RBCC发动机性能分析方法研究

通过进行前体的边界层效应修正、采用有限化学反应速率模型和中心差分形式的Mac Cormack格式,求解燃烧室性能分析模型方程,以及采用灵活的发动机性能计算方法等,建立了较为完善的RBCC发动机性能分析模型及软件,并进行了软件应用研究。分别采用二维CFD计算和试验结果对该模型进行了校验,其相对误差小于10%。结果表明,该软件适用于RBCC发动机性能分析。     

热暴露对B/Al复合材料性能的影响

对经300℃、500℃高温热暴露的B／Al（LF6）复合材料的力学性能进行了研究，实验结果表明材料在300℃下热暴露时，性能下降速度较慢，100h后强度保留率约为76％，延伸率保留率为74％。而在500℃下热暴露时，5h以上强度就有明显降低。高温长时间热暴露后复合材料的断裂也从积累型转变为典型的非累积型断裂。通过透射电镜（TEM）及扫描电镜（SEM）对固态热压制造态和主温热暴露的界面状况进行了分析，认为界面反应是造成B／Al复合材料力学性能下降的主要原因。     

飞机支柱式起落架落震仿真及缓冲器优化分析

主要介绍支柱式起落架缓冲器的各个参数,包括缓冲支柱的初压力、初容积、油孔面积、活塞面积、缓冲支柱行程等。介绍起落架落震时缓冲器轴向载荷的计算公式。结合具体飞机型号利用初始参数通过AD-AMS软件建立数值模型并进行仿真分析,计算结果与试验结果比较,发现两者具有较好的一致性。最后以起落架缓冲器的油孔面积作为设计参数进行优化分析,给出最优值。     

SCR技术制备A2017半固态材料及其触变性能的研究

单辊搅拌技术 (SCRShearing/CoolingRollProcess)技术制备的A2 0 17半固态材料比常规铸造坯组织优良 ;SCR技术制备的A2 0 17半固态材料在 5 30～ 5 70℃范围内 ,可以进行触变成形 ;半固态成形平均屈服强度比热加工时的屈服强度低 10MPa ;A2 0 17半固态材料触变过程分为四个阶段 ,稳定触变阶段A2 0 17半固态材料的触变性能稳定 ,半固态加工时容许的最大加工变形范围为 6 4 %～ 72 %。     

农林飞机结构抗坠毁设计技术

农林飞机通常在3-5m的超低空进行作业飞行,在离地面3m以上的空中往往会有树木、电线杆、电线、堤坝、土堆、山丘、建筑物等障碍物,稍有不慎,就有与之撞击的可能。这样的工作条件除要求飞机具有良好的超低空飞行性能以外,还要求飞机具有一定的耐坠撞能力。本文针对农林飞机执行任务过程中可能发生的碰撞、坠毁等特点,研究了农林飞机抗坠毁设计技术、计算分析仿真技术。     

飞机主操纵系统疲劳试验载荷监控方法研究——应变数据分析法

针对某机全机主操纵系统疲劳试验中动态操纵情况下的应变测量以及试验载荷监控问题进行了分析和讨论,并对基于应变测量数据分析的操纵系统疲劳试验载荷监控方法的确定及其应用效果进行了阐述。在操纵系统疲劳试验过程中的实际监控结果表明,该方法对副翼/平尾/方向舵操纵系统多种试验状态下的试验载荷监控实用有效。     

Crystal orientation and morphology of a lamellae in wrought titanium alloys: On the role of microstructure evolution in b processing

To obtain high-quality aviation forgings of titanium alloys, b forging is an essential processing step which must be considered throughout a production process. In this work, the effect of b forging on the crystal orientation and morphology of lamellar a was experimentally investigated in a two-phase titanium alloy. Strong dynamic recovery during b working resulted in the formation of low-angle grain boundary(LAGBb) inside b grains. The lamellar a can penetrate through the LAGBb, leading to similar intra a LAGBs on subgrain boundaries. Deformation banding occurs at high strain rates, and both diffusive and sharp boundaries of deformation bands can be observed.A continuous change of the b orientation in diffusive boundaries results in the formation of fine and disordered a lamellae without intra-lamellar boundary to hold the Burgers orientation relationship(OR). On sharp boundaries, it is prone to producing continuous grain boundary a(aGB) with a highly similar orientation along the boundaries. Meanwhile, there may exist several lower-angle boundaries within the grain boundary a for a smoother orientation change on the b grain boundary.     

A comprehensive study of the 2016 Mw 6.0 Italy earthquake based on high-rate (10 Hz) GPS data

The 2016 M_w 6.0 Italy earthquake is successfully recorded by the near-field 10?Hz GPS and 200?Hz Strong Motion (SM) stations, providing valuable data for this study. A comprehensive study of this earthquake is carried out based on GPS data, which contains coseismic deformations analysis, noise analysis, seismic wave picking, and magnitude determination. The noise of most GPS-derived displacement waveforms can be described as a combination of white noise, flicker noise, and random walk noise after the earthquake occurrence, and the spectral indices vary significantly for most stations, implying that the seismic signals have affected the noise characteristic of GPS-derived displacement waveforms. S-transform is employed to assess the GPS capability to detect the seismic arrival time. The SM station AMT and the GPS station AMAT are in good agreement in seismic wave picking, and the difference is only 1.2?s in the north component, suggesting that the outcome of seismic wave picking using GPS data is reliable. Then, a classic empirical formula is employed to determine the moment magnitude. A robust moment magnitude (Mw 5.90) can be estimated by the nine GPS stations with about 23.9?s. If four GPS stations near the epicenter is chosen to determine the magnitude, it only take 13.0?s to retrieve a reliable preliminary (Mw 5.82) magnitude, which is 5.4?s ahead of nine stations. In addition, Cross Wavelet Transform (XWT) is adopted to measuring the correlation and phase relationship between GPS and SM records. The result of XWT analysis indicates 10?Hz GPS is capable of capturing reliable and accurate coseismic dynamic deformations, as evidenced by the XWT-based semblance being close to 1 between GPS and SM records. The above results confirm the capability of 10?Hz GPS to capture coseismic dynamic deformations, detect seismic arrival time, and determine earthquake magnitude. Moreover, rapid magnitude determination based on 10?Hz GPS data can be regarded as an important supplement to Earthquake Early Warning (EEW).     

基于人工地标的移动机器人定位与调整技术

在飞机大型构件测量领域,针对测量设备自动化转站时存在移动机器人无法准确到达站位的问题,提出了采用基于人工地标的移动机器人定位与调整技术实现转站时的精确定位。其次,设计了一种人工地标,给出使用激光跟踪仪的地标标定工装以及标定方法,通过该方法可得到地标在全局坐标系下的坐标。同时,介绍了地标的编码与位姿的解算方法,以及移动机器人位姿调整策略。最后,试验表明,人工地标测量的位置和角度误差均较小,移动机器人通过人工地标的定位与调整后的精度可以满足自动化转站的精度要求。