Ku波段波导扫频双六端口网络分析仪

介绍研制的一种实用Ku波段扫频双六端口网络分析仪。该仪器能同时测量双口网络的4个散射参数及单口网络的复反射系数。     

连续自由流电泳微重力下分离模式蛋白质的研究

以连续自由流电泳的区带电泳模式分离血红蛋白和细胞色素C，比较了不同缓冲液甘油浓度下的分离效果，确定了最终装载在神舟4号飞船上A3—2型电泳仪的电泳分离条件，通过地面和空间实验，初步探讨了微重力对连续自由流电泳分离的影响，并对电泳的分离产物做了多种检测．     

MATLAB在飞机环境控制系统仿真中的应用

介绍了在MATLAB环境下,对飞机环境控制系统的建模方法,开发了飞机环控系统综合仿真的MATLAB工具箱.简单介绍了所开发的仿真工具箱,并且用此工具箱对某型飞机的环控系统进行了仿真研究,与实验结果的对比表明,所开发的工具箱,具有很高的仿真精度.     

亚、超音速机翼非定常广义气动力系数之间的关系

 <正> 研究弹性飞机的动力学特性应计及非定常广义气动力。为了尽可能保留非定常运动历程,应首先计算由阶跃函数形式下洗产生的非定常气动力函数(指示函数或指数函数),再利用卷积形式的迭加原理处理任意函数形式下洗产生的非定常气动力。用振型法建立飞机弹性运动方程,可将飞机上任一质点的弹性位移近似地表示为     

飞机壁板结构的声疲劳计算及试验

 <正> 飞机结构所承受的噪声载荷声压级超过130dB时,经较长时间激励,往往在噪声诱导应力较大的区域里产生疲劳破坏。而在各种类型的结构件中声疲劳破坏的相对发生率以蒙皮壁板结构为最高。 本文采用矩形铝合金平板来模拟蒙皮壁板结构,对其进行了声疲劳寿命计算与试验研究.     

喷管扩张段烧蚀的“台阶效应”计算

当喉衬和扩张段内衬采用具有不同烧蚀率的材料时,常出现“台阶效应”.本文以气动热化学烧蚀机理为基楚,提出应用适当的对流换热和加剧的化学反应计算对台阶效应区进行修正的方法,使台阶效应区的烧蚀率预示更切合实际工况.     

钛合金胶接点焊接头的性能检测

研究了不同焊接电流下钛合金板胶接点焊接头的A扫描信号和C扫描图像特征,并进行了拉伸-剪切试验。结果表明:通过观察C扫描图像的特征与A扫描信号的变化,能够划分胶接点焊接头的胶层区、热影响区、熔合区、熔核区以及焊接缺陷;随着电流(7~10 k A)的逐渐增大,接头熔核直径呈递增趋势,相应的失效载荷从7 231.5增加到10 939.0 N;当电流为7 k A时,在C扫描图像上反映出飞溅缺陷,此时接头失效载荷远小于没有出现飞溅的接头,可见飞溅降低了胶接点焊接头的拉剪载荷。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

无人水面艇海洋调查国内应用进展与展望

针对浅水区、污染区、极地等复杂海洋环境，传统海洋调查手段劳动强度高、安全风险大、作业效率低。无人水面艇具备无人、高效等特点，非常适合在上述复杂海洋环境中作业，并于近年来在海洋调查领域中得到了快速发展与广泛应用。从海洋调查领域中无人水面艇的优势、国内外典型的无人水面艇和应用案例入手，深入分析了我国无人水面艇海洋调查的现状，并对未来的技术发展方向进行了展望。实践表明，应用无人水面艇进行海底地形地貌调查的技术已基本成熟，水深数据质量和自主导航精度均可满足规范要求。在未来，须将无人水面艇的应用进一步扩展至物理海洋、海洋生物、海洋化学等专业领域，并加快研制基于可再生能源的长航程无人水面艇，以开展全球性海洋调查。     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.