磁悬浮框架飞轮磁轴承技术研究与发展现状

对磁悬浮框架飞轮(MSGFW)和高精度磁轴承研究现状及其未来发展进行了详细阐述。根据转子悬浮力类型，将磁悬浮框架飞轮分为磁阻力构型、洛伦兹力构型和混合力构型，并结合三种构型论述了国内外框架飞轮的发展过程。在此基础上，对球面磁阻力磁轴承和洛伦兹力磁轴承进行了详细介绍，并结合磁路图分析其工作原理，比较了同类磁轴承的优劣。展望了磁悬浮框架飞轮与高精度磁轴承的未来发展方向，指出高动态响应检控共位平动球面磁阻力磁轴承，标准磁悬浮动量球和磁悬浮控制敏感球是磁悬浮框架飞轮的研究重点。     

基于最小曲率半径的软波导安全裕度校核方法

针对传统软波导安全裕度校核方法存在不够准确和/或计算量难以承受的缺陷,文章提出一种基于最小曲率半径的软波导安全裕度校核方法,分析其可行性、便利性及准确性,并给出具体的计算步骤.对同一个算例的分析结果表明,与传统方法相比,此方法可以更加准确地反映软波导的安全裕度.     

反推发动机失效模式对返回舱着陆姿态的影响分析

以稳定下降阶段的降落伞-返回舱系统的动力学模型为基础,针对反推发动机不同的失效模式,建立了4种返回舱反推力模型,通过计算获知了4种返回舱着陆角和速度的变化情况,计算结果可为反推发动机失效情况下被动缓冲装置的设计输入提供参考,同时也可为返回舱着陆安全性评估和制定故障预案提供一定的参考。     

A closed-form solution for moving source localization using LBI changing rate of phase difference only

Due to the deficiencies in the conventional multiple-receiver localization systems based on direction of arrival(DOA) such as system complexity of interferometer or array and amplitude/phase unbalance between multiple receiving channels and constraint on antenna configuration,a new radiated source localization method using the changing rate of phase difference(CRPD)measured by a long baseline interferometer(LBI) only is studied. To solve the strictly nonlinear problem, a two-stage closed-form solution is proposed. In the first stage, the DOA and its changing rate are estimated from the CRPD of each observer by the pseudolinear least square(PLS) method,and then in the second stage, the source position and velocity are found by another PLS minimization. The bias of the algorithm caused by the correlation between the measurement matrix and the noise in the second stage is analyzed. To reduce this bias, an instrumental variable(IV) method is derived. A weighted IV estimator is given in order to reduce the estimation variance. The proposed method does not need any initial guess and the computation is small. The Cramer–Rao lower bound(CRLB) and mean square error(MSE) are also analyzed. Simulation results show that the proposed method can be close to the CRLB with moderate Gaussian measurement noise.     

Optimization of beamforming and path planning for UAV-assisted wireless relay networks

Recently, unmanned aerial vehicles （UAVs） acting as relay platforms have attracted considerable attention due to the advantages of extending coverage and improving connectivity for long-range communications. Specifically, in the scenario where the access point （AP） is mobile, a UAV needs to find an efficient path to guarantee the connectivity of the relay link. Motivated by this fact, this paper proposes an optimal design for beamforming （BF） and UAV path planning. First of all, we study a dual-hop amplify-and-forward （AF） wireless relay network, in which a UAV is used as relay between a mobile AP and a fixed base station （BS）. In the network, both of the AP and the BS are equipped with multiple antennas, whereas the UAV has a single antenna. Then, we obtain the output signal~to-noise ratio （SNR） of the dual-hop relay network. Based on the criterion of maximizing the output SNR, we develop an optimal design to obtain the solution of the optimal BF weight vector and the UAV heading angle. Next, we derive the closed-form outage probability （OP） expression to investigate the performance of the dual-hop relay network conveniently. Finally, computer simulations show that the proposed approach can obtain nearly optimal flying path and OP performance, indicating the effectiveness of the proposed algorithm. Furthermore, we find that increasing the antenna number at the BS or the maximal heading angle can significantly improve the performance of the considered relay network.     

基于自适应粒子滤波的涡扇发动机故障诊断

针对涡扇发动机非线性、非高斯的特点,提出了一种自适应的粒子滤波算法用于涡扇发动机气路部件突变故障的诊断.为了减小算法的计算量并且保证滤波精度,分析了滤波精度和样本数目的关系,提出根据滤波过程中状态的方差自适应地调整粒子数,在保证一定的滤波精度下可以有效地减少滤波过程中使用的粒子数,提高了算法的实时性.同时,引入扩展卡尔曼滤波(EKF)用于更新粒子,产生重要概率密度函数,在一定程度上避免了粒子的退化.通过某型涡扇发动机的仿真分析表明:改进的算法相比标准粒子滤波算法用于涡扇发动机气路部件故障诊断时,参数估计的方均根误差减小了50%左右,且算法的计算量减小了30%.     

次流通道对双喉道气动矢量喷管的性能影响研究

为了进一步了解次流通道对双喉道气动矢量喷管(Dual Throat Nozzle,DTN)气动矢量性能的影响,基于二维DTN喷管构型进行了详细的数值模拟研究。结果表明:收扩的次流通道相对于平直的次流通道不会改善DTN喷管的推力矢量性能;随着次流流量增加,DTN的推力矢量角存在一个最大值,超过该值各推力矢量性能均会降低;次流通道宽度对DTN喷管推力矢量性能影响显著:(1)次流宽度不影响所能达到的最大推力矢量角;(2)小的次流宽度在进口总压较高的条件下具有更高的推力矢量角;(3)增大次流宽度能降低次流总压,但达到的矢量角会有所减小。     

新型免抬式电动刀架的研究

本文介绍了一种ＣＮＣ机床新型免抬式电动刀架的机械结构及控制电路。该电动刀架采用梯形螺柱螺套副升降机构，可使刀架转位分度时无需抬起上刀体。刀架转位分度采用机－ 电结合的方法，即先在控制电路中使用霍尔元件进行粗定位，再在机械上采用三齿盘实现精定位。     

描述人造地球卫星轨道的四元数法

简要介绍了描述人造地球卫星轨道的方法,分析了已有方法在求解空间拦截与交会问题时遇到的困难.通过用四元数描述轨道坐标系空间方位的途径,把四元数引入描述卫星轨道运动的参数体系,用矢量导数转换的方法求出了卫星绝对加速度在轨道坐标系内的表达式,得出了包含四元数在内的卫星质心的空间运动方程.