同步串行总线在通信卫星转发器中的应用

提出了一种适用于通信卫星转发器分系统测控数据传输的5线制同步串行总线,支持30个终端同时接入,改变了通信卫星平台传统的点对点式的遥测遥控信息传输方式,大大减少了通信舱内电缆数量;并在某通信卫星载荷舱上进行了应用,使卫星载荷舱质量减少几十千克,提升了卫星平台的有效载荷能力。文章设计的串行总线提供标准的接口电路,有利于有效载荷设备的扩容,可以推广至更多的有效载荷设备,构成其之间的测控信息网络。     

Design and analysis of an extended mission of CE-2: From lunar orbit to Sun–Earth L2 region

Chang’E-2 (CE-2) has firstly successfully achieved the exploring mission from lunar orbit to Sun–Earth L2 region. In this paper, we discuss the design problem of transfer trajectory and at the same time analyze the visible segment of Tracking, Telemetry & Control (TT&C) system for this mission. Firstly, the four-body problem of Sun–Earth–Moon and Spacecraft can be decoupled in two different three-body problems (Sun–Earth + Moon Restricted Three-Body Problems (RTBPs) and Earth–Moon ephemeris model). Then, the transfer trajectory segments in different model are computed, respectively, and patched by Poincaré sections. The full-flight trajectory including transfer trajectory from lunar orbit to Sun–Earth L2 region and target Lissajous orbit is obtained by the differential correction method. Finally, the visibility of TT&C system at the key time is analyzed. Actual execution of CE-2 extended mission shows that the trajectory design of CE-2 mission is feasible.     

C/SiC复合材料铣削表面完整性研究

采用PCD刀具进行了C/SiC复合材料的铣削加工实验,通过观察加工表面/亚表面损伤,分析了C/SiC复合材料铣削加工表面形成机制,并结合切削力讨论了铣削参数对加工表面形貌和粗糙度的影响。研究结果表明,C/SiC材料以脆性断裂方式实现去除;加工表面存在纤维的层状脆断、拔出和纤维束断裂等现象;碳纤维区域粗糙度随铣削参数的变化规律与表面微观形貌基本一致;提高切削速度能改善表面质量,增大切深会使表面质量严重恶化,每齿进给量对表面质量影响较小。     

增强立尾效益的主动流动控制

本文叙述和讨论了某些增强立尾效益的主动流动控制（AFC）技术的研究。在NASA ERA项目支持下Rensselaer学院完成了4%和5%缩比立尾模型的合成射流AFC风洞试验,加州理工学院完成了14%缩比立尾模型的振荡射流AFC风洞试验,后者表明当动量系数为1.7%时可获50%的侧向力增量。基于将上述两种AFC技术集成于飞机系统的可行性研究,Boeing在Ames NFAC（40 ft×80 ft风洞）完成了B-757全尺寸立尾风洞模型试验,在风速为100 knots,方向舵偏角为30°和侧滑角为0°与-7.5°下,得出采用31个振荡射流激振器可获得20%侧向力增量。NASA ERA项目组与Boeing共同努力在2015年春实现了装有31个振荡射流激振器的B-757 ecoDemonstrator飞行试验。飞行员反馈和13%~16%侧向力增量的飞行试验初步分析结果表明了振荡射流AFC技术的成功。     

Interface flux reconstruction method based on optimized weight essentially non-oscillatory scheme

Aimed at the computational aeroacoustics multi-scale problem of complex configurations discretized with multi-size mesh, the flux reconstruction method based on modified Weight Essentially Non-Oscillatory (WENO) scheme is proposed at the interfaces of multi-block grids. With the idea of Dispersion-Relation-Preserving (DRP) scheme, different weight coefficients are obtained by optimization, so that it is in WENO schemes with various characteristics of dispersion and dissipation. On the basis, hybrid flux vector splitting method is utilized to intelligently judge the amplitude of the gap between grid interfaces. After the simulation and analysis of 1D convection equation with different initial conditions, modified WENO scheme is proved to be able to independently distinguish the gap amplitude and generate corresponding dissipation according to the grid resolution. Using the idea of flux reconstruction at grid interfaces, modified WENO scheme with increasing dissipation is applied at grid points, while DRP scheme with low dispersion and dissipation is applied at the inner part of grids. Moreover, Gauss impulse spread and periodic point sound source flow among three cylinders with multi-scale grids are carried out. The results show that the flux reconstruction method at grid interfaces is capable of dealing with Computational AeroAcoustics (CAA) multi-scale problems.     

基于侧扫声纳图像的AUV侧向速度估计与DVL粗差检测

复杂水底环境和自主潜航器(AUV）机动会造成Doppler测速仪(DVL）速度测量结果中出现粗差,提出一种检测DVL速度粗差数据的方法。该方法利用侧扫声纳图像数据,结合SIFT特征匹配算法求取声纳图像的边缘特征点。根据声纳图像成像原理,计算出每一帧图像相对上一帧图像对应特征点像素的横向平移量;结合特征像素平移量与AUV实际横向位移的比例尺度关系以及声纳侧扫周期推算出AUV侧向速度。该侧向速度用于检测水下组合导航中DVL的速度粗差,在几十米水深的浅水区,该方法能够检测并剔除出大于0.2m/s的DVL侧向速度粗差,显著减小DVL前向速度误差。算法可实时实现,改善AUV水下组合导航性能。     

钛合金TB6刀具磨损铣削实验研究

使用硬质合金刀具对钛合金TB6进行正交铣削实验,对比分析不同切削参数下的刀具磨损情况,并用实验结果进行回归分析得到刀具磨损的回归公式。结果表明:刀具主要磨损在后刀面,其磨损大都呈现一条带状磨损带,在速度增大时大磨损带变长,刀具易发生脆性破损,且在刀具表面会出现钛合金粘连;对刀具耐用度的影响大小依次为切削速度、进给量、切削宽度和切削深度;刀具磨损回归方程具有良好的回归方差,能够很好的对刀具寿命进行预测。     

一种多钉铆接连接件的疲劳寿命分析方法

针对目前对多钉铆接连接件进行疲劳寿命分析时的可行性不高、计算量较大等问题,提出一种更加有效可靠的预测多钉铆接连接件的疲劳寿命的方法。对多钉铆接连接件进行疲劳寿命分析时,先对压铆铆接过程进行了显示动力学分析,获得铆接后的钉、孔变形形式和干涉量,并编写了APDL子程序用于各种形式试件的铆接过程分析。用紧固件的载荷-位移曲线进行细节应力分析。基于三维弹塑性有限元法建立铆接连接件的载荷-位移计算方法,并通过与试验结果对比,说明用本文方法获取载荷-位移曲线的可靠性。在ANSYS中建立钉单元,并实现参数化建模进行钉载计算。使用应力严重系数法估算连接件疲劳寿命。开展典型航空铆接连接件疲劳试验,计算结果与试验结果一致性较好,说明计算方法的可行性。