Design and optimization of a novel electrically controlled high pressure fuel injection system for heavy fuel aircraft piston engine

The heavy fuel compression ignition engines are widely equipped as aircraft piston engines. The fuel injection system is one of the key technologies that determines the performance of engine. One of the main challenges is to precisely control the injected fuel quantity and flow rate in the presence of pressure fluctuation. This challenge is even more serious for heavy fuel. An original design for electrically controlled high pressure fuel injection system called Multi-Pumppressure-reservoirs fuel injection System(MPS) was demonstrated to reduce the pressure fluctuation and help keep injection stable. MPS was compared with an ordinary high pressure Common Rail fuel injection System(CRS). This work established one-dimensional AMESim and mathematical models for both CRS and MPS to study the effect of different structures and geometric parameters on the pressure fluctuations. The calculations show that the average fuel pressure fluctuation of MPS can be reduced by 57% for the crankshaft speed of 1900 r/min, and the pressure fluctuation before injection reduced by 100%. It is concluded that the pressure performance of MPS is less sensitive to pressure reservoir volume than that of CRS, and there is an opportunity for further volume reduction.     

An adaptive fast fixed-time guidance law with an impact angle constraint for intercepting maneuvering targets

Sliding mode guidance laws based on a conventional terminal sliding mode guarantees only finite-time convergence, which verifies that the settling time is required to be estimated by selecting appropriate initial launched conditions. However, rapid convergence to a desired impact angle within a uniform bounded finite time is important in most practical guidance applications. A uniformly finite-time/fixed-time convergent guidance law means that the convergence (settling) time is predefined independently on initial conditions, that is, a closed-loop convergence time can be estimated a priori by guidance parameters. In this paper, a novel adaptive fast fixed-time sliding mode guidance law to intercept maneuver targets at a desired impact angle from any initial heading angle, with no problems of singularity and chattering, is designed. The proposed guidance law achieves system stabilization within bounded settling time independent on initial conditions and achieves more rapid convergence than those of fixed-time stable control methods by accelerating the convergence rate when the system is close to the origin. The achieved acceleration-magnitude constraints are rigorously enforced, and the chattering-free property is guaranteed by adaptive switching gains. Extensive numerical simulations are presented to validate the efficiency and superiority of the proposed guidance law for different initial engagement geometries and impact angles.     

形状记忆合金变刚度结构振动控制仿真研究

为了实现Ti50Ni41Cu9形状记忆合金(SMA)用于复杂结构振动控制的动力学分析,掌握变刚度振动控制的机理和控制规律,基于Kelvin-Voigt粘弹性本构关系,建立了适用于动力学分析的SMA本构模型,并通过ABAQUS编写材料本构程序,形成有效的SMA结构动力学有限元仿真方法,实现了多参数影响下SMA结构的非线性稳态和瞬态动力学仿真计算。计算结果表明:SMA的宏观本构模型能够较好地反映材料动力学性能的变化特征,编制的UMAT子程序与试验数据吻合较好;变刚度控制可以有效降低定频激励引起的稳态响应,对于悬臂板结构响应降幅在40%以上;控制速率与响应的最终变化程度无关,但会引起系统非线性特征,从而影响控制过程需要的时间;采用对向变刚度控制可以降低跨越主频的瞬态振动响应,变温速率越快,系统的峰值响应越小,快速变温时会产生自发频带现象,其对主频能量有显著分散作用,可以一定程度上抑制最大响应峰值。     

三级轴向旋流燃烧室流场结构研究

为深入了解燃烧室内流场,研究不同来流状态对燃烧室流场结构的影响,基于粒子成像速度仪(PIV)技术,对采用三级轴向旋流器的航空发动机燃烧室进行流场测量,分别在Case 1常温低压(0.49MPa)、Case 2常温中压(0.98MPa)、Case 3常温高压(1.64MPa)、Case 4全状态(高温813K高压2.78MPa)来流条件下进行。研究结果表明,同一燃烧室模型在不同速度、温度和压力来流下有基本相同的流场结构,但在中心回流区尺寸、角落回流区尺寸、主燃孔和掺混孔射流等细节方面仍有明显差异,来流压力较高的流场中心回流区向下游扩展更深入,角落回流区被压缩,主燃孔和掺混孔射流速度增加且进气比例增大。     

涡扇发动机低压部件通流耦合计算

为了研究各部件匹配与过渡段几何参数对发动机总体性能的影响,针对某涡扇发动机风扇、低压涡轮、内外涵道、掺混段和尾喷管等部件,基于周向平均Navier-St okes通流控制方程,采用时间推进有限体积法进行了部件耦合计算求解,将沿程各部件性能计算参数与试验做了对比,结果表明:在设计状态下发动机沿程各截面计算特征参数与试验值最大误差不超过5.0%,说明该通流耦合计算方法能够快速预估发动机总体性能,完善各部件匹配关系,在发动机总体设计初期有一定工程应用价值。     

基于非线性规划的室内TOA测距值优化方法

在室内环境中,无线信道中的非视距和多径传输等效应严重影响了到达时间（TOA）定位系统的测距值精度,从而导致较大的测量误差和定位误差。将测距值优化抽象为非线性规划问题,在实现视距/非视距（LOS/NLOS）场景识别的基础上,利用TOA测距误差模型和“目标-基站”间的几何约束为序列二阶非线性规划方法设置合理的初始值,建立了目标函数和约束条件,对定位测距值进行了有效校正。利用典型的TOA测距误差模型进行了仿真验证,利用具有TOA测距功能的无线定位节点在办公环境中进行了实测验证。结果表明,该方法优化后的测距值精度明显优于原始测距值和传统的测距值修正方法,从而验证了该方法的有效性。      

非均质壁面对液滴俘获能力的数值模拟研究

为研究不同非均质壁面对液滴的俘获能力,采用界面追踪法（FTM）结合广义滑移边界建立了接触角模型,对液滴在非均匀润湿的非均质壁面上的运动过程进行了数值模拟研究。液滴在倾斜壁面上受到重力作用由均匀润湿部分下滑至非均匀润湿部分,通过改变Bo数、Oh数、非均匀润湿程度研究了液滴在非均匀润湿区域的运动规律。研究表明:Bo数越大,液滴运动受壁面阻力影响越小,液滴下滑的速度越快,液滴越难以被俘获;Oh数越大,液滴运动受壁面阻力影响越小,液滴越难以被俘获;非均匀润湿程度越大,非均质壁面对液滴的阻力越大,液滴越易被俘获。