POSS 催化剂改性氰酸酯复合材料的性能

通过POSS 催化剂改性氰酸酯树脂,并采用热熔法排布制备了碳纤维/ 中温固化氰酸酯预浸料, 验证了改性氰酸酯的工艺性。同时考察了氰酸酯树脂及其复合材料的性能。结果表明, POSS 催化剂的加入, 降低了氰酸酯的固化温度,同时其使用温度、室温及-18℃的储存性能和复合材料力学性能与改性前相当。     

复合材料缠绕气瓶可靠性验证技术

根据航天器用复合材料气瓶高可靠性特点,对复合材料气瓶的可靠性进行了分析,气瓶的失效模式主要为泄漏和爆破,影响因素分别为疲劳寿命和承压能力,其中疲劳寿命主要受内衬影响,而承压能力主要由复合层性能决定。最后对气瓶的可靠性试验进行了描述,举例说明了气瓶的可靠度试验验证方法。     

基于DSP2812的三相SPWM波形实现

针对变频技术的核心—SPWM波形的产生和控制,详细介绍了SPWM波形的产生方法,并给出了软件编程。通过以DSP芯片TMS320F2812为核心,利用规则采样法产生SPWM波形,具有速度快,精度高,实时控制能力强,易于频率变换等优点。     

网格生成方程中非线性系数对网格正交和分布的影响研究

通过数学分析，对椭圆型方程非线性系数对生成网格的正交性和空间分布的影响进行了研究，理论分析和数值结果均表明，系数β具有控制网格正交性的作用，系数α和γ具有调节网格空间分布的作用，且其调节的强增和作用与其比值有直接关系，基于此提出了一种混合型边界条件的给定方法，较好地实现了网格正交和疏密分布的控制。     

Soft X-ray observations of helmet structures from SXT/Yohkoh

We present soft X-ray observations of helmet structures in solar active regions obtained from SXT/Yohkoh. These helmet structures are observed to form in the flare decay phase and to be associated with active region loop interactions. Their morphology is similar to the much larger scale helmet streamers that appear in the outer corona as shown in optical images of solar eclipse. The observed X-ray helmet structures appear to be in quasi-equilibrium with lifetimes greater than the MHD time scale. Using the filter ratio method for the X-ray observations, we find that the cusp region has lower temperature and higher density than that in the stalk region above it. The plasma pressure in the cusp region is about the same or slightly higher than that in the stalk region.     

3-D position estimation of isolated target and optimal trajectory choice in parasitic synthetic aperture radar

Bistatic SAR (BSAR) systems have recently been the subject of several studies, but little attention has been given to the potential of the location of targets. In the paper, the performance of the estimation of 3-D position of a target (TPE) in parasitic SAR is obtained analytically and illustrated by computer simulation using ambiguity function analysis, and the maximum likelihood estimate (MLE) approach. It was shown that by using a multi look parasitic BSAR all three coordinates of an isolated point target (IPT) could be evaluated. Analytical closed form equations that characterize the measurement accuracy were derived. In the final these equations will be used to demonstrate various cases of more practical, including optimal trajectories choice under any geometry configuration case, moreover, the conclusion is verified via Matlab.     

叉流管－管型换热器二维温度场的数值分析

建立并导出叉流管－管型换热器传热过程的二维数学模型及相应的差分格式。对比实验数据和性能计算结果，表明数值方法是有效可行的，据此编制的计算机程序已成功地用于组合发动机空气预冷换热器工作过程的预测。     

Adaptive control for a sensorless permanent-magnet synchronousmotor drive

An adaptive velocity controller for a permanent-magnet synchronous motor without using shaft sensor is presented. Two line-to-line voltages and two stator currents are sensed to produce the flux position. The design part is concerned with the formulation of control algorithm for current-regulated pulsewidth modulated inverter and vector control strategy for speed loop. Under the vector control framework, self-tuning, model following, and model referencing adaptive control are applied to design for the speed-loop controllers. The implementational part integrates the control of current and speed loop using microprocessor-based controllers. Experimental case studies that correlate simulation and measurement results are provided. The experimental results validate the theoretical development. A new approach for designing advanced adaptive controller for a sensorless ac drive is provided     

氦气驱动预压涡轮泵启动初期反流问题分析

用于某液体火箭发动启动动系统的气驱预压涡轮泵在起动初期出现了气体反流,导致预压泵呈夹气状态,对发动启动动过程控制不利。根据驱动试验系统原理,在MWorks平台中对驱动过程进行了仿真。对预压泵采用了Suter全特性表达式,对涡轮管路及排放路分别建立了描述排空与两相流动过程的简化数学模型。结果 表明,导致反流的原因为涡轮入...