TC1和TC4钛合金腐蚀加工溶解行为研究

测试了TC1和TC4钛合金在氢氟酸-硝酸溶液中腐蚀加工的E-t曲线和极化曲线,分析了腐蚀加工过程的速率变化,观察了腐蚀加工形貌。在氢氟酸-硝酸腐蚀加工液中,极化曲线呈现活化-钝化特征,氢氟酸浓度较高时,硝酸浓度增大到一定值后,极化曲线呈现自钝化倾向。钝化膜的生成速率和厚度由氢氟酸和硝酸体积比决定,氢氟酸和硝酸体积比为1∶2时,腐蚀加工速率最大。腐蚀加工初期钛合金表面氧化膜被破坏,自腐蚀电位迅速变负,加工速率较大,继续加工,硝酸使钛合金表面发生钝化,导致速率降低,钝化膜的生成和破坏同时进行,当钝化膜的生成与基体溶解达到动态平衡时,自腐蚀电位和加工速率趋于稳定。TC1和TC4钛合金中的Ti和Al优先溶解,随着硝酸浓度的增加,钛合金表面微观凹坑变浅。     

Numerical study of compression corner flowfield using Gao-Yong turbulence model

A numerical simulation of shock wave turbulent boundary layer interaction induced by a 24° compression corner based on Gao-Yong compressible turbulence model was presented.The convection terms and the diffusion terms were calculated using the second-order AUSM (advection upstream splitting method) scheme and the second-order central difference scheme,respectively.The Runge-Kutta time marching method was employed to solve the governing equations for steady state solutions.Significant flow separation-region which indicates highly non-isotropic turbulence structure has been found in the present work due to intensity interaction under the 24° compression corner.Comparisons between the calculated results and experimental data have been carried out,including surface pressure distribution,boundary-layer static pressure profiles and mean velocity profiles.The numerical results agree well with the experimental values,which indicate Gao-Yong compressible turbulence model is suitable for the prediction of shock wave turbulent boundary layer interaction in two-dimensional compression corner flows.      

编织玻璃纤维与碳纤维铺层功能梯度板吸能特性研究

为探讨由SW100/5228A玻璃纤维编织（GFRP）层板与CCF-1/5228A碳纤维复合材料（CFRP）层板以不同比例组成的功能梯度板的吸能性能,用重量80g直径23mm的弹丸对六种比例组成的功能梯度板进行了速度约70m/s的弹道试验。对弹击后的试样进行了损伤分析和剩余强度试验,通过C扫描发现,大面积损伤往往发生在...     

环形脉冲爆震发动机引射性能

采用解析方法得出爆震波在爆震管内的参数分布,应用数值方法对爆震波衰退为激波后的传播、排除过程进行了多循环模拟.通过对环形爆震管非稳态引射过程的分析,得出非稳态引射过程可以分成四个阶段,环形爆震管比传统的圆形爆震管的引射作用更强.不同结构参数的引射喷管对环形爆震管的引射增推性能不同,经过分析,得到了较佳的引射喷管的入口尺...     

NiCrAlYSi涂层/DD6单晶高温合金界面再结晶和互扩散行为

采用电子束物理气相沉积(EB-PVD)在单晶高温合金DD6基体上沉积NiCrAlYSi涂层.利用X射线衍射(XRD)、扫描电镜(SEM)、能谱仪(EDS)以及透射电镜(TEM)等研究了高温扩散过程中NiCrAlYSi/DD6的界面再结晶和互扩散行为.研究结果表明合金表面喷砂处理后的涂层试样经1 323 K真空热处理4 ...     

安装角对压气机叶栅气动噪声特性的影响

 基于大涡模拟(LES)和边界元方法对轴流压气机叶栅湍流流场以及流场诱导的噪声进行计算,在不同叶栅安装角下研究来流攻角和来流雷诺数对叶栅气动噪声产生、辐射的影响。研究表明:来流雷诺数不变时,同一安装角下,随着来流攻角从-5°~20°变化,叶栅监测曲线上的声压级先减小后增大,在0°来流攻角下声压级达到最小。安装角为45°时,外场总声压级随来流攻角的分布与30°安装角变化趋势相近。但安装角为60°时,总声压级的变化则明显变缓。在0°来流攻角下,总声压级比安装角为30°和45°时增加了近6 dB,但在其他正来流攻角下,变化并不明显。叶栅的最小声压值出现在弦线方向附近,安装角改变时,最小声压级出现的位置也不同。安装角不变,随着来流雷诺数的增大,叶栅表面的分离减小,损失降低。但叶栅表面的压力脉动随着来流雷诺数的增大而增大,使外场辐射噪声增加。     

多螺旋桨太阳能无人机横航向操稳特性研究

首先分析了大型高空长航时太阳能无人机由于超大展弦比和高效多螺旋桨带来的航向阻尼增量和航向操纵导数,接着分析了由此带来的横航向动态特性变化,并结合多螺旋桨的操纵特性,提出了多桨航向控制方法,最后进行了仿真验证.结果表明,分布式多桨布局对提高该类无人机的横航向稳定性有较大作用,以多桨的转速变化量最小为目标的最优化航向控制分配方法对超长航时飞行很有利.     

Footprint Problem with Angle of Attack Optimization for High Lifting Reentry Vehicle

A formal analysis to footprint problem with effects of angle of attack (AOA) is presented. First a flexible and rapid standardized method for footprint generation is developed. Zero bank angle control strategy and the maximum crossrange method are used to obtain virtual target set; afterward, closed-loop bank angle guidance law is used to find footprint by solving closest approach problem for each element in virtual target set. Then based on quasi-equilibrium glide condition, the typical inequality reentry trajectory constraints are converted to angle of attack lower boundary constraint. Constrained by the lower boundary, an original and practical angle of attack parametric method is proposed. By using parametric angle of attack profile, optimization algorithm for angle of attack is designed and the impact of angle of attack to footprint is discussed. Simulations with different angle of attack profiles are presented to demonstrate the performance of the proposed footprint solution method and validity of optimal algorithm.     

环形爆震室中火焰加速数值模拟及验证

对带不同数量孔板的环形爆震室进行数值模拟,并通过试验对数值计算进行验证,来研究火焰加速现象、爆燃向爆震转变过程和不同当量比下起爆距离.数值计算采用二维轴对称非定常Navier-Stokes方程来模拟流体动力学过程.研究发现用较低的点火能量对火焰混合区的可燃气点火产生低速火焰,低速火焰向环形爆震室射流并改变方向向出口传播,火焰在孔板的阻碍作用以及火焰诱导激波和反射波的加速作用下,由层流变为湍流,湍流火焰与其诱导激波相互加强,最终引爆未燃混气;还对爆震波在孔板区的传播过程进行了分析,对不同当量比下的火焰速度和起爆距离进行了模拟研究.      

射流点火对爆震管中爆燃转爆震影响的实验

采用射流火焰的点火方式进行了爆震管中乙炔和空气混合物从爆燃向爆震转捩的实验研究.爆震管一端开口一端封闭,在封闭端与爆震管垂直安装预燃室,采用火花塞在预燃室中点火,形成射流火焰引燃爆震管中的混合物.基于光电转换原理研制的火焰测速系统测量了爆震管中火焰传播速度.实验表明,与在爆震管壁面火花塞点火相比,射流火焰点火加大了爆震...