Ti3Al基合金室温拉伸形变机制的研究

在透射电子显微镜上，利用双倾双束技术和不可见判据，分析了Ｔｉ－２５Ａｌ－１０Ｎｂ－３Ｖ－１Ｍｏ（ａｔ－％）合金中具有ＤＯ１９结构的α２相在室温拉伸形变时的位错类型和滑移系。证明，α２相在室温拉伸形变时，主要开动的是型位错的滑移系，例如＜１１２０＞｛１１００｝＜１１２０＞｛０００１｝和少量以位错对存在的型位错滑移系，如＜１１２６＞｛２０２１｝。     

雾化效果对脉冲爆震室性能影响的实验研究

进行了用冷态实验模拟爆震室中雾化性能的研究。实验中,采用水/压缩空气模拟煤油/氧气,测试了与爆震试验供应压力一致的各工况下的混合物索太尔平均直径(SMD)。研究结果表明:随着空气压力、水压力的增大,SMD减小;所建立的冷态雾化和混合实验台可以满足模拟热态实验雾化效果的需要,且带头部离心喷嘴的爆震性能好于直射喷嘴的。     

无加力涡扇发动机二元喷管的红外辐射特性实验

对轴对称喷管和一组长宽比分别为1,4,8,12和16的二元喷管进行了红外辐射特性测试实验研究。喷管中的气流由主流燃气和次流空气组成,用以模拟涡扇发动机的喷管。得出了二元喷管的红外辐射强度的空间分布,并且将二元喷管和轴对称喷管的红外辐射强度进行了比较。      

Experimental Investigation of Nozzle Effects on Thrust and Inlet Pressure of an Air-breathing Pulse Detonation Engine

Nozzle effects on thrust and inlet pressure of a multi-cycle air-breathing pulse detonation engine (APDE) are investigated experimentally. An APDE with 68 mm in diameter and 2 050 mm in length is operated using gasoline/air mixture. Straight nozzle, converging nozzle, converging-diverging nozzle and diverging nozzle are tested. The results show that thrust augmentation of converging-diverging nozzle, diverging nozzle or straight nozzle is better than that of converging nozzle on the whole. Thrust augmentation of straight nozzle is worse than those of converging-diverging nozzle and diverging nozzle. Thrust augmentations of diverging nozzle with larger expansion ratio and converging-diverging nozzle with larger throat area range from 20% to 40% on tested frequencies and are better than those of congeneric other nozzles respectively. Nozzle effects on inlet pressure are also researched. At each frequency it is indicated that filling pressures and average peak pressures of inlet with diverging nozzle and converging-diverging nozzle with large throat cross section area are higher than those with straight nozzle and converging nozzle. Pressures near thrust wall increase in an increase order from without nozzle, with diverging nozzle, straight nozzle and converging-diverging nozzle to converging nozzle.     

超高温陶瓷基复合材料制备工艺研究进展

对超高温陶瓷作了简要介绍,综述了先驱体浸渍裂解(PIP)、反应熔体浸渗(RMI)、化学气相渗透(CVI)、泥浆法(SI)等工艺的最新研究进展。     

自吸气脉冲爆震发动机超声速进气道气动性能的数值研究

采用有限体积法计算了某轴对称超声速进气道,在不同幅度和频率的出口扰动压强下的进气道内结尾正激波的运动情况,得出了进气道内结尾正激波运动特性和扰动压强的频率和幅度的关系。在计算中,本文采用了多块结构化网格,控制体积的界面无粘通量采用三阶迎风格式插值获得,同时采用了minmod通量限制器,以确保在激波处的解的物理特性;扩散通量采用二阶中心差分格式插值获得。定常计算采用当地时间步法,非定常计算采用双时间步法。离散的代数方程采用交替方向迭代法求解。     

二维对流—扩散方程的控制体有限元法数值模拟

推导了二维对流—扩散方程的控制体有限元公式，其主要特点是所得离散化方程适合于逐点迭代法及共轭梯度法进行求解，使得该方法更适合于求解复杂的几何域及节省更多的计算机内存。通过几个算例表明，该方法对于特别大的Ｐｅｃｌｅｔ数其精度也是很高的     

Monocular Vision-based Two-stage Iterative Algorithm for Relative Position and Attitude Estimation of Docking Spacecraft

Visual sensors are used to measure the relative state of the chaser spacecraft to the target spacecraft during close range rendezvous phases. This article proposes a two-stage iterative algorithm based on an inverse projection ray approach to address the relative position and attitude estimation by using feature points and monocular vision. It consists of two stages: absolute orientation and depth recovery. In the first stage, Umeyama's algorithm is used to fit the three-dimensional (3D) model set and estimate the 3D point set while in the second stage, the depths of the observed feature points are estimated. This procedure is repeated until the result converges. Moreover, the effectiveness and convergence of the proposed algorithm are verified through theoretical analysis and mathematical simulation.     

均匀化处理对TiAl 合金铸造组织的影响

研究了均匀化处理对两种含B的铸造TiAl合金铸造组织的影响。研究发现1 370℃/5 min/OQ+1150℃/6 h/AC均匀化热处理能有效消除B2相,将b稳定化元素固溶到基体中,实现成分均匀化;1 370℃/5 min/OQ+1 150℃/24 h/AC均匀化热处理后可使粗大的铸造片层组织分解转变为细晶近g组织,平均晶粒直径50mm。     

喷雾运动初始条件问题的研究

根据所完成的流动环境中颗粒在初始区域内速度分布的测量结果，对颗粒运动初始条件的问题进行了全面的研究，提出了统计性，随机性和确定性的三种初始条件及其数学处理方法，在此基础上，应用喷雾两相流的数值方法，计算了喷雾的运动，比较了不同初始条件对计算结果的影响，并将所得计算结果与实验结果做了比较，两者符合较好。