一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

空冷电机气动噪声的分析与验证

介绍了空冷电机气动噪声的来源、测量方法以及工程上常用的气动噪声控制措施。以某空冷电机为例,采用CFD方法对外风路的稳态流场、瞬态流场以及声场进行了数值分析,将计算结果通过试验进行验证。这对自通风型空冷电机的气动噪声分析具有一定的参考意义。     

基于单应性矩阵的模型迎角单目视频测量方法

风洞试验中模型迎角的精准测量是降低阻力系数误差的重要途径之一,为此,提出了基于单应性矩阵的模型迎角单目视频测量方法。该方法通过两个单应性矩阵,获取试验过程中相机实时位姿和标记点物方空间位置坐标,应用坐标旋转关系,完成试验模型的迎角测量。数值仿真试验结果表明：迎角测量误差与待测标记点到风洞壁板间的距离偏差近似为线性关系,因此,当标记点不满足共面条件时,可根据该特点进行测量误差修正。静态标定和风洞迎角测量试验结果表明：修正系统误差后,迎角实测数据的测量准度在0.01°以内,精度不超过0.012°。本文方法易于实施,工程实用价值强。     

超高速干气密封扰流效应及抑扰机制

干气密封在高速时优异的动压性能使其应用范围从传统的压缩机、离心机等中高速设备逐渐扩大到航空发动机、（微型）燃气轮机等超高速设备中。基于实际超高速工况特点,对转速范围为10 000~120 000 r/min时的干气密封性能进行了系统性仿真计算,结果发现：在一定几何参数和工况参数下,类似于气浮轴承的微振动现象,干气密封会出现疑似受气体压力波动流影响的开启力、泄漏量与转速非正相关变化的扰流现象,尤其在高压、大膜厚、小槽深时的扰流效应愈加显著;在转速持续增大过程中,干气密封微尺度流场会出现二次拐点现象,且一次拐点发生转速与设计参数有关,而二次拐点发生转速基本约为90 000 r/min。同时结合导流织构的设计思路,进一步研究了超高速下干气密封槽底导流织构的驱动导流效应,结果表明：加设导流织构后,承载效果明显提高,拐点发生工况延后且压力波动区域被压缩。表明导流织构具有良好的抑制扰流、维持开启力与转速持续正相关的作用,在此基础上,进一步阐释了导流织构的抑扰机制,以期为突破干气密封在超高速工况下的应用壁垒提供新思路。     

Deformation behavior of non-rigid airships in wind tunnel tests

Deformation behavior of non-rigid airships in wind tunnel tests is studied by considering three factors, including internal pressure, flow velocity and angle of attack. Fiber Bragg grating strain sensors are used to measure the deformation of non-rigid airships. Wind tunnel tests in the case of different flow velocities and angles of attack are conducted. The measurement results reveal that the airship deformation is in proportion to internal pressure. For the tensile region,the airship deformation is in proportion to flow velocity. Effects of angle of attack on structural deformation are more complicated and there is no clear relationship existing between airship deformation and angle of attack.     

Fault diagnosis based on measurement reconstruction of HPT exit pressure for turbofan engine

Aero-engine gas path health monitoring plays a critical role in Engine Health Management(EHM). To achieve unbiased estimation, traditional filtering methods have strict requirements on measurement parameters which sometimes cannot be measured in engineering. The most typical one is the High-Pressure Turbine(HPT) exit pressure, which is vital to distinguishing failure modes between different turbines. For the case of an abrupt failure occurring in a single turbine component, a model-based sensor measurement reconstruction method is proposed in this paper. First,to estimate the missing measurements, the forward algorithm and the backward algorithm are developed based on corresponding component models according to the failure hypotheses. Then,a new fault diagnosis logic is designed and the traditional nonlinear filter is improved by adding the measurement estimation module and the health parameter correction module, which uses the reconstructed measurement to complete the health parameters estimation. Simulation results show that the proposed method can well restore the desired measurement and the estimated measurement can be used in the turbofan engine gas path diagnosis. Compared with the diagnosis under the condition of missing sensors, this method can distinguish between different failure modes, quantify the variations of health parameters, and achieve good performance at multiple operating points in the flight envelope.     

Availability modeling for periodically inspection system with different lifetime and repair-time distribution

Availability is a main feature of design and operation of all engineering system. Recently,availability evaluation of periodical inspection systems with different structures is at the center of attention due to the wide application in engineering. In this paper, an analytical and probabilistic availability model for periodical inspection system is proposed by a new recursively algorithm,which can achieve limiting average availability and instantaneous availability of periodical inspection system under arbitrary lifetime and repair-time distributions. Then three application examples are presented, the systems lifetime and repair-time are respectively fellow exponential/exponential,Weibull/normal and Weibull/lognormal distribution. Finally, a Weibull/lognormal system is studied to analyze the dynamic relationship between inspection period and availability. The results indicate that the proposed approach can provide the technology support for improving system availability and determining reasonable inspection period.     

Effects of yaw-roll coupling ratio on the lateral-directional departure prediction and restraint

The experimental data obtained from yaw-roll coupled wind tunnel tests are used for lateral-directional departure prediction, by linearizing the_b model to extract nominal dynamic derivatives at each coupling ratio.The prediction results are compared with those of the existing engineering methods which are based on the conventional aerodynamic derivatives.The comparison shows that the yaw-roll coupling ratio has a great influence on the departure susceptibility.The departure resistance will loss in partial region of the coupling ratio when the angle of attack is higher than a critical value.According to the stable and unstable regions of coupling ratio, a two-segment stability augmentation system with two different feedback gain matrices is obtained by pole-placement method.The two-segment stability augmentation system is used in the simulations of straight and level flight, steady turn, spin recovery and Herbst maneuver.The simulation results are also compared with the applications of a fixed-gain stability augmentation system designed by the conventional aerodynamic derivatives.When the yaw-roll coupling effects are fully considered, the two-segment stability augmentation system is more effective for departure restraint and can provide a better flying quality with less control energy.     

基于拉格朗日方法的通气云状空泡三维非定常脱落特性研究

采用均相流模型并结合FBM湍流模型,对绕轴对称回转体通气云状空泡流动特性进行了三维数值模拟,基于实验结果对数值方法进行验证,同时利用基于拉格朗日体系的有限时间李雅普诺夫指数(FTLE)、拉格朗日拟序结构(LCS)和粒子追踪方法分析了其三维非定常脱落特性。研究结果表明:纵截面上空泡覆盖区域的拉格朗日拟序结构整体呈椭球状分布,内部为不规律的复杂拟序结构;不同横截面上拟序结构分布存在很大差异。空泡内部的非对称流动结构和周向流动导致空泡呈现很强的三维运动特性。反向射流在周向上推进的不同步性,是造成空泡呈现不规则断裂和大尺度U型空泡团脱落的主要原因。     

前置不同诱导轮的高速离心泵性能

为研究分流叶片诱导轮及变螺距诱导轮对离心泵水力性能及汽蚀性能的影响,对具有前置诱导轮的高速离心泵进行了试验和数值模拟。外特性试验表明,两种前置诱导轮对高速离心泵效率的影响均不显著,前置分流叶片诱导轮的离心泵扬程相对于前置变螺距诱导轮有显著下降。汽蚀试验表明,小流量工况下前置分流叶片诱导轮的离心泵抗汽蚀性能较优,大流量工况下前置变螺距诱导轮的离心泵抗汽蚀性能较优,其余工况下两者的抗汽蚀性能相当。仿真结果表明,大流量工况下分流叶片诱导轮扬程较低,不能满足离心轮进口能量需求,致使前置分流叶片诱导轮的离心泵汽蚀性能变差。