钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

湿度传感器能力验证活动误差来源分析

本文主要阐述了本实验室在参加由CNAS组织的湿度传感器能力验证活动中,当最终结果报告中出现临界值情况时,应采取的措施:包括分析误差的主要来源,制定相应的纠正措施,并验证结果的过程。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

基于STM32的视频流图像更新方法的研究

对基于STM32系统低速(工作主频72MHz)视频流处理显示更新方案的研究。结合图像处理基本理论,分析传统的显示方法的不足,并提出一种新的视频流图像更新的方法,通过一定的实验数据和理论结果,验证该方法可行性。     

Drag Reducing and Increasing Mechanism on Triangular Riblet Surface

Drag reducing and increasing mechanism on riblet surface has been studied through computational fluid dynamics(CFD).Drag reduction is achieved through the optimization of riblet geometry which would affect flow structure inside riblet grooves.Force and flow structure on riblet surface are analyzed and compared with those of smooth surface based on the k-εturbulence model.Drag reducing and increasing mechanism is proved to be related to microvortexes induced inside riblets which lead to Reynolds shear stress reduction significantly and is considered to be the dominant factor resulting in wall friction reduction.Simulation results also show that the pressure drag generating from the deviation of static pressure on the front and rear ends of riblets occurs and grows exponentially with Mach number,which can cause drag increasing.Furthermore,near-wall vortical structures,Reynolds shear stress and static pressure on riblet surfaces are also analyzed in detail.     

LENS风洞试验返回器模型气动热特性模拟

国家数值风洞高超声速流动模拟软件HyFLOW的研制对打破国外同类软件的技术壁垒具有重要意义。与国外DPLR软件进行了对比研究，同时系统介绍了HyFLOW软件求解器的数值方法、物理化学模型以及壁面催化特性计算模型等主要方法，采用典型算例对有限催化模型进行了数值验证，最后基于LENS风洞试验146 mm返回器标模外形开展了高超声速气动热特性数值模拟。研究结果表明，HyFLOW软件在高超声速热化学非平衡流动模拟与评估方面的气动力计算精度高，与国外同类软件DPLR相当，同时其壁面催化条件下的气动热计算精度可靠，可信度高。     

冯子明 航空信息化专家

我国航空企业数字化制造已经有哪些成就,为我国航空企业带来怎样的影响?冯子明:目前国内飞机数字化设计制造水平在不断地提高。数字化的软硬件环境已初具规模,飞机设计已由三维几何模型设计向全信息三维模型设计方向发展     

基于自回归与最小均方理论的振动环境下 光纤陀螺仪滤波方法

针对振动应力下光纤陀螺产生测量误差增大的问题,从振动对光纤环的影响机理出发,分析了振动应力下光纤陀螺干涉信号的表现形式,提出了基于自回归最小均方滤波理论的光纤陀螺滤波方法,将AR模型的平稳性和最小均方根滤波的自适应性相结合,提取平稳数据的特性参数,对高频信号进行滤波,降低非互易相移产生陀螺角速度误差值的干扰.试验表明,该方法简单可行,有效地降低了振动应力下光纤陀螺输出信息的噪声,抑制了由振动引起的陀螺漂移.     

翼吊发动机安装结构等效建模及其隔振设计

为了研究翼吊发动机安装结构隔振特性并优化其隔振器设计,建立了发动机安装节-吊架-机翼结构理论分析及有限元模型.利用有限元方法进行了模态验证并分析了安装结构的隔振特性.进行发动机3种典型工况下的结构动响应分析确定了振动传递的主路径.基于振动传递路径法研究了隔振器参数和安装位置对安装系统隔振性能的影响规律.结果表明:振动载荷经安装结构后低压转子转频和高压转子转频峰值响应分别降低22.03%和14.65%.低压转子转频振动传递主路径为发动机-前安装节-吊架-机翼,高压转子转频为发动机-后安装节-上连杆-机翼.通过合理设置隔振器位置可以使安装系统隔振率达到50.41%,隔振器的频率比为5和阻尼比为0.25时安装系统隔振率可达70.67%.为了优化整个发动机安装系统的隔振效果,设计隔振器时必须选取合适的安装位置和参数.