跨声速压气机多圆柱孔式处理机匣设计与扩稳机理研究

基于对跨声速轴流压气机内部失稳触发机制的认识,设计了一种新型多圆柱孔式处理机匣结构。对带该处理机匣的跨声速轴流压气机转子Rotor-37的内部流动进行了全三维非定常数值模拟,结果表明该新型多圆柱孔式处理机匣结构可使压气机的综合裕度提高6.5%,而最高效率点效率仅降低0.19%。对多圆柱孔式处理机匣的扩稳机理进行了详细分析,结果表明处理机匣能有效消除低速流体团引起的通道阻塞现象,并将低速阻塞流体团抽吸进入处理机匣容腔,然后从前端喷口预旋喷出以抑制叶顶区域的流动分离,从而有效提高跨声速轴流压气机的失速裕度。     

某型飞机后边条焊接盒段优化研究

某型飞机后边条焊接盒段是用于安装平尾的重要受力构件,由材料为30CrMnSiA的板弯件、机加件及加强筋焊接组合而成。由于盒段焊缝数量多、零件壁厚薄,故在组合焊接时容易出现焊接变形、变形后校形困难等问题,使焊缝质量难以保证。本文对焊接盒段结构方案进行了优化研究,在最终选定的结构优化方案中,其盒段壁板为整体机加成型,大量采用机械连接,焊缝数量少,焊接形式简单,缩短了盒段的焊接周期,改善了焊接盒段生产的工艺性,满足了该型号飞机的批产要求。     

A novel resonant converter topology for DC-to-DC power supply

A class-E DC-to-DC converter with half-wave controlled current rectifier is proposed. Its output voltage is controlled by the conduction angle of the rectifier switch at constant switching frequency. Zero voltage switching for all the switches can be maintained from full load to no load. Its steady state characteristics are analyzed and the effects of the circuit parameters are studied. Some extensions of the proposed converter are also discussed. The analysis is verified by PSPICE simulation and an experimental prototype     

配电自动化系统安全防护方案的研究

论文在描述配电自动化系统的功能和结构的基础上 ,根据全国电力二次系统安全防护总体方案 ,提出了配电自动化系统的安全防护方案。     

The Dynamic Stability of a Dual-Spin Satellite

The attitude stability of a dual-spin satellite containing energy disipators on both bodies is investigated. Following Mingori, a symmetrical configuration of the satellite with a mass-spring-dashpot damper on each part is considered, and some new stability results are derived by the application of the Routh-Hurwitz criterion. lt is indicated that the Routh-Hurwitz criterion gives only sufficient conditions of stability for the dual-spin satellite considered. A criterion which is believed to represent both the necessary and sufficient condition of stability is presented here and this is used to check the stability of two specific designs of the dual-spin satellite.     

The GYROLITE: Is it Unstable?

A new derivation of the GYROLITE stability criterion is presented. It is confirmed that, for the satellite to have a stable attitude, the spinning part must have a favorable inertia ratio.     

A Nutation Damper for a Dual-Spin Spacecraft

This paper is concerned with a high-performance nutation damper for use in dual-spin spacecraft. The damper described here makes use of a wheel of uniform mass distribution. The wheel experiences torques which are produced by inertial forces. Damping and restoring (spring) torques are provided by means of a torsional arrangement built around the center of the wheel. The performance characteristics of the above nutation damper are evaluated by considering the small astronomy satellite (SAS-A) spacecraft parameters, and the results for an optimum design of the damper are presented. Finally, the result for the optimum performance is checked with the help of an approximate analysis.     

超声速燃烧实验研究(Ⅱ)

用电弧加热空气,对带有突扩台阶后扩张形,入口M_a=2.1和3.0的超声速燃烧室进行了实验研究,并对两种不同燃烧室长度、煤油和氢气在垂直和平行喷射下的燃烧状况作了比较。     

一种运载火箭用大功率电动伺服驱动器的散热设计

散热对电子设备的性能有着直接的影响,散热器广泛应用于电子产品的热设计用于改善其散热能力,因此散热器应作为关键部件进行设计。针对航天领域使用的大功率电动伺服驱动器的散热问题,提出了通过热力学理论计算指导散热器结构设计的方法。首先通过理论计算结果确定散热器的结构尺寸,然后通过PRO/E三维建模软件对散热器进行建模并利用ANYSY ICEPAK热仿真软件对所设计的散热器进行热仿真,最后搭建了伺服驱动器的热试验环境。仿真结果和试验数据均验证了该设计方法的正确性。     

Vibration signal-based chatter identification for milling of thin-walled structure

In high speed milling aeronautical part, tool condition monitoring(TCM) is very important, because it is prone to get a chatter owing to the low stiffness of thin-walled structures. And the TCM is key technology for automated machining. In this paper, aiming to chatter monitoring in thin-walled structure milling, a variational mode decomposition – energy distribution(VMD-ED)method is proposed to improve the identification accuracy. And a moving average root mean square – mean value(MARMS-MV) ide...