Foreign Object Damage to Fan Rotor Blades of Aeroengine Part Ⅱ： Numerical Simulation of Bird Impact

Bird impact is one of the most dangerous threats to flight safety. The consequences of bird impact can be severe and, therefore, the aircraft components have to be certified for a proven level of bird impact resistance before being put into service. The fan rotor blades of aeroengine are the components being easily impacted by birds. It is necessary to ensure that the fan rotor blades should have adequate resistance against the bird impact, to reduce the flying accidents caused by bird impacts. Using the contacting-impacting algorithm, the numerical simulation is carded out to simulate bird impact. A three-blade computational model is set up for the fan rotor blade having shrouds. The transient response curves of the points corresponding to measured points in experiments, displacements and equivalent stresses on the blades are obtained during the simulation. From the comparison of the transient response curves obtained from numerical simulation with that obtained from experiments, it can be found that the variations in measured points and the corresponding points of simulation are basically the same. The deforming process, the maximum displacements and the maximum equivalent stresses on blades are analyzed. The numerical simulation verifies and complements the experiment results.     

Robust fault-tolerant control for wing flutter under actuator failure

Many control laws, such as optimal controller and classical controller, have seen their applications to suppressing the aeroelastic vibrations of the aeroelastic system. However, those control laws may not work effectively if the aeroelastic system involves actuator faults. In the current study for wing flutter of reentry vehicle, the effect of actuator faults on wing flutter system is rarely considered and few of the fault-tolerant control problems are taken into account. In this paper, we use the radial basis function neural network and the finite-time H_∞ adaptive fault-tolerant control technique to deal with the flutter problem of wings, which is affected by actuator faults, actuator saturation, parameter uncertainties and external disturbances. The theory of this article includes the modeling of wing flutter and fault-tolerant controller design. The stability of the finite-time adaptive fault-tolerant controller is theoretically proved. Simulation results indicate that the designed fault-tolerant flutter controller can effectively deal with the faults in the flutter system and can promptly suppress the wing flutter as well.     

旋转机翼悬停气动特性研究

鸭式旋转机翼(CRW)是一种先进的高速直升机方案,旋翼同时也是机翼,是其最关键气动部件之一。采用结构分区拼接网格技术进行空间离散,分区建立参考系,通过求解多重参考系下的N-S方程来计算旋翼流场,首先以传统的Caradonna-Tung实验旋翼的亚、跨声速悬停流场分析为例验证该方法的可靠性,进而采用该方法对旋转机翼悬停流场进行了数值计算,旋翼拉力计算值和地面实验值吻合较好,结果分析表明旋转机翼的悬停流场有着不同于传统旋翼的流场特性。     

基于相似理论的月球车月面牵引性能预测

引入相似理论对月球车的轮土交互系统进行研究,建立了月壤-车轮交互系统的地面力学相似模型,针对原位月壤内聚力较小的特点,提出了一种无需改变车轮尺寸、以模拟月壤为土壤介质的模型试验方法,对月面重力环境下月球车轮的牵引性能进行预测.利用室内土槽试验和颗粒流仿真相结合的方法对该模型试验方法的有效性进行验证,验证结果与模型试验的理论分析结果较为接近,表明该法具有较好的可行性和有效性,可考虑用于预测月球车的月面牵引性能.     

A100钢表面粗糙度与HVOF碳化钨涂层结合强度

采用超音速火焰喷涂方法在AerMet100钢(A100钢)基体上制备了WC10Co4Cr涂层,研究了不同喷砂条件对AerMet100钢表面粗糙度变化及对涂层与基体结合强度的影响.之后将涂层使用化学方法退除,观察涂层制备对AerMet100钢基体表面状态的影响,分析了粗糙度与涂层结合强度之间的关系.结果表明:AerMet100钢基体不同吹砂工艺产生的表面粗糙度 S_a=0.994~4.983 μm时,超音速火焰喷涂WC10Co4Cr涂层的结合强度均不低于72 MPa.喷涂涂层过程对基体表面状态没有较大影响:基体粗糙度 S_a<2 μm时,喷涂后,基体表面的粗糙度略有降低;基体粗糙度 S_a>3 μm时,喷涂后,基体粗糙度略有升高.超音速火焰喷涂的碳化钨钴涂层与AerMet100钢基体的结合同时存在物理与机械力结合,以前者为主要结合力.     

胶粘剂性能对挖补修理层合板拉伸性能的影响

利用非线性三维有限元模型,对挖补修理复合材料层合板的拉伸破坏行为进行研究,计算结果与试验结果吻合良好,证明了所建模型的有效性.在此基础上,分析了挖补修理层合板的拉伸破坏机理,以及胶粘剂力学性能对挖补结构拉伸性能的影响.最终,总结出挖补修理复合材料结构胶粘剂选用原则以及理想胶粘剂的性能特征.研究结果可为复合材料结构可修理性设计,以及挖补类复合材料层合板端面对接用胶粘剂的研制提供参考.     

基于四路信号处理的载波锁相环

载波跟踪环是独立导航接收机中最为脆弱的部分,在一定载噪比下,影响载波跟踪环跟踪门限的主要因素是动态应力。科斯塔斯锁相环是最常用的载波跟踪环之一,由于频率牵引范围的限制,其对动态应力非常敏感,该频率牵引范围由最大相位牵引范围决定。传统科斯塔斯锁相环是基于两路信号处理进行载波相位锁定的,其相位牵入范围仅为［-π/2,π/2］。文章提出了一种基于四路信号处理的科斯塔斯锁相环,增加的两路信号分别与原来两路相位相差π/4,其相位牵入范围可以达到［-3π/4,3π/4］,较传统方式提高了1/2。仿真结果显示文中提出的设计方法能够明显提高环路的动态性能     

卫星编队对空间非合作目标测距相对导航精度分析

针对单颗卫星对空间非合作目标测距不能估计全部相对运动状态的问题,提出利用编队中多颗卫星同时测距相对导航。建立了相对运动状态估计的系统模型;推导了系统可观测矩阵;通过计算系统可观测度和采用无迹卡尔曼滤波（UKF）对目标相对运动状态进行估计,研究了观测矢量方向和数量与相对导航精度的关系。结果表明双星测距能估计全部相对运动状态,观测矢量夹角越大,相对导航精度越高,在编队尺寸远小于目标距离的前提下,多于两颗的卫星测距并不能明显提高相对导航精度。     

具有广泛适用性的AOS虚拟信道调度算法

针对现有的基于虚拟信道紧迫度的动态调度算法的不足,提出了一种新的高级在轨系统虚拟信道动态调度算法。该算法首先估算虚拟信道的紧迫度和数据帧的紧迫度,然后用加权系数将二者结合起来构造成一个全新的虚拟信道传送紧迫度函数,再根据该函数的值进行判决调度。对于高级在轨系统中不同速率、不同性质、不同类型的星上数据源,该算法均可通过选择合适的加权系数灵活地分配传输时隙,保证各用户合理、动态地占用物理信道,满足对数据的传输时延要求,因此具有广泛的适用性。理论分析和仿真结果表明,本文提出的算法比基于虚拟信道紧迫度的动态调度算法具有更好的性能     

基于超声波的移动机器人多目标探测定位方法

为了使移动机器人能够对离散的多个目标进行准确的探测定位,提出了一种新的超声波智能探测方法.采用3个收发一体的超声换能器阵列发送近似的平面声波波束,并建立空间坐标系.3个探头定时发送超声波脉冲,同时数字信号处理器采集并分析接收到的回波信号,在给定的算法下滤除杂波、识别提取回波首波、二次回波和三次回波等特征信号数据,在正确检测出各路波束的回波时间后,通过计算给出多个被测物体的准确定位.实验采用了杆件物体作为被测对象,对回波信号进行高速数据采集处理后计算出被测目标的坐标值,比较了计算物位与实测物位数据,结果验证了该方法的可行性与正确性.