关于飞机性能可靠性的探讨

从保持现役飞机战斗力出发,首次提出了飞机飞行性能可靠性概念,并将飞行性能可靠性分为严（狭义）飞行性能可靠性和宽（广义）飞行性能可靠性两类进行讨论研究。在此基础上,给出了飞行性能可靠性的评估方法,并对开展飞机飞行性能可靠性的研究工作提出了建议。可供部队、厂、所在设计和使用中参考。     

片梭织机的提速及其改造

从片梭织机的结构、性能、织造工艺和织机调试等方面入笔,分析了影响片梭织机提速的有关因素,提出了为合理提速而对织机所采取的改造方法。     

FMS的对象建模

进行FMS建模研究是研究FMS动态仿真软件的自动生成的前提.面向对象源于仿真,采用面向对象的建模方法,在FMS的分析、建模以及动态调度软件自动生成有着极大的优越性.本文首先研究了对象建模的方法,并以之为指导,建立了FMS的对象模型、功能模型和动态模型,为FMS动态仿真软件的自动生成打下了基础.     

振动辅助钻削对CFRP/钛合金叠层结构孔径阶差影响规律实验研究

在飞机部件装配过程中,CFRP/钛合金叠层结构的连接十分常见,而由于两种材料迥然不同的材料性能,导致制孔后存在孔径阶差,严重影响了CFRP/钛合金结构的疲劳强度。本文开展了低频轴向振动辅助钻削的正交实验,分析了低频振动辅助钻削工艺参数与切削力和切屑形态的关系以及工艺参数对CFRP/钛合金孔径阶差的影响。结果表明,由于低频振动辅助钻削刀具的周期性进给,钛合金切屑由连续长切屑变为扇形短屑,减少了对CFRP的扩孔效应,钻削区域切削热降低,平均轴向力降低;另外,振幅和进给量对孔径阶差的影响较为显著,而主轴转速的影响较小,且孔径阶差随着振幅的增大先减小后增大,随着进给量的增大而增大。通过试验验证和分析,确定面向孔径控制的最优工艺参数组合方案：主轴转速为600 r/min、进给量为0.02 mm/r、振幅为150μm。     

厚覆冰导线升力突变机理及数值模拟研究

针对新月形厚覆冰导线的升力系数在风攻角15°附近存在突变的问题,分别采用基于k-ωSST湍流模型的雷诺时均法和大涡模拟(LES)的数值方法对新月形厚覆冰导线在风攻角10°～20°范围进行了模拟.通过对比两种数值方法计算得到的覆冰导线气动力系数、流场结构和表面风压,发现LES方法能够更好地捕捉新月形覆冰导线表面的小尺度涡...     

Comparative analysis of four different single-frequency PPP models on positioning performance and atmosphere delay retrieval

Single-frequency precise point positioning (SF-PPP) has attracted increasing attention due to its high precision and cost effectiveness. With various strategies to handle the dominant error, i.e., ionosphere delay, the ionosphere-float (IF), ionosphere-free-half (IFH), ionosphere-corrected (IC), and ionosphere-weighted (IW) SF-PPP models are certain to possess different characteristics and performance levels. This study is dedicated to assessing and comparing the four models from model characteristics, positioning performance, and atmosphere delay retrieval. The model comparison shows that IC and IW models are full-rank while IF and IFH models have a rank deficiency of size one that will result in biased estimations, which means the better solvability of IC and IW models. The experiments are carried out based on the 7-day Global Positioning System (GPS) observations collected at 57 global Multi-GNSS Experiment (MGEX) stations and Global Ionosphere Map (GIM) products. The results indicate that the IW model can accelerate SF-PPP convergence and achieve higher positioning accuracy compared to the other three SF-PPP models, especially in kinematic mode. With convergence criteria of 0.25 m in horizontal and 0.5 m in vertical, the east/north/up convergence times of IW model are 0.5/15.0/25.0 min and 0.5/16.0/36.5 min for static and kinematic modes, respectively. The IW model is able to achieve an instantaneous positioning accuracy of 0.28/0.35/0.75 m. In addition, a real kinematic test also demonstrates the best positioning solutions of IW model. Regarding troposphere delay retrieval, the IF, IFH, and IW models obtain a comparable daily accuracy of 3.0 cm on average, while the IC model achieves the worst accuracy of 8.0 cm. For precise ionosphere delay estimation, IW model only needs an average initialization time of 34.3 min, but a longer initialization time of 51.6 min is required for IF model. The daily precision of ionosphere delay estimation for IW model can reach up to 10.8 cm. At the present accuracy of GIM products, it is suggested that the IW model should be adopted for SF-PPP first due to its superior performance in positioning and atmosphere delay retrieval.     

硅橡胶基防热涂层动态烧蚀行为及机理研究

针对两种典型硅橡胶基防热涂层开展高温燃气流烧蚀实验，通过对烧蚀后涂层的宏观及微观形貌分析，探讨了其防隔热机理及烧蚀模型。研究结果表明：烧蚀后两种涂层均存在液态层、陶瓷层、热解层以及原始层；烧蚀过程中甲基苯基硅橡胶涂层主要发生主链“回咬”成环反应，导致树脂基体交联密度降低，力学性能下降，涂层外表面发生开裂，甲基乙烯基硅橡胶涂层则主要发生侧基交联反应，使树脂基体交联密度上升，促进涂层发生陶瓷化转变；热辐射、热容吸热、热解反应吸热以及热阻塞效应为四种主要的热耗散机制，质量损失产生的原因主要包括反应气体释放以及气动剪切力导致的机械剥蚀。     

Comparison of convergence time and positioning accuracy among BDS,GPS and BDS/GPS precise point positioning with ambiguity resolution

Precise point positioning (PPP) usually takes about 30?min to obtain centimetre-level accuracy, which greatly limits its application. To address the drawbacks of convergence speed and positioning accuracy, we develop a PPP model with integrated GPS and BDS observations. Based on the method, stations with global coverage are selected to estimate the fractional cycle bias (FCB) of GPS and BDS. The short-term and long-term time series of wide-lane (WL) FCB, and the single day change of narrow-lane (NL) FCB are analysed. It is found that the range of GPS and BDS non-GEO (IGSO and MEO) WL FCB is stable at up to a 30-day-time frame. At times frame of up to 60?days, the stability is reduced a lot. Whether for short-term or long-term, the changes in the BDS GEO WL FCB are large. Moreover, BDS FCB sometimes undergoes a sudden jump. Besides, 17 and 10 stations were used respectively to investigate the convergence speed and positioning errors with six strategies: BDS ambiguity-float PPP (Bfloat), GPS ambiguity-float PPP (Gfloat), BDS/GPS ambiguity-float PPP (BGfloat), BDS ambiguity-fixed PPP (Bfix), GPS ambiguity-fixed (Gfix), and BDS/GPS ambiguity-fixed (BGfix). The average convergence speed of the ambiguity-fixed solution is greatly improved compared with the ambiguity-float solution. In terms of the average convergence time, the Bfloat is the longest and the BGfix is the shortest among these six strategies. Whether for ambiguity-float PPP or ambiguity-fixed PPP, the convergence reduction time in three directions for the combined system is the largest compared with the single BDS. The average RMS value of the Bfix in three directions (easting (E), northing (N), and up (U)) are 2.0?cm, 1.5?cm, and 5.9?cm respectively, while those of the Gfix are 0.8?cm, 0.5?cm, and 1.7?cm. Compared with single system, the BDS/GPS combined ambiguity-fixed system (BGfix) has the fastest convergence speed and the highest accuracy, with average RMS as 0.7?cm, 0.5?cm, and 1.9?cm for the E, N, U components, respectively.