Selective laser melting of Al–8.5Fe–1.3V–1.7Si alloy: Investigation on the resultant microstructure and hardness

This article presents the microstructure and hardness variation of an Al–8.5Fe–1.3V–1.7Si(wt%, FVS0812) alloy after selective laser melting(SLM) modification. Three zones were distinguished across the melting pool of the SLM-processed FVS0812 alloy: the laser melted zone(LMZ), the melting pool border, and the heat affected zone(HAZ) in the previously deposited area around the melting pool. Inside the LMZ, either an extremely fine cellular-dendritic structure or a mixture zone of the a-Al matrix and nanoscale Al_(12)(Fe,V)_3Si particles appeared. With a decreased laser beam scanning speed, the cellular-dendritic structure zone within the LMZ shrank significantly while the mixture zone expanded. The a-Al and Al_(12)(Fe,V)_3Si mixture zone was also observed in the HAZ, but another phase, submicron h-Al_(13)Fe_4 particles with rectangular or hexagonal shapes,formed along the melting pool border. Microhardness tests indicated that the hardness of the SLM-processed FVS0812 samples far exceeded that of the as-cast FVS0812 alloy.     

自适应天线抗干扰性能研究

分析了适用于雷达抗干扰的一些自适应天线波束形成算法,将子空间正交投影算法应用于雷达抗干扰,针对子空间分解过程中特征向量不能完全正交的问题,采用约束化子空间分解算法,来保证子空间特征向量的正交性.最后通过仿真证明:子空间跟踪算法相对于传统的一些自适应算法具有更强的抗干扰性能.     

Investigations into sensing characteristics of circular thin-plate electrostatic sensors for gas path monitoring

Circular thin-plate electrostatic sensors are promising in gas path monitoring due to their advantages of non-intrusiveness and easy installation. The spatial sensitivity and filtering effect are two important performance parameters. In this paper, an analytically mathematical model of induced charge on a circular thin-plate electrode is first derived. Then the spatial sensitivity and filtering effect of the circular electrostatic sensor are investigated by numerical calculations. Finally,experimental studies are performed to testify the theoretical results. Both theoretical and experimental results demonstrate that circular thin-plate electrostatic sensors act as a low-pass filter in the spatial frequency domain, and both the spatial filtering effect and the temporal frequency response characteristics depend strongly on the spatial position and velocity of the charged particle. These conclusions can provide guidelines for the optimal design of circular thin-plate electrostatic sensors.     

平面工艺功率型半导体晶体管铝迁移实验

在平面工艺制造的功率型半导体晶体管芯片表面,发现高强度电场条件下存在跨越0.05 mm半绝缘硅带的铝迁移现象,对此开展了一系列实验研究. 通过开帽物理观察与分析、低温测试与烘干验证、迁移物质分析对比,确定了迁移现象中的迁移物质,同时分别取证环境温度、湿度、芯片表面污染物以及器件局部结构与此迁移现象的关联性,以此提出了迁移机理假说,为在不同的诱发条件下对此迁移机理进行确认和量化研究提供指导.      

航天器机械臂柔性力控辅助装配方法

文章从装配的实际需求出发,提出一种航天器机械臂柔性力控辅助装配方法:通过在机械臂末端法兰与负载之间安装的六维力传感器感知作用力与力矩信息,人手直接作用于机械臂末端的负载,系统通过负载的重力补偿算法获得人手作用的力与力矩信息,而后以力/力矩信息作为输入来控制机械臂进行移动或转动,使负载柔性跟随人手运动。文章给出了装配方法的详细设计方案与相关算法,并进行了初步试验验证。试验表明,该装配方法可以有效提高在航天器狭小空间内进行大重量工件安装的效率,且安全可靠。     

计算机辅助机械设计的实践与研究

本文结合作者编制计算机辅助机械设计课程设计应用软件的经验，介绍了机械设计中计算机应用程序的构造、流程和数据处理方法，这些方法适用于计算量大、数据量多的设计过程。     

Single track and single layer formation in selective laser melting of niobium solid solution alloy

Selective laser melting (SLM) was employed to fabricate Nb-37Ti-13Cr-2Al-1Si (at%) alloy, using pre-alloyed powders prepared by plasma rotating electrode processing (PREP). A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance. Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density (LED), i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLM-processing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys.     

Training effectiveness evaluation of helicopter emergency relief based on virtual simulation

Helicopters are playing an increasingly important part in emergency relief, such as earthquake rescue, firefighting and medical transport. With the development of virtual simulation technology, virtual simulation-based training is widely used in the training of the helicopter crew especially for the dangerous and costly missions mentioned above. A complete training effectiveness evaluation method is proposed to evaluate the trainees’ training effect based on virtual simulation in this paper. A key to this method is regarding the complicated process as a discrete event-activity flow system and establishing the evaluation indicator system. Then expert group and Analytical Network Process (ANP) are applied to determine the weight of indicators. When the training data are processed, there is a novel attempt to apply Fuzzy Comprehensive Evaluation (FCE) model to calculate the two categories of indicators. Eventually, an experiment and the analysis were carried out to validate the evaluation method.     

增强FMS柔性的关键技术研究

柔性制造技术是现代制造业广泛采用的一种先进的制造技术。实现生产柔性是引进柔性制造技术的根本目的。ＦＭＳ是柔性制造技术应用的典型模式。     

试论现代图书馆开展网络资源导航服务

计算机科学技术飞速发展,网络资源丰富杂乱,纸质资源捉襟见肘,通过阐述现代图书馆开展网络资源导航的必要性和可能性,找到现代图书馆的定位和方向,最后阐述现代图书馆开展网络资源导航的意义和价值。