Extension of the low diffusion particle method for near-continuum two-phase flow simulations

The low diffusion (LD) particle method, proposed by Burt and Boyd, is modified for the near-continuum two-phase flow simulations. The LD method has the advantages of easily coupling with the direct simulation Monte Carlo (DSMC) method for multi-scale flow simulations and dramatically reducing the numerical diffusion error and statistical scatter of the equilibrium particle methods. Liquidor solid-phase particles are introduced in the LD method. Their velocity and temperature updating are respectively, calculated from the motion equation and the temperature equation according to the local gas properties. Coupling effects from condensed phase to gas phase are modeled as momentum and energy sources, which are respectively, equal to the negative values of the total momentum and energy increase in liquid or solid phase. The modified method is compared with theoretical results for unsteady flows, and good agreements are obtained to indicate the reliability of the one-way gas-to-particle coupling models. Hybrid LD-DSMC algorithm is implemented and performed for nozzle discharging gas-liquid flow to show the prospect of the LD-DSMC scheme for multi-scale two-phase flow simulations.     

FM73M 胶膜及其与PMI 泡沫芯的胶接机理

采用DSC研究了不同升温速率下FM73M胶膜的固化反应特性,根据DSC曲线得到了胶膜的凝胶化温度和固化温度等工艺参数,建立了其固化动力学模型,确定胶膜的固化参数为(125±2)℃/90min.在此基础上,通过SEM研究了胶膜在PMI泡沫芯材内的分布以及界面结合状况(界面润温情况、气孔、缺陷),分析了胶膜与泡沫芯的胶接机理.     

复合材料螺栓连接失效的数值模拟

作为一种重要的连接及承载形式,复合材料螺栓的连接性能直接影响到结构组件的承载可靠性.本文针对复合材料各向异性及渐进损伤特点,建立了包含复合材料螺栓及复合材料板的有限元模型.通过编制U-Mat程序,利用ABAQUS商用软件对复合材科螺栓连接的失效过程进行了数值模拟,得到了连接件的载荷-位移曲线,并对连接件的失效模式进行了分析.     

Non-destructive Evaluation of Absolute Stress in Steel Members Using Shear-Wave Spectroscopy

Non-destructive measurement of absolute stress in steel members can provide useful information to optimize the design of steel structures and allow the safety of existing structures to be evaluated.This paper investigates the non-destructive capability of ultrasonic shear-wave spectroscopy in absolute stress evaluation of steel members.The effect of steel-member stress on the shear-wave amplitude spectrum is investigated,and a method of absolute stress measurement is proposed.Specifically,the process for evaluating absolute stress using shear-wave spectroscopy is summarized.Two steel members are employed to investigate the relationship between the stress and the frequency in shear-wave echo amplitude spectrum.The H-beam loaded by the universal testing machine is evaluated by the proposed method and the traditional strain gauge method for verification.The results show that the proposed method is effective and accurate for determining absolute stress in steel members.     

Inertial aided BDS triple-frequency integer ambiguity rounding method

The integer ambiguity resolution (AR) of carrier phase is significant for Global Navigation Satellite System (GNSS) precise positioning. However, in kinematic case, single-epoch AR methods based on alone GNSS are usually not reliable due to the instable pseudorange accuracy. Moreover, the computation of classical AR method Least Squares Ambiguity Decorrelation Adjustment (LAMBDA) is large. Thus, the inertial measurement unit (IMU) is introduced, a new inertial-aided AR method that directly rounds the float ambiguity of BeiDou triple-frequency combined observations, which is characterized by long wavelength, low carrier-phase noise and ionospheric delay, is proposed. The mathematical model of the new method is derived first. Then the impacts of the carrier-phase noise, ionospheric delay and inertial navigation system (INS) position error on the AR success ratio of combined observation are analyzed through probabilistic approach. Based on above investigation, the combinations (0, ?1, 1), (1, 4, ?5) and (4, ?2, ?3) are selected to resolve the original ambiguity. A vehicular integrated navigation test is performed to demonstrate the proposed method. The results show that the average AR success ratios of the three selected combinations, whose float ambiguity errors are 0.041, 0.146, 0.279 cycle respectively, are above 97.25% without regard to low-elevation C05. With respect to positioning accuracy based on our AR method when compared with IE software, the east, north, up error RMS of position are 0.042, 0.024, 0.069 m, respectively. In terms of the AR recover after the BeiDou signals outage, as long as 62 s BeiDou signal complete outage, all the ambiguities of all satellites could be re-fixed immediately. Besides, during the 90 s signals partial outage, the AR is not influenced by the position error, since the float ambiguity errors are all below half-cycle. The research of this contribution demonstrates the effectiveness of the proposed new method, which indicates it is applicable to kinematic positioning, even in BDS degraded and denied environments.     

风云二号卫星地面控制系统自适应同步控制方法

针对风云二号07星测控实施过程中部分姿章联控参数未能正常执行的系统间时序控制不同步问题,研究提出一种地面控制系统自适应同步控制方法,分析卫星历史数据得到有效接收时间区间,取所有有效接收时间区间的交集得到最终有效接收时间区间。经验证,方法可有效解决系统间时序不同步的问题,精度高,控制效果好。     

Hierarchical scheduling for real-time agile satellite task scheduling in a dynamic environment

The imaging processes of optical satellites can be easily affected by unexpected environmental changes, such as changes in cloud coverage. Given the difficulty to predict environmental uncertainties, traditional offline scheduling methods need a follow-up re-scheduling process that responds to real-time environmental information. This repetitive scheduling processes make the offline fine scheduling process a waste of computational resources. Additionally, the offline scheduling method is quite complex owing to its lack of a hierarchy mechanism. To solve these problems, we propose a hierarchical scheduling method for the real-time scheduling problem. This method divides the scheduling process into three steps: pre-assignment, rough scheduling, and fine scheduling. A hierarchical scheduling algorithm based on ant colony algorithm is proposed. Tests with 36 scenarios show that the calculation time is efficiently reduced with this new mechanism. With this consideration of the dynamic environment, the re-scheduling process becomes unnecessary, meaning the wasting of computational resources is avoided and the solution profit is improved.     

基于有限元3-RPS并联机床轻量化优化设计

为了减轻3-RPS并联机床质量,提高其刚度,分别对静平台与支链进行了结构改进.采用连接单元模拟机床中运动副,对并联机床静刚度进行有限元分析.通过分析结果获得静平台的刚度薄弱环节、支链的变形及其对机床变形的影响规律.在静平台刚度薄弱处增加抵抗变形的筋板,并通过减小其框架尺寸的方式优化静平台结构.采用悬臂梁模型分析支链的变形,以支链质量和变形乘积最小对支链进行尺寸优化.改进后的并联机床质量显著减轻,机床变形明显减小.优化结果能够提高机床动态响应性能以及机床精度.     

连续短线段空间圆弧转接与插补

针对连续短线段高速加工控制需求,研究了利用空间圆弧转接实现高速插补的方法。建立了圆弧转接数学模型,研究了转接的几何约束和运动约束、转接参数计算、空间圆弧插补等相关理论与算法,并详细分析了算法的使用范围、效率制约因素和计算量等工程实现相关问题。仿真和加工实验表明:该转接算法能显著提高加工效率,减小振动,改善工件表面质量。作为空间圆弧转接算法基础的空间圆弧插补算法对空间任意平面内圆弧插补具有实用价值。本文所有算法已经在自主研发的数控平台上进行了验证,应用效果良好。     

分隔板形式对多爆震管间相互作用的影响分析

为研究共用喷管多爆震管间爆震流场的相互作用,以氢气和氧气混合物为例,对采用不同形式分隔板的共用喷管多爆震管间的相互作用过程进行了数值模拟,并对其性能进行了比较与分析。计算结果表明,采用斜分隔板能有效地减小多爆震管间的相互影响,并且加长分隔板长度可以进一步减小多爆震管间的相互影响,同时还可以通过控制分隔板的长度来控制折射激波到达上爆震管封闭端的时间。