Initial closed operation of the CELSS Test Facility Engineering Development Unit.

As part of the NASA Advanced Life Support Flight Program, a Controlled Ecological Life Support System (CELSS) Test Facility Engineering Development Unit has been constructed and is undergoing initial operational testing at NASA Ames Research Center. The Engineering Development Unit (EDU) is a tightly closed, stringently controlled, ground-based testbed which provides a broad range of environmental conditions under which a variety of CELSS higher plant crops can be grown. Although the EDU was developed primarily to provide near-term engineering data and a realistic determination of the subsystem and system requirements necessary for the fabrication of a comparable flight unit, the EDU has also provided a means to evaluate plant crop productivity and physiology under controlled conditions. This paper describes the initial closed operational testing of the EDU, with emphasis on the hardware performance capabilities. Measured performance data during a 28-day closed operation period are compared with the specified functional requirements, and an example of inferring crop growth parameters from the test data is presented. Plans for future science and technology testing are also discussed.     

Development of an advanced rocket propellant handler's suit.

Most launch vehicles and satellites in the US inventory rely upon the use of hypergolic rocket propellants, many of which are toxic to humans. These fuels and oxidizers, such as hydrazine and nitrogen tetroxide have threshold limit values as low as 0.01 PPM. It is essential to provide space workers handling these agents whole body protection as they are universally hazardous not only to the respiratory system, but the skin as well. This paper describes a new method for powering a whole body protective garment to assure the safety of ground servicing crews. A new technology has been developed through the small business innovative research program at the Kennedy Space Center. Currently, liquid air is used in the environmental control unit (ECU) that powers the propellant handlers suit (PHE). However, liquid air exhibits problems with attitude dependence, oxygen enrichment, and difficulty with reliable quantity measurement. The new technology employs the storage of the supply air as a supercritical gas. This method of air storage overcomes all of three problems above while maintaining high density storage at relatively low vessel pressures (<7000 kPa or approximately 1000 psi). A one hour prototype ECU was developed and tested to prove the feasibility of this concept. This was upgraded by the design of a larger supercritical dewar capable of holding 7 Kg of air, a supply which provides a 2 hour duration to the PHE. A third version is being developed to test the feasibility of replacing existing air cooling methodology with a liquid cooled garment for relief of heat stress in this warm Florida environment. Testing of the first one hour prototype yielded data comparable to the liquid air powered predecessor, but enjoyed advantages of attitude independence and oxygen level stability. Thermal data revealed heat stress relief at least as good as liquid air supplied units. The application of supercritical air technology to this whole body protective ensemble marked an advancement in the state-of-the-art in personal protective equipment. Not only was long duration environmental control provided, but it was done without a high pressure vessel. The unit met human performance needs for attitude independence, oxygen stability and relief of heat stress. This supercritical air (and oxygen) technology is suggested for microgravity applications in life support such as the Extravehicular Mobility Unit.     

Energy storage at 77 K in multilayer ceramic capacitors

A ceramic material having a large dielectric constant at 77 K, ε=8000-12000, has been developed for capacitive energy storage at this temperature. A large matrix of multilayer ceramic capacitors were fabricated using conventional tape-casting methods to optimize the dielectric breakdown strength at 77 K, and measured energy storage values on these capacitors range up to 6 J/cm³ at 77 K. An unfused bank of these capacitors was voltage-cycled 10⁵ times at 77 K without failure, and the heating effects during cycling were immeasurably small (i.e., nitrogen boiloff was monitored). An electrocaloric effect on discharge (ΔT~1 K) contributes to the thermal stability. Measurements of the frequency dependence of the dielectric properties of the ceramic at 77 K indicate a fundamental limit of about 8 μs for the switching repetition rate. Improved capacitor-manufacturing methods are discussed which can increase the energy density to the 20-30 J/cm³ range     

Moving target imaging algorithm for SAR data

A digital processing algorithm for fine-resolution imaging of synthetic aperture radar (SAR) moving targets is described. The targets may have any translational and rotational motion components relative to the data collection platform. The algorithm requires the presence of up to three prominent points in the image of the target; the signals from these points provide estimates of the unknown target motion parameters. Phase compensation and data formatting based on these estimates eliminate motion-induced phase errors. This algorithm has been implemented on a VAX computer and used to process both simulated and real SAR data of moving targets. Results obtained using the simulated data are presented     

A new clutter rejection method using a robust polarimetricCFAR-detector

Two methods for constructing robust polarimetric constant-false-alarm-rate (CFAR) detectors that use elements of the scattering matrix are discussed. Both methods use robust estimators to recognize outliers and exclude them from further calculations. The first method weighs each sample of the surrounding vectors, and vectors that appear to be outliers are weighted with lower values than the others. The second method uses cluster algorithms to arrange the data in different clusters; some clusters contain the outliers, and others contain observations assumed to come from the main body of the data. The detectors are intended to be used in multitarget and nonhomogeneous-clutter environments     

Next generation digital GPS receiver

The architecture and technology features of the next-generation (NGR) digital GPS (Global Positioning System) receiver manufactured by Collin are described. The project's objective was to develop an advanced GPS receiver chipset with high antijam capabilities. The program, initiated in 1985, has provided the technology for miniature receiver products for both unmanned and manned vehicle applications. A two-channel version of the receiver is in full-scale development for tactical missile applications. A five-channel version is being tested and evaluated as a drop-in replacement for RCVR-3A, the US Department of Defense standard high dynamic receiver. The NGR design started with the digital signal processing architecture developed for the Defense Advanced Research Project Agency (DARPA) hand-held GPS receiver. Enhancements were made to improve the antijam and signal acquisition performance. Producible, qualifiable and cost-effective silicon monolithic microwave integrated circuits and semicustom digital technologies were used to develop the core GPS chipset. A system design approach was established to permit reuse of mature and validated GPS software     

A nickel/hydrogen battery for PV systems

The nickel-hydrogen battery, developed in the early nineteen-seventies as an energy-storage subsystem for commercial communication satellites, is discussed. The advantages offered by nickel-hydrogen batteries, including long life, low maintenance and high reliability, make it very attractive for terrestrial applications such as stand-alone photovoltaic systems. The major drawback to the wider use of the nickel-hydrogen battery is its high initial cost. A 7-kWh battery has been on test since January 1988 using a flat-plate photovoltaic array for charging. The cell, battery design and test methods are briefly described, and the results of cycling and solar tests are presented. It is concluded that the battery is well suited for remote solar applications