Investigations of the Mars Upper Atmosphere with ExoMars Trace Gas Orbiter

Space Science Reviews - Time measured by an ideal clock crucially depends on the gravitational potential and velocity of the clock according to general relativity. Technological advances in...     

五自由度磁悬磨头电控系统研究

研究的高速磨床电磁悬浮磨头电控系统尽量采用最新技术，在保证系统 性能的前提下降低了系统造价。在该系统中采用TMS320F240 DSP芯片作为控制核心，同时控制磁悬浮轴承的悬浮和变频电机调速，采用运行效率很高的汇编语言编写控制软件，其中磁悬浮轴承是PID控制算法，电机调速为SPWM方式。磁悬浮轴承PWM功率放大器中采用能简化驱动的新型半桥电路，电机调速主电路中采用智能功率模块（IPM）。动态刚度测试和高速运转实验表明，该电控系统满足高速磨床电磁悬浮磨头的控制要求。     

Simulation of the flow around a stationary circular cylinder taking into account laminar-turbulent transition

We consider a problem of a stationary incompressible viscous fluid flow around a flat circular cylinder. In the vicinity of the critical Reynolds number Re _cr a stepwise drop of the cylinder drag takes place, which is called the drag crisis.     

Solid nanomembrane manufacture using ion-plasma action

A process of manufacture of porous membranes made of aluminum foil (Al 99.99%) by the method of electrochemical anodic oxidation followed by a continuous barrier layer removal with ion-plasma irradiation is described. The membranes having a 8 mm diameter made from AL2O3 with a thickness from 2 to 5 microns thick with a regular channel arrangement are obtained. A possibility to change the channel diameter in the range of 20?C100 nm by adjusting voltage and temperature during the oxidation is shown. We present the experimental dependencies of aluminum and aluminum oxide sputtering coefficients on the energy and incidence angle of xenon ions within the energy range of 100??400 eV.     

Buckling of composite panels: A criterion for optimum stiffener design

In this paper a linear, closed-form analysis of the buckling behavior of an orthotropic plate with elastic clamping and edge reinforcement under uniform compressive load is presented. This is a typical structural situation found in aerospace engineering for instance as stiffeners in wings or the fuselage. All governing equations are transformed in a dimensionless system using common characteristic quantities to gain good analytical access. The buckling behavior is analyzed and generic buckling diagrams are presented. The solutions show excellent agreement with results from literature and numerical analyses.The minimum bending stiffness of the edge reinforcement needed to withstand buckling is examined and a minimum stiffness criterion is presented. Furthermore an absolute minimum bending stiffness is found which is sufficient to enable the reinforcement to act as a near-rigid support for arbitrarily long plates. These criteria are of interest for optimized lightweight design of stringers and stiffeners.     

A software package for computer-aided design analysis of thin-walled structures from composite materials

An algorithm of analyzing the design parameters for a thin-walled wing from composite material based on the efficient distribution of structural material between load-carrying elements is described. We consider the problems of convergence acceleration for the iteration design analysis. Also presented are the examples of determining the design parameters for a superlight aircraft wing and the rational parameters of the filler in the form of a three-dimensional rod structure.     

Water feed influence on nitric oxide emission under oxidation of near-stoichiometric air-methane mixtures

We considered the influence of temperature on the nitric oxide emission under combustion of the near-stoichiometric mixtures with and without water feed. We revealed the advantage of the method of fuel-water-air mixture combustion over that of the leaned mixture combustion.     

Systems for the indication and display of secondary information in avionics and autobasing complexes

We consider the peculiarities of application for the cabin indicating systems of secondary information display, formulate and systematize the compositional and technical requirements for display systems and their elements. The tendencies and lines in the development of head-up displays for avionics and autobasing complexes were determined. The technique of calculating optics of such display systems with the use of electronic distortion compensation is presented.     

Solar Irradiance Variability Since 1978

Since November 1978 a set of total solar irradiance (TSI) measurements from space is available, yielding a time series of more than 25 years. Presently, there are three TSI composites available, called PMOD, ACRIM and IRMB, which are all constructed from the same original data, but use different procedures to correct for sensitivity changes. The PMOD composite is the only one which also corrects the early HF data for degradation. The results from the detailed analysis of the VIRGO radiometry allow a good understanding of the effects influencing the long-term behaviour of classical radiometers in space. Thus, a re-analysis of the behaviour of HF/NIMBUS-7 and ACRIM-I/SMM was indicated. For the former the situation is complicated by the fact that there are no in-flight means to determine changes due to exposure to solar radiation by comparison with a less exposed radiometer on the same spacecraft. The geometry and optical property of the cavity of HF is, however, very similar to the PMO6-type radiometers, so the behaviour of the PMO6V radiometers on VIRGO can be used as a model. ACRIM-I had to be revised mainly due to a henceforth undetected early increase and a more detailed analysis of its degradation. The results are not only important for solar radiometry from space, but they also provide a more reliable TSI during cycle 21. The differences between the revised PMOD composite and the ACRIM and IRMB are discussed by comparison with a TSI reconstruction from Kitt-Peak magnetograms. As the PMOD composite is the only one which has reliable data for cycle 21, the behaviour of the three solar cycles can now be compared and the similarities and differences discussed.     

Spherical accretion of massive black holes: A model for galactic nuclei

The possibility of explaining the continuous emission of active galactic nuclei in the frame of a model of spherical accretion onto a massive black hole is discussed. Cool inhomogeneities (T 10⁴°K) within the accretion flow could be responsible for the broad line emission if half of the accreting matter is in the dense phase. A crucial test of this hypothesis is the expected correlation between the ratio of the luminosity in lines to the total luminosity and the hardness of the continuous spectrum.