深空通信中码字复接结构Turbo译码器设计

码字复接结构Turbo译码器,有效解决了Turbo码与一些调制模块迭代级联时产生的信息损失问题,使得在调制迭代级联系统中,译码器能有效反馈包括信息位和校验位的全码字软信息.本文以与CPM调制级联系统为例,采用11种编码构造方案,分别对512,1024,2500码长的Turbo码方案进行对比.仿真结果表明,该方案较好地实...     

Microstructure and Magnetic Anisotropy of FeCoNbB Films

Effect of Nb contents on microstructure and magnetic properties of FeCoNbB films has been studied. X-ray diffraction (XRD) analysis reveals that Nb plays a role in refining grain and in facilitating formation of amorphous structure. When Nb content is more than 8 at%, the films transform from crystalline to amorphous structure, accompanied by variations in magnetic properties. An unusual out-of-plane anisotropy component is consequently observed. It can be suggested that the anisotropy induced by increasing Nb contents be attributed to stress-related magnetoelastic anisotropy. The undesirable anisotropy is greatly reduced by thermal annealing, reducing film thicknesses or applying an external magnetic field together with Si addition.     

基于新型涡轮冷却算法的航空发动机性能计算模型

针对气膜冷却和对流冷却两种常用的冷却方式,建立了新的涡轮冷却计算模型,并实现了与燃气涡轮发动机总体性能计算模型的耦合,得到了可考虑的不同冷却方式、适用于高涡轮前温度、大冷气量的燃气涡轮发动机总体性能计算模型,并与简化涡轮冷却模型的计算数据及试验数据作比较分析,表明新型涡轮冷却算法的可行性和能够提供更详细的涡轮部件气流参数.     

通用核心机涡轮气动设计准则

针对通用核心机对涡轮部件性能的要求,尝试给出了描述涡轮气动通用性的定义,研究了速度三角形系列参数对涡轮气动通用性的影响规律,在此基础上,得到了通用核心机涡轮部件气动设计参数选取准则,并通过S2和三维数值模拟手段,利用一组真实涡轮的数据对涡轮气动通用性的定义和设计参数选取准则进行了验证。结果表明:在涡轮设计参数选择中,存在使涡轮部件气动通用性最优的速度三角形参数范围;一般情况下气动设计参数在Ω=0.35～0.45,μ=1.65～1.9,K1=0.55～0.6区域内时,所设计的涡轮气动通用性较好;一系列涡轮气动设计参数的分析表明本文给出的涡轮部件气动通用性的定义和得到的涡轮部件气动设计参数选取准则基本合理。     

空间近程高速相对运动方程的状态转移矩阵

分析了空间近程高速相对运动的特点,建立了描述近程高速相对运动的线性微分方程组,并给出了状态转移矩阵与解析解。仿真结果表明:对于HEO-GEO近程高速相对运动,所建方程的相对距离计算误差仅为16 cm,不足Hill方程计算误差的15%。所给出的状态转移矩阵对于实现空间目标拦截等任务的实时高精度相对导航和制导算法具有一定的应用价值。     

抗高热流防静电涂层性能

研制了一种抗高热流防静电涂层,对涂层的抗高热流冲刷、防静电等性能进行了研究.经1.5、2.5、3.6、7.2 MW/m2短时(1 s)热流冲刷后,涂层无鼓泡、剥落,烧蚀前后体积电阻率均＜1×107Ω·cm,且具备一定的环境防护功能.     

基于PCC的航空机轮静载荷试验台控制系统研究

设计了一种基于PCC和工控机组成的航空机轮静载荷试验台控制系统,充分利用了PCC可靠性高、扩展性好等的优点,构建了一个性能稳定、功能强大的机轮载荷控制系统,有效提高了控制系统的自动化水平,大大降低了电气控制系统的复杂程度,使得航空机轮静载荷试验台控制系统能够可靠地完成机轮静态性能检测任务.     

A reflectance spectra-based approach to mapping salt fields using PCA-fused Landsat TM data

In this paper a method based on in situ measured reflectance spectra was developed for accurately mapping salt fields in the Taibei Salt Farm in Lianyungang City of East China. After radiometric correction and geometric rectification, six multispectral ETM+ bands were fused with the panchromatic band via principal components analysis (PCA). The fused data were used to map salt fields in the farm. Salt fields were mapped 91.95% correctly in comparison with ground statistics from raw multispectral bands. This accuracy level rose to 96.4% with the use of the panchromatic band (15 m resolution). However, PCA-fused data produced the highest accuracy of 98.8%. At the zone level, coarse resolution data resulted in an accuracy of 98.93% for crystallization ponds, but only 82.68% for condensation ponds. Use of the panchromatic band alone improved the accuracy for condensation ponds but decreased the accuracy for crystallization and evaporation ponds. Results derived from PCA-fused data are highly consistent with the ground statistics at a discrepancy between 0.35% for evaporation zone and 1.80% for condensation zone. It is concluded that a fine spectral resolution is important to separation of ponds of a varying salt content while a fine spatial resolution is important to their mapped area. Ponds of a lower salt content can be mapped more accurately from fused data than from raw spectral bands.     

HTPB和PET聚氨酯弹性体表面性质表征

采用接触角、衰减全反射-傅立叶变换红外光谱(ATR-FTIR)和SEM等表面表征技术研究了HTPB和PET聚氨酯弹性体的表面酸碱性质及表面状态信息.接触角结果表明,HTPB/TDI、HTPB/IPDI、PET(p)/N-100和PET(t)/N-100弹性体表面呈Lewis碱性,以PET与N-100反应得到的弹性体表面...     

焊接方法对5A06铝合金厚板焊缝接头性能的影响

分别采用搅拌摩擦焊(FSW)和熔化极氩弧焊(MIG)对20mm厚的5A06铝合金进行了焊接试验,对两种焊接方式的焊缝接头进行了机械性能测试、显微组织的观察以及表面残余应力的检测。结果表明,搅拌摩擦焊缝接头的抗拉强度比熔化极氩弧焊缝接头的高,搅拌摩擦焊缝接头往往断裂于前进侧的熔合过渡区,熔化极氩弧焊缝接头断裂于热影响区;相比熔化极氩弧焊,搅拌摩擦焊接头晶粒明显细化,焊缝中Mg、Mn等合金元素烧损明显减少,焊缝表面的残余应力水平也较低。