Nb-Si基合金组织和性能影响等方面的研究现状,并展望了其发展趋势.     

柔性SiO2 气凝胶的制备

以甲基三乙氧基硅烷为前驱体,通过溶胶-凝胶法和超临界干燥制备块状柔性SiO2气凝胶.研究了前驱体浓度对材料化学组成、微观结构及柔韧性、热稳定性的影响.结果表明,甲基的存在降低了分子网络的交联密度,赋予了材料柔韧性.随着前驱体浓度降低,微观结构中颗粒堆积紧密程度下降,材料的柔韧性增强;同时分子中硅羟基增多,热稳定性提高.     

高校体育行政管理信息系统的开发

介绍笔者开发的《高校体育行政管理信息系统》的基本特点、系统结构和主要功能，以及系统运行效果和应用前景。     

基于89C51的低速无线串行通信

在一些相对较复杂的单片机应用系统中,仅仅一个单片机资源是不够的,往往需要两个或多个单片机系统协同工作,论文介绍一种实现双机无线串行通信的方法。     

Experiments on film cooling with sonic injection into a supersonic flow

Film cooling experiments with sonic injection were conducted to investigate the effects of the number of the injection holes, the mass flow ratio, and the hole spacing on the film cooling effectiveness. The mainstream was obtained by the hydrogen-oxygen combustion, entering the experimental section at a Mach number of 2.0. The nitrogen with ambient temperature was injected into the experimental section at a sonic speed. The measured mainstream recovery temperature was approximately 910K. The mass flow ratio was regulated by varying the nitrogen injection pressure. The experimental results show that for the investigated cooling surface, the cooling effectiveness increases with the increase in the number of the injection holes with other parameters held constant. For a fixed cooling configuration, the cooling effectiveness increases with the increase in the mass flow ratio. Different from the subsonic film cooling, the optimal mass flow ratio is not observed. When the hole spacing is less than 4, no obvious difference is observed on the cooling effectiveness and lateral uniformity. With the mass flow ratio increasing further, this difference becomes much smaller. The shock wave also has an effect on the cooling effectiveness. Downstream the incident point of the shock wave, the cooling effectiveness is lower than that in the case without the shock wave.     

Active collision avoidance maneuver under constant thrust

In this paper, the relative position parameters of the target spacecraft are obtained by using the vision measurement and the target maneuver positions are calculated through the isochronous interpolation method. Furthermore, new switch control laws under constant thrust are designed for active collision avoidance maneuver of the chaser along a specified trajectory. The switch control laws are obtained based on the acceleration sequences and the working times of thrusters in three axes which can be respectively computed by the time series analysis method. The perturbations and fuel consumptions are addressed during the computation of the working times.