基于有限元法的无刷交流励磁机空载特性分析及额定励磁电流计算

针对无刷交流励磁机铁心结构的复杂性和铁磁材料饱和特性的影响,采用非线性有限元法,利用有限元软件Maxwell,建立无刷交流励磁机的二维模型,对空载特性及额定励磁电流进行研究分析。以1台28 kW无刷交流励磁机为例,对电机气隙磁场仿真分析并求取空载特性。计算所得的基波电势与实测结果相符,为此类电机电磁场的设计提供理论依据。在此基础上通过场路耦合的方法,用外电路来模拟额定负载工况,计算出额定工况下的励磁电流。该方法具有实用性,可为一般的交流励磁机励磁电流计算提供参考。     

电动汽车用永磁同步电机控制器设计

电动汽车逐渐成为人们出行的交通工具之一,对技术可靠性和安全性的要求较高。电机控制器是实现电池直流电源向三相交流电源转换的装置,驱动永磁同步电机(PMSM)输出力能。设计了一款基于瑞萨单片机的PMSM控制器,从元器件选型、硬件保护电路原理、PCB布局、控制算法、结构强度和热分析方面展开分析。最后生产控制器样机并搭建试验平台,对PMSM控制器进行了效率特性测试、发电测试和温升测试。试验结果验证了设计方案的合理性。     

Effect of W addition on phase transformation and microstructure of powder metallurgic Ti-22Al-25Nb alloys during quenching and furnace cooling

Powder metallurgic Ti2 AlNb alloys with W addition are sintered at 900, 1000, 1070 °C,and 1150 °C(i.e., in the O + B2, a_2+ B2 + O, a_2+ B2, and single B2 phase regions, respectively)for 12 h, followed by water quenching and furnace cooling. Comparisons of phase and microstructure between quenched and furnace-cooled W-modified alloys are carried out to illustrate the phase transformation and microstructure evolution during the cooling process. Furthermore, a comparison is also made between W-modified and W-free alloys, to reveal the function of the W alloying.W addition accelerates the solutions of a_2 and O phases during the high-temperature holding, and a Widmannsta¨tten B2 + O structure, which contributes to the properties, is induced by furnace cooling from all the phase regions. The Widmannsta¨tten structure includes a B2 matrix, primary O, and secondary O precipitates. However, W alloying refines the Widmannsta¨tten structure only when the alloys are solution-treated and then cooled from the single B2 phase. Although the hardness of the W-modified alloys is lower than that of the W-free alloys sintered in the same phase region, an enhancement of hardness, 489 ± 18 HV, is obtained in the alloy solution-treated in the single B2 phase region for only 0.5 h.     

基于功率保持的辅助动力装置引气性能计算模型

以带负载压气机辅助动力装置(APU)为对象,分析了其结构特点与工作原理,针对目前工程上常用的APU引气性能计算模型的不足,建立了基于APU与空气涡轮匹配的总体性能数学模型和负载压气机变几何部件特性插值模型。在此基础上,研究了APU功率调节规律,获得了轴功率负载、APU涡轮前温度、排气温度与负载压气机进口导叶角度之间的匹配关系,进而实现了APU全包线内和全工况下的引气性能计算。利用GTCP131-9A试验数据对模型进行了验证,结果表明:引气流量计算误差小于3%,引气压力计算误差小于4%;功率保持下的APU涡轮前温度限制值仅与轴功率负载大小有关,与进气温度无关。研究结论对于带负载压气机APU总体性能计算和调节规律设计提供了参考。      

Event-triggered adaptive control for attitude tracking of spacecraft

Plug-and-play technology is an important direction for future development of spacecraft and how to design controllers with less communication burden and satisfactory performance is of great importance for plug-and-play spacecraft. Considering attitude tracking of such spacecraft with unknown inertial parameters and unknown disturbances, an event-triggered adaptive backstepping controller is designed in this paper. Particularly, a switching threshold strategy is employed to design the event-triggering mechanism. By introducing a new linear time-varying model, a smooth function, an integrable auxiliary signal and a bound estimation approach, the impacts of the network-induced error and the disturbances are effectively compensated for and Zeno phenomenon is successfully avoided. It is shown that all signals of the closed-loop system are globally uniformly bounded and both the attitude tracking error and the angular velocity tracking error converge to zero. Compared with conventional control schemes, the proposed scheme significantly reduces the communication burden while providing stable and accurate response for attitude maneuvers. Simulation results are presented to illustrate the effectiveness of the proposed scheme.     

A survey on numerical simulations of drag and heat reduction mechanism in supersonic/hypersonic flows

Along with the survey on experimental investigations drawing attention to the drag and heat reduction mechanism, the authors simultaneously focus on the recent advances of numerical simulations on the schemes applied to supersonic/hypersonic vehicles. The CFD study has evolved as an irreplaceable method in scheme evaluation and aircraft optimization. Similar to our previous experimental survey, the advances in drag and heat reduction schemes are reviewed by similar kinds of mechanism in this article, namely the forward-facing cavity, the opposing jet, the aerospike, the energy deposition and their combinational configurations. This review article puts an emphatic eye on the flow conditions, numerical methods, novel schemes and analytical conclusions given in the simulations. Further, the multi-objective design optimization concept has also been illustrated due to the observable advantages of using CFD over experimental method, especially those performances conducted in drag reduction and thermal protection practice, and this would possess reference value in the design of aircraft system.     

一种用于纳米颗粒场致发射推力器的自中和技术

纳米颗粒场致发射推力器(NFET)是一种用于微小卫星的固体工质静电推力器,为促进NFET的工程研制,提出一种新的自中和技术——反向充电中和策略。为研究这种自中和技术的设计方法,建立相应的数值模型以模拟该中和技术下羽流输运过程,并且,在真空舱中开展NFET的羽流测量试验来验证中和模型的正确性。以比色温度计和"打靶法"装置来分别测量羽流温度分布和推力,通过试验与仿真结果的对比,羽流温度变化的试验结果与仿真结果在定性规律上一致,推力的计算误差在9%～10%。在验证模型正确性的基础上,利用该数值模型对关键设计参数进行数值分析。结果表明:引出极与发射极的内径比变化会导致外加电场对剩余电荷颗粒作负功,引起推力下降,该物理参数在0.94附近时,推力达到极大值;而随着颗粒直径的增加,羽流中和区域整体向下游推移,推力升高。本文结论可为NFET的反向充电中和策略提供设计参考。     

电磁辅助激光熔化沉积的残余应力

针对激光熔化沉积内部残余应力较大的问题,对其产生的机理作了分析。基于电磁场的应用原理,提出电磁辅助激光熔化沉积以降低其残余应力的方法。利用ANSYS参数化编程语言APDL模拟了电磁辅助激光熔化沉积的过程,分析了成形件残余应力的变化规律,结果表明同步加载轴向电磁力能较好地消减成形件内部残余应力。采用X射线衍射结合电解腐蚀的方法进行深度方向的残余应力测量试验,试验结果验证了电磁辅助的有效性。     

内连导线线宽对沿晶微裂纹演化的影响

基于应力诱发表面扩散的经典理论,用有限元法模拟了线宽对铜内连导线中沿晶微裂纹演化的影响。数值模拟结果表明:随着线宽的减小,椭圆形沿晶微裂纹存在分节与不分节两种演化分叉趋势,且演化分节存在临界线宽珔hc;当珔h≤珔hc时,沿晶微裂纹分节成3个新的沿晶微裂纹;当珔h珔hc时,沿晶微裂纹圆柱化。沿晶微裂纹分节时间^tf随线宽的减小而减小,即减小线宽会加速微裂纹分节。临界外载珋σc与临界形态比βc随线宽的减小而减小,即减小线宽有利于沿晶微裂纹分节。临界外载和临界形态比随晶界能与表面能比值的增大而减小,且沿晶微裂纹比晶内微裂纹更易发生分节。     

六自由度激励台的结构动力学等效建模

六自由度激励台是多轴同步振动环境模拟的重要地面设备,因其结构复杂且具有多个运动自由度,而难以构建准确的结构动力学模型。文章针对6-PSU构型激励台的结构动力学特性,提出其参数型建模与模型修正方法。首先确定模型修正的对象为含轴承和导轨等接触运动副的铰链与作动部件,提出采用刚度与质量解耦的方法建立其含参等效动力学有限元模型;然后以该等效模型为基础,通过模态参数修正铰链和作动部件等效梁模型参数,再利用频响函数修正模型中轴承和导轨的接触刚度参数,得到了修正后的激励台等效结构动力学模型。修正后的有限元模型计算结果与试验结果吻合较好,验证了建模方法的有效性。