Cognitive performance aboard the life and microgravity spacelab

The impact of microgravity and other stressors on cognitive performance need to be quantified before long duration space flights are planned or attempted since countermeasures may be required. Four astronauts completed 38 sessions of a 20-minute battery of six cognitive performance tests on a laptop computer. Twenty-four sessions were preflight, 9 sessions were in-orbit, and 5 sessions were postflight. Mathematical models of learning were fit to each subject's preflight data for each of 14 dependent variables. Assuming continued improvement, expected values were generated from the models for in-orbit comparison. Using single subject designs, two subjects showed statistically significant in-orbit effects. One subject was degraded in two tests, the other was degraded in one test and exceeded performance expectations in another. Other subjects showed no statistically significant effects on the tests. The factors causing the deterioration in the two subjects can not be determined without appropriate ground-based control groups.     

Steady-state analysis of the constant-frequency clamped seriesresonant converter

A constant-frequency diode-clamped series resonant converter (CFCSRC) is proposed as a solution to problems associated with frequency-controlled resonant converters. This converter has two resonant frequencies, and control is achieved by varying the relative time spent at each switching frequency. Two zero-current-switching (ZCS) modes are examined and plotted in the output plane. An equation is given for the boundary between the two ZCS modes, as well as an expression for the boundary between ZCS and non-ZCS operation; both are plotted in the output plane. The output equation for the main mode is shown to be hyperbolic. Converter peak voltages limited to the input voltages, and peak currents are less than those of the frequency-controlled clamped series resonant converter over a large operating range. Data from a prototype converter are compared with theoretical data and are shown to be in good agreement with the theoretical model     

Exploiting GNSS signal structure to enhance observability

There are a number of different error sources, such as multipath and thermal noise, which corrupt satellite navigation waveforms from their theoretical structure. However, even under ideal conditions the broadcast signals have some degree of deformation as a result of the practical individual hardware implementation. For the most demanding users of satellite navigation, such as aircraft navigation and landing systems, it is important to characterize the nominal signal structure in order to detect minimal variations resulting from hardware-based errors. Thus far such precorrelation Global Navigation Satellite System (GNSS) signal quality monitoring has been performed through high gain antennas, which allow for raising the GNSS spectrum above the thermal noise floor and observing the structure of the signal directly at the front end output. This paper describes a new approach to achieve such observability based on signal processing techniques, such as dithering and averaging, which leverage the repetitive nature of the GNSS signal. The paper presents how these techniques can drastically improve the signal-to-noise ratio (SNR) in postprocessing, allowing for the direct analysis of GNSS signals using traditional front end designs and conventional antennas. Results are predicted using the appropriate theory and validated using data collected from the Global Positioning System (GPS).     

Power management and distribution system for a more-electricaircraft (MADMEL)

A five-phase Power Management and Distribution System for a More-Electric Aircraft (MADMEL) program was awarded by the Air Force to Northrop/Grumman Military Aircraft Division in September 1991. The objective of the program is to design, develop, and demonstrate an advanced electrical power generation and distribution system for a More-Electric Aircraft (MEA). The MEA emphasizes the use of electrical power in place of hydraulics, pneumatic, and mechanical power to optimize the performance and life cycle cost of the aircraft. This paper presents an overview of the MADMEL program and a top-level summary of the program results, development and test of major components to date. In Phase I and Phase II studies, the electrical load requirements were established and the electrical power system architecture was defined for both near-term (NT-year 1996) and far-term (FT-year 2003) MEA application. The detailed design and specification for the Electrical Power System (EPS), its interface with the Vehicle Management System, and the test set-up were developed under Phase III. Phase IV, fabrication and testing of the subsystem level hardware, has been completed. Overall system level integration and testing, Phase V, is scheduled to be completed by September 1999