基于经纬仪的光束平差法定向方法改进

针对基于传统经纬仪工业测量系统使用光束平差法定向精度有待提高的问题，提出一种新的定向改进方法。该方法同时结合了精确互瞄法与光束平差法，简化了测量过程，提出新的约束，消减了光束平差法中定向阶段的基准点测量累积误差，实现了在非通视条件中完成多台经纬仪高精度定向的目标。试验数据表明：该方法可在10m范围内，在误差为±3″的测点交会精度下，维持0.1mm的定向精度。     

丁腈橡胶增韧环氧树脂基烧蚀防热材料性能

以丁腈橡胶(CTBN)为增韧剂对环氧树脂(F51)进行增韧改性,通过FTIR、TG以及力学性能测试研究了丁腈橡胶对环氧树脂固化反应、热稳定性能和力学性能的影响,并分析了其增韧机理;分别采用燃气流剪切烧蚀试验和电弧风动烧蚀实验考核了低密度烧蚀材料的烧蚀性能。结果表明:经CTBN改性后,两者的分子链产生了一定程度的交联;树脂基体的拉伸、弯曲性能有所下降,但韧性得到了增强;热稳定性大大提高,增韧后的F51树脂在800℃时的残重率由增韧前的23%提高到了54%;低密度烧蚀材料的抗剪切、抗剥蚀能力得到了增强,且碳层的尺寸稳定性也得到了改善,烧蚀性能提高。     

硅半球深腔结构无损检测技术

半球深腔的加工质量是决定硅基MEMS半球陀螺精度的关键因素之一，及时检测半球深腔的形貌参数并将其反馈至加工过程，是确保高性能MEMS半球陀螺研制成功的重要措施。由于硅半球深腔的深度较大，台阶仪和光学显微成像系统无法对半球深腔的形貌特征进行有效测量。因此,需要将硅深腔结构剖开后采用扫描电镜(SEM)进行检测。这种检测方式时间周期长，且属于破坏性的样本检测，效率和测试精度都较低。提出以硅半球深腔为模具，利用PDMS铸模将硅半球深腔的结构尺寸和表面形貌转移到PDMS凸起的半球模型上，通过检测PDMS半球模型的尺寸结构和表面形貌，即可反推出硅半球深腔的尺寸特征。经实验验证，脱模后的PDMS模型可以准确地反映出半球深腔的尺寸信息，测量结果的不确定度小于5‰，有效解决了硅半球深腔无损检测的难题。     

低速大转矩永磁游标电机在发酵罐中的应用

采用秸秆生产丁醇时,为了达到高效率发酵,需要使发酵液中菌体分布均匀,所加物料需要及时搅拌。工业化生产丁醇的发酵罐尺寸较大,搅拌过程对驱动电机的输出转矩要求较高,因此高效率、小体积、低速大转矩的秸秆发酵搅拌电机对工业化发酵生产丁醇意义重大。设计了一种定转子永磁游标电机用于发酵液搅拌,并对电机的槽极数、电磁性能进行了具体的研究。制造样机并采用滞环控制实现了对液态发酵对象的快速响应,且实现了低能耗、高效率的发酵过程。     

基于ANSYS Workbench的行星滚柱丝杠动态特性分析

通过Pro/Engineer建立行星滚柱丝杠三维模型，基于ANSYS Workbench有限元分析技术进行模态与谐响应分析，得到前六阶固有频率与各阶模态振型，确定共振频率，掌握对应频率下的位移峰值响应，并研究螺母处于不同工作位置时对固有频率的影响，为基于行星滚柱丝杠传动的舵系统抗振设计提供数据支撑。     

Availability modeling for periodically inspection system with different lifetime and repair-time distribution

Availability is a main feature of design and operation of all engineering system. Recently,availability evaluation of periodical inspection systems with different structures is at the center of attention due to the wide application in engineering. In this paper, an analytical and probabilistic availability model for periodical inspection system is proposed by a new recursively algorithm,which can achieve limiting average availability and instantaneous availability of periodical inspection system under arbitrary lifetime and repair-time distributions. Then three application examples are presented, the systems lifetime and repair-time are respectively fellow exponential/exponential,Weibull/normal and Weibull/lognormal distribution. Finally, a Weibull/lognormal system is studied to analyze the dynamic relationship between inspection period and availability. The results indicate that the proposed approach can provide the technology support for improving system availability and determining reasonable inspection period.     

Aircraft nonlinear stability analysis and multidimensional stability region estimation under icing conditions

Icing is one of the crucial factors that could pose great threat to flight safety,and thus research on stability and stability region of aircraft safety under icing conditions is significant for control and flight.Nonlinear dynamical equations and models of aerodynamic coefficients of an air craft are set up in this paper to study the stability and stability region of the aircraft under an icing condition.Firstly,the equilibrium points of the iced aircraft system are calculated and analyzed based on the theory of differential equation stability.Secondly,according to the correlation theory about equilibrium points and the stability region,this paper estimates the multidimensional stability region of the aircraft,based on which the stability regions before and after icing are compared.Finally,the results are confirmed by the time history analysis.The results can give a reference for stability analysis and envelope protection of the nonlinear system of an iced aircraft.     

阵风载荷减缓系统故障分析

阵风引起的额外载荷会引起飞机结构疲劳,降低结构使用寿命。采用非定常气动力有理函数拟合方法建立时域状态空间下的动力学系统,设计了阵风载荷减缓系统。研究了阵风载荷减缓系统3种典型故障模式(副翼偏转饱和、舵机卡死、副翼偏转延时)的力学建模方法,并对机翼在阵风减缓系统故障模式下的阵风响应进行分析。仿真结果表明,3种故障模式均不利于阵风载荷减缓系统对阵风载荷的减缓,对于一些特定情况,故障模式下的阵风载荷减缓系统不仅不能减缓阵风载荷,还会带来由副翼偏转不当引起的额外负载。     

EPDM包覆层热解状态下的力学行为及本构模型

为了准确描述固体火箭发动机三元乙丙(EPDM)包覆层在不同热解状态下的力学特性,通过热重分析的方法得到EPDM的热解温度范围,并采用准静态单轴拉伸实验的方法获得EPDM在不同热解温度下的应力-应变曲线。以Ogden(n=2)模型为基础,分别对不同热解状态下的力学曲线进行建模,并通过对实验数据的拟合获得模型参数。结果表明,在初始热解状态下,材料只发生了少量的失水和气体的逃逸,其力学行为可通过粘超弹本构模型进行描述;随着材料热解程度增加,基体材料和填充纤维均遭到破坏,其力学行为表现为超弹脆性材料特性。