超高温升中心分级燃烧室设计及计算分析

针对航空发动机高推重比、高温升的需求,提出1种中心分级旋流燃烧室的设计方案。在保证与现有单环腔燃烧室(SAC)进出口尺寸、机匣尺寸限制不变的情况下,对设计模型进行了3维数值模拟,并与现有的单环腔燃烧室数值模拟结果及试验结果进行了对比分析。研究结果表明:设计油气比为0.045时,设计中心分级燃烧室温升可达1356 K,出口温度分布可达0.137,出口径向温度分布可达0.096;此外,与SAC相比,中心分级燃烧室可获得更低的总压损失,更低的出口温度分布系数以及高工况下可获得更高的燃烧效率;污染排放性能表明,中心分级燃烧室在慢车点CO排放比SAC的稍高,在设计点NOx排放按g/kg燃油计比SAC的低。     

基于ZEMAX软件的圆喷管成像畸变校正方法

准确显示圆喷管内流场,对于了解和控制该流场具有一定意义,并能为相关数值计算结果提供验证.为此,必须首先解决较厚圆喷管成像畸变带来有效视场减小的问题,采用圆喷管外加校正柱透镜方法可以予以校正.校正柱透镜的设计采用厚透镜焦距计算和ZEMAX软件优化设计相结合,并进行了静态验证,将有效视场从不到30%提高到了大于80%;其次,校正设计时假设圆喷管内折射率为1,并以平行光出射,通过对这个假设的分析,表明其对圆喷管内一定的高温高压流场显示结果影响较小;然后,分析了流场显示的可行方法,给出了动态显示结果;最后指出了该校正方法的可行性和对于定量干涉测量的局限性.该研究对于圆喷管内燃烧流场的研究具有参考意义.      

柔性扑翼气动结构耦合特性数值研究

微型扑翼体积小、重量轻,其柔性变形对气动特性有显著的影响。通过求解雷诺平均N-S方程(ReynoldsAveraged Navier-Stokes,RANS)和结构动力学方程,对微型柔性扑翼飞行器的气动结构耦合特性进行了数值模拟研究。针对微型扑翼的大幅运动,发展了适用于扑翼的气动结构耦合数值计算方法,研究了微型扑翼的气动结构耦合特性。通过求解雷诺平均Navier-Stokes(RANS)方程得到微型扑翼的非定常气动特性;利用哈密顿原理(Hamilton Principle)推导了扑翼的结构动力学方程,采用结构有限元方法对该动力学方程进行离散并求解,得到扑翼的动态结构特性;采用松耦合方法进行迭代。计算结果与风洞实验结果相比吻合良好,验证了所发展方法的有效性。在此基础上研究了惯性力和关键运动参数对柔性扑翼气动及结构特性的影响规律,有助于比较详细、全面地了解微型扑翼的气动机理,为柔性扑翼的设计提供了参考依据。     

基于北斗的车载接收机航向测量技术研究

研究一种BD2双天线的双频基线测量算法,实现了在车载动态条件下利用BD2卫星进行载体航向实时测量,满足军用车辆、无人机、船舶舰艇等载体高精度、快速实时、连续稳定长时间工作、低成本的要求,对算法实现进行了试验验证,取得了理想的成效,具有较强的工程实用价值。     

Design and experimental study of a micro-groove grinding wheel with spray cooling effect

The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl- shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200℃, which means the developed grinding wheel makes cooling high efficient and low energy consuming.     

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

2013 年国外载人航天发展综合分析

2013年,各主要航天国家依据本国具体国情,以审慎务实的态度持续推进载人航天活动。基于此背景,综述了2013年国外载人航天领域发展动态,梳理了国际空间站及深空探索领域的系列成果,分析了重型运载火箭、新型飞船、空间商业运输能力的发展趋势。     

Coupling damage and reliability model of low-cycle fatigue and high energy impact based on the local stress–strain approach

Fatigue induced products generally bear fatigue loads accompanied by impact processes,which reduces their reliable life rapidly. This paper introduces a reliability assessment model based on a local stress–strain approach considering both low-cycle fatigue and high energy impact loads.Two coupling relationships between fatigue and impact are given with effects of an impact process on fatigue damage and effects of fatigue damage on impact performance. The analysis of the former modifies the fatigue parameters and the Manson–Coffin equation for fatigue life based on material theories. On the other hand, the latter proposes the coupling variables and the difference of fracture toughness caused by accumulative fatigue damage. To form an overall reliability model including both fatigue failure and impact failure, a competing risk model is developed. A case study of an actuator cylinder is given to validate this method.     

Friction moment analysis of space gyroscope bearing with ribbon cage under ultra-low oscillatory motion

This paper presents the model of calculating the total friction moment of space gyroscope ball bearings which usually work under ultra-low oscillatory motion and are very sensitive to the friction moment. The aim is to know the proportion of the friction moment caused by each frictional source in the bearing＇s total friction moment, which is helpful to optimize the bearing design to deduce the friction moment. In the model, the cage dynamic equations considering six degree-of-freedom and the balls dynamic equations considering two degree-of-freedom were solved.The good trends with different loads between the measured friction moments and computational results prove that the model under constant rate was validated. The computational results show that when the speed was set at 5 r/min, the bearing＇s maximum total friction moment when oscillation occurred was obviously larger than that occurred at a constant rate. At the onset of each oscillatory motion, the proportion of the friction moment caused by cage in the bearing＇s total friction moment was very high, and it increased with the increasing speed. The analyses of different cage thicknesses and different clearances between cage pocket and ball show that smaller thickness and clearance were preferred.