燃烧室头部进气规律对煤粉燃烧效率的影响

用实验方法研究了火焰筒式煤粉燃烧室头部进气规律对燃烧效率的影响。通过对6种结构的头部配气方案的分析比较,得出了煤粉燃烧室合理的头部配气方案,为今后煤粉燃烧室的设计和工作状态的选择提供了重要的实验依据。     

太阳射电微波爆发的频谱分析

1981年4月1日太阳发生一个4N级Hα耀斑并伴随出现强烈的IV型射电爆发.本文对北京天文台,西澳大利亚站等射电资料进行分析.分析表明:(1)该事件的微波源状态相对稳定,米波源位置存在移动,因此产生微波辐射与米波辐射是两组不同的电子群体,在爆发频谱指数的时变曲线上表现出明显的形态差异.还由于两者辐射源的位置不同,微波与米波的爆发在峰值时刻上也不完全符合.(2)4月1日微波大爆发是由三个主爆发组成的,它们的峰值时刻分别为0135.1,0146.1,0153.6UT.由射电高频端谱指数算出的非热电子能谱指数表明,在射电爆发的三个峰值时刻电子能谱都变硬.本文还得出该活动区的非热电子平均速度(以光速c为单位)β为0.9左右,磁场强度B为430G.并由回旋同步辐射阻尼算得,非热电子的寿命为829秒,这个数值与三个主峰的持续时间相吻合.     

余辉等离子体的实验研究

利用调制脉冲产生的余辉等离子体的参数测量表明:等离子体空间电位和电子温度的衰变是重要的,它在余辉等离子体的密度衰变过程研究中必须予以考虑.对容器中余辉等离子体密度径向分布的测量结果与理论预言是一致的.     

微波泄漏对光抽运铯束频标准确度影响的分析

微波泄漏是影响光抽运铯原子钟准确度的主要因素之一. 傅里叶变换分析法是分析其影响的主要手段,但该方法只能用来分析有效原子速度分布很窄的情况.通过分析和计算,推导出频移随漏场的位置、相位和幅度变化的关系式.计算和分析的结果表明,漏场引起频移大小和漂移区的长度、输入微波功率值和漏场的相位、强度和位置等有关.所得的结果和用傅里叶变换方法分析所得的结果是一致的,分析的方法不受原子有效速度限制.     

多传感器信息融合技术

多传感器信息融合是Ｃ＾３Ｉ系统和电子综合战系统中的关键技术，本文从信息融合分类出发，讨论了单传感器的信息融合决策理论和技术以及多传感器信息融合原理，提出了多传感器信息融合专家系统，着重讨论贝叶斯法用于二元检测的分布式多传感器信息融合的检测方式。     

钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

湿度传感器能力验证活动误差来源分析

本文主要阐述了本实验室在参加由CNAS组织的湿度传感器能力验证活动中,当最终结果报告中出现临界值情况时,应采取的措施:包括分析误差的主要来源,制定相应的纠正措施,并验证结果的过程。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.