Selection of the Mars Science Laboratory Landing Site

The selection of Gale crater as the Mars Science Laboratory landing site took over five years, involved broad participation of the science community via five open workshops, and narrowed an initial >50 sites (25 by 20?km) to four finalists (Eberswalde, Gale, Holden and Mawrth) based on science and safety. Engineering constraints important to the selection included: (1)?latitude (±30°) for thermal management of the rover and instruments, (2)?elevation (<?1?km) for sufficient atmosphere to slow the spacecraft, (3)?relief of <100–130?m at baselines of 1–1000?m for control authority and sufficient fuel during powered descent, (4)?slopes of <30° at baselines of 2–5?m for rover stability at touchdown, (5)?moderate rock abundance to avoid impacting the belly pan during touchdown, and (6)?a?radar-reflective, load-bearing, and trafficable surface that is safe for landing and roving and not dominated by fine-grained dust. Science criteria important for the selection include the ability to assess past habitable environments, which include diversity, context, and biosignature (including organics) preservation. Sites were evaluated in detail using targeted data from instruments on all active orbiters, and especially Mars Reconnaissance Orbiter. All of the final four sites have layered sedimentary rocks with spectral evidence for phyllosilicates that clearly address the science objectives of the mission. Sophisticated entry, descent and landing simulations that include detailed information on all of the engineering constraints indicate all of the final four sites are safe for landing. Evaluation of the traversabilty of the landing sites and target “go to” areas outside of the ellipse using slope and material properties information indicates that all are trafficable and “go to” sites can be accessed within the lifetime of the mission. In the final selection, Gale crater was favored over Eberswalde based on its greater diversity and potential habitability.     

Proportional fuzzy feed-forward architecture control validation by wind tunnel tests of a morphing wing

In aircraft wing design, engineers aim to provide the best possible aerodynamic performance under cruise flight conditions in terms of lift-to-drag ratio. Conventional control sur-faces such as flaps, ailerons, variable wing sweep and spoilers are used to trim the aircraft for other flight conditions. The appearance of the morphing wing concept launched a new challenge in the area of overall wing and aircraft performance improvement during different flight segments by locally altering the flow over the aircraft's wings. This paper describes the development and appli-cation of a control system for an actuation mechanism integrated in a new morphing wing structure. The controlled actuation system includes four similar miniature electromechanical actuators dis-posed in two parallel actuation lines. The experimental model of the morphing wing is based on a full-scale portion of an aircraft wing, which is equipped with an aileron. The upper surface of the wing is a flexible one, being closed to the wing tip; the flexible skin is made of light composite materials. The four actuators are controlled in unison to change the flexible upper surface to improve the flow quality on the upper surface by delaying or advancing the transition point from laminar to turbulent regime. The actuators transform the torque into vertical forces. Their bases are fixed on the wing ribs and their top link arms are attached to supporting plates fixed onto the flex-ible skin with screws. The actuators push or pull the flexible skin using the necessary torque until the desired vertical displacement of each actuator is achieved. The four vertical displacements of the actuators, correlated with the new shape of the wing, are provided by a database obtained through a preliminary aerodynamic optimization for specific flight conditions. The control system is designed to control the positions of the actuators in real time in order to obtain and to maintain the desired shape of the wing for a specified flight condition. The feasibility and effectiveness of the developed control system by use of a proportional fuzzy feed-forward methodology are demon-strated experimentally through bench and wind tunnel tests of the morphing wing model.     

A high-order SPH method by introducing inverse kernels

The smoothed particle hydrodynamics (SPH) method is usually expected to be an effi-cient numerical tool for calculating the fluid-structure interactions in compressors; however, an endogenetic restriction is the problem of low-order consistency. A high-order SPH method by intro-ducing inverse kernels, which is quite easy to be implemented but efficient, is proposed for solving this restriction. The basic inverse method and the special treatment near boundary are introduced with also the discussion of the combination of the Least-Square (LS) and Moving-Least-Square (MLS) methods. Then detailed analysis in spectral space is presented for people to better under-stand this method. Finally we show three test examples to verify the method behavior.     

Fine structure of the interplanetary shock front according to measurements of the ion flux of the solar wind with high time resolution

According to the data of the BMSW/SPEKTR-R instrument, which measured the density and velocity of solar wind plasma with a record time resolution, up to ~3 ×10^–2 s, the structure of the front of interplanetary shocks has been investigated. The results of these first investigations were compared with the results of studying the structure of the bow shocks obtained in previous years. A comparison has shown that the quasi-stationary (averaged over the rapid oscillations) distribution of plasma behind the interplanetary shock front was significantly more inhomogeneous than that behind the bow-shock front, i.e., in the magnetosheath. It has also been shown that, to determine the size of internal structures of the fronts of quasi-perpendicular (θ_BN > 45°) shocks, one could use the magnetic field magnitude, the proton density, and the proton flux of the solar wind on almost equal terms. A comparison of low Mach (М _А < 2), low beta (β₁ < 1) fronts of interplanetary and bow shocks has shown that the dispersion of oblique magnetosonic waves plays an essential role in their formation.     

准一维传热下冷面绝热边界材料对隔热试验结果的影响

为评估冷面绝热边界对试验结果的影响,在充分验证测控系统可控性和试验方法稳定性的基础上,分别以柔性隔热毡、刚性隔热瓦和纳米隔热材料为冷面绝热边界,对陶瓷纤维刚性隔热材料进行500℃、3 000s的石英灯热辐射考核试验,并利用迭代绝热边界当量热导率的方法对试验结果进行了模拟计算和分析。结果表明,以柔性隔热毡为冷面绝热边界时隔热材料的冷面温度最高,刚性隔热瓦和纳米隔热材料为冷面绝热边界时则冷面温度较低且相近,3者间最大相对偏差高达19.0%。模拟计算证实由冷面绝热边界材料引起的接触热阻对试验结果起到了决定性作用,而不简单地取决于绝热边界材料的隔热性能。     

The Dawn Framing Camera

The Framing Camera (FC) is the German contribution to the Dawn mission. The camera will map 4 Vesta and 1 Ceres through a clear filter and 7 band-pass filters covering the wavelengths from the visible to the near-IR. The camera will allow the determination of the physical parameters of the asteroids, the reconstruction of their global shape as well as local topography and surface geomorphology, and provide information on composition via surface reflectance characteristics. The camera will also serve for orbit navigation. The resolution of the Framing Camera will be up to 12 m per pixel in low altitude mapping orbit at Vesta (62 m per pixel at Ceres), at an angular resolution of 93.7 ??rad?px^?1. The instrument uses a reclosable front door to protect the optical system and a filter-wheel mechanism to select the band-pass for observation. The detector data is read out and processed by a data processing unit. A power converter unit supplies all required power rails for operation and thermal maintenance. For redundancy reasons, two identical cameras were provided, both located side by side on the +Z-deck of the spacecraft. Each camera has a mass of 5.5 kg.     

多载波DS—CDMA在数字微波通信系统中的应用

基于数字微波通信系统的特点，介绍了多载波SD-CDMA（Multicarrier-DS-CDMA,即MC-DS-CDMA）调制技术的基本原理及其应用于数字微波通信系统中的具体实现方法。从理论上详细地分析了MC-CDMA工作方式的性能，并将其与传统的数字微波通信系统进行了比较，阐明了将MC-DS-CDMA工作方式应用于数字微波通信系统的必要性。     

带着全家去出海

这个夏天,有没有筹划一次全家人都可以参与的旅行呢?带着爱人或者家里的小朋友与大自然进行一次深入的交流,想必对于彼此之前感情的沟通能起到不错的作用。如果可以,带着全家去出海吧!