收发分置雷达定位模型及精度仿真

针对收发分置雷达探测目标的特点,建立了收发分置雷达的目标定位模型,并且对收发分置雷达的目标定位精度进行了仿真和分析,重点讨论了目标参数的变化对定位误差分布的影响,得出了有用的结论,最后指出了研究内容在雷达组网作战中的应用前景.     

Crack monitoring method based on Cu coating sensor and electrical potential technique for metal structure

Advanced crack monitoring technique is the cornerstone of aircraft structural health monitoring.To achieve real-time crack monitoring of aircraft metal structures in the course of service,a new crack monitoring method is proposed based on Cu coating sensor and electrical potential difference principle.Firstly,insulation treatment process was used to prepare a dielectric layer on structural substrate,such as an anodizing layer on 2A12-T4 aluminum alloy substrate,and then a Cu coating crack monitoring sensor was deposited on the structure fatigue critical parts by pulsed bias arc ion plating technology.Secondly,the damage consistency of the Cu coating sensor and2A12-T4 aluminum alloy substrate was investigated by static tensile experiment and fatigue test.The results show that strain values of the coating sensor and the 2A12-T4 aluminum alloy substrate measured by strain gauges are highly coincident in static tensile experiment and the sensor has excellent fatigue damage consistency with the substrate.Thirdly,the fatigue performance discrepancy between samples with the coating sensor and original samples was investigated.The result shows that there is no obvious negative influence on the fatigue performance of the 2A12-T4 aluminum alloy after preparing the Cu coating sensor on its surface.Finally,crack monitoring experiment was carried out with the Cu coating sensor.The experimental results indicate that the sensor is sensitive to crack,and crack origination and propagation can be monitored effectively through analyzing the change of electrical potential values of the coating sensor.     

航空发动机维修技术进展与展望

航空发动机是为航空装备提供动力的装置,维修保障是保障发动机完成服役周期的重要阶段。随着航空发动机维修产业的不断发展,为满足未来大批量、高质量、高效率的维修需求,发动机维修技术也在不断提升和发展。本文简要介绍了航空发动机维修发展历史;从故障检查、整机清洗和整机装配三个方面综述了航空发动机整机维修技术的研究进展,从再制造发展、关键技术和技术开发流程三个方面阐述了航空发动机再制造进展;并对航空发动机维修和再制造技术的未来发展进行了展望。     

固体火箭喷管颗粒尺寸分级两相跨音速流场计算

本文中对固体火箭喷管颗粒尺寸分级的两相跨音速流场作了计算.气相控制方程采用隐式近似因子分解法求解,尺寸分级的颗粒控制方程采用特征线求解,然后,二者进行充分的耦合,可以获得固体火箭发动机含有任意颗粒质量分数和不同颗粒尺寸时轴对称喷管跨音速流场的参数分布.文中讨论了不同颗粒半径和质量分数对流场的影响,对单一颗粒尺寸和颗粒尺寸分级的参数进行了比较.两相耦合计算的迭代收敛速度取决于气相,本文中气相方程求解的格式除部分边界外是隐式的,CFL数可取至6左右,收敛速度快.特别是对颗粒尺寸分级的计算,得益更大,其得益的倍数为颗粒的分级数.     

GAP／AN推进剂的应用与研制进展

概述了ＧＡＰ／ＡＮ推进剂的特性，研制状况及发展潜力，针对目前该推进剂的各项性能水平（能量性能，燃烧性能，力学性能）提出了该推进剂存在的问题及改善方法。     

Dispersion-free quantum clock synchronization via fiber link

We proposed a fiber-based quantum clock synchronization protocol by employing the dispersion cancellation feature of the frequency anti-correlated entangled source under the quantum interference measurement. It is shown that, the accuracy of the synchronization is mainly dependent on the bandwidth of the frequency entangled biphoton spectrum and on the temperature variation induced fluctuations in both the reference fiber coiling and the fiber link. With this proposal, synchronization between two clocks at a distance of ten kilometers can be implemented with an accuracy below a picosecond.     

先进复杂产品研制体系的分析

针对新时期大型复杂装备的研制特点,通过对先进设计技术的跟踪研究,分析国外复杂产品装备研制的先进设计技术、理论和方法,并结合典型应用案例深入研究先进设计技术在复杂产品研制中的应用,以帮助我国军工制造企业更好地理解和应用先进的综合设计技术。     

COMPASS/GPS双系统四星定位算法研究

针对COMPASS系统处于组网期,有效卫星缺失引起双系统卫星导航接收机暂时性无法定位的问题,提出一种双系统四星定位算法。利用完备条件下的定位信息,采用最小二乘拟合法或α-β滤波法,将完备条件下解算得到的COMPASS与GPS的系统钟差线性化,得到该钟差在非完备条件下的值,再结合可视卫星,在双系统四星条件下短时间内保持定位。算法无需引入其他设备,不依赖电子地图。经仿真验证,算法有效可行,在双系统四星条件下定位精度较高,且卫星信号恢复到完备条件后,定位精度能迅速恢复到完备条件下的水平。     

SAR欺骗干扰工程化设计研究

对SAR雷达的欺骗干扰研究在理论模型方面已经有了大量深入的研究,但对该领域在工程化设计方面的研究报道很少.首先给出了SAR欺骗干扰机的系统组成,然后分析了大数据量卷积模块的分段分相流水处理方法.在此基础上,给出了DRFM模块的硬件实现方案.结合硬件,提出了一种简单有效的闭环等效验证方法,并采集实际数据做了验证试验.试验效果证明了该硬件方案的有效性.最后,分析了SAR欺骗干扰机走向实用化所需的进一步研究的内容和方向.