一种多功能训练器械设计与实训试验

针对以往特种运动器械存在设计理念陈旧、运动功能单一等缺陷,设计了一种能够提高受训人员综合身体素质的多功能训练器械。该器械主要由旋转中心框架、圆形中心框架、防护装置以及电动传动装置等组成,能够进行康复治疗、强化"核心"训练等。通过实际训练验证,该器械性能稳定,使用安全可靠,并且适用于多人施训,省时省力。     

测量船船摇前馈数据处理方法研究及应用

船摇前馈是航天测量船稳定性设计方法之一。实践证明,船摇前馈对改善系统误差有益,目标速度前馈特别是加速度前馈的改善效果要比船摇前馈的好。分析原因,一方面是目标相对船摇来说变化慢,低频分量多,滤波后能够比较准确地得到所要的值,前馈精度也就高;另一方面是船摇前馈值特别是加速度前馈比较难以准确获得。因此,准确地计算前馈量,是补偿测量设备伺服系统滞后造成的误差,达到高精度地跟踪目标的关键之一。本文详细给出了船摇前馈量的具体计算公式,并在卫星发射任务中进行了应用和验证。     

静电电荷量传感器标定技术研究

静电电荷量传感器在精密机械、航空发动机的状态监测、故障预测以及健康管理方面有着广泛应用。介绍了静电电荷量传感器的标定技术，基于油滴荷电的原理，结合直流高压源、支撑固定装置、电荷量测量装置研制了静电电荷量传感器标定系统。通过油滴实验，获得了油滴荷电量与施加电压、油滴大小、温湿度之间的关系，分析了影响标定装置的因素。     

铁基金刚石节块的热处理及其耐磨性能研究

首次提出了在烧结型金刚石工具的制造中引入热处理的新工艺，并系统地研究了淬火温度、淬火时间及回火温度等热处理工艺参数对热压烧结型铁基金刚石圆盘锯节块及其胎体材料机械性能的影响，同时对经热处理的铁基金刚石圆盘锯节块在石材旺苍红上进行磨损试验研究。试验结果表明，热压烧结型铁基金刚石圆盘锯节块胎体热处理的最佳工艺参数为：淬火温度为７６０～７９０℃、淬火时间为３．５ｍｉｎ、回火温度为２４５～３１５℃；经热处理后铁基金刚石圆盘锯胎体及节块的强度、硬度等机械性能有显著的提高，热处理也能明显改善铁基金刚石圆盘锯节块的耐磨性能。这说明将热处理工艺用于烧结型金刚石工具的制造中是切实可行的。     

水平表面气流剪切作用下的水膜厚度

飞机结冰表面上的液态水受气流吹拂作用会发生向后溢流,从而影响结冰区域范围及防冰系统设计;为了获得水膜流动规律,对水平平板表面上气流剪切驱动的水膜流动进行了实验测量和建模分析。通过水膜流动风洞试验台产生高速气流驱动水膜的流动,使用色散共焦位移计测量同一位置的水膜在不同时刻的厚度变化,结果表明气-液界面由底层薄水膜和多种尺度的波动组成,具有变化速度快随机性强的特点。通过水膜厚度随气流速度及水膜雷诺数的变化规律,发现平均水膜厚度与两者均呈现出单调非线性的依赖关系。基于薄水膜流动理论和平均水膜厚度实验结果,提出了高速气流剪切作用下的气-液波动界面剪切因子计算式,适用于风速17.8~52.2m/s,水膜雷诺数26~128之间的平板水膜流动计算。     

月面探测器月夜休眠自主唤醒方法

提出一种月面探测器休眠自主唤醒方法:月夜来临时通过地面控制对月面探测器所有设备进行休眠操作;月昼来临时靠太阳光触发唤醒功能,由休眠唤醒电路自主发送指令唤醒探测器,解决月面探测器安全可靠度过月夜的能源供给问题。该方法已通过在轨验证,可为其他深空探测任务提供参考。     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

Numerical study on flow fields and aerodynamics of tilt rotor aircraft in conversion mode based on embedded grid and actuator model

A method combining rotor actuator disk model and embedded grid technique is presented in this paper, aimed at predicting the flow fields and aerodynamic characteristics of tilt rotor aircraft in conversion mode more efficiently and effectively. In this method, rotor's influence is considered in terms of the momentum it impacts to the fluid around it; transformation matrixes among different coordinate systems are deduced to extend actuator method's utility to conversion mode flow fields' calculation. Meanwhile, an embedded grid system is designed, in which grids generated around fuselage and actuator disk are regarded as background grid and minor grid respectively, and a new method is presented for ‘donor searching' and ‘hole cutting' during grid assembling. Based on the above methods, flow fields of tilt rotor aircraft in conversion mode are simulated, with threedimensional Navier–Stokes equations discretized by a second-order upwind finite-volume scheme and an implicit lower–upper symmetric Gauss–Seidel(LU-SGS) time-stepping scheme. Numerical results demonstrate that the proposed CFD method is very effective in simulating the conversion mode flow fields of tilt rotor aircraft.