细晶铸造K418B合金热处理工艺研究

研究了不同热处理工艺与 K41 8B合金细晶铸件组织和性能的关系 ,结果表明 ,合金组织中的γ′相大小和晶界上次生碳化物的形态和分布对中温持久性能具有重要影响。提出了 K41 8Β合金细晶铸件合适的真空热处理制度为 :1 1 80℃ / 2 h,AC 93 0℃ / 1 6h,AC     

金翼医院管理信息系统简介及推广中遇到的问题与思考

简要介绍了金翼医院管理信息系统 (JinYiHospitalManagementInformationSystem)功能及在推广应用过程中遇到的问题 ,对如何解决这些问题 ,提出了一些建议 ,从而使HMIS得到进一步推广应用     

一类高阶有理差分动力系统

讨论了高阶有理差分方程xn 1=(αxn-k 1)/(-1 xnxn-1…xn-k 1),for n=0,1,…,其中α<0,k∈{1,2,…},x-k 1,…,x0都是实数,并且使得x-k 1…x0≠1。给出了这类方程解的明确表达式,并对其解的稳定性和收敛性也做了进一步讨论。     

A theoretical model of semi-elliptic surface crack growth

A theoretical model of semi-elliptic surface crack growth based on the low cycle strain damage accumulation near the crack tip along the cracking direction and the Newman–Raju formula is developed. The crack is regarded as a sharp notch with a small curvature radius and the process zone is assumed to be the size of cyclic plastic zone. The modified Hutchinson, Rice and Rosengren(HRR) formulations are used in the presented study. Assuming that the shape of surface crack front is controlled by two critical points: the deepest point and the surface point.The theoretical model is applied to semi-elliptic surface cracked Al 7075-T6 alloy plate under cyclic loading, and five different initial crack shapes are discussed in present study. Good agreement between experimental and theoretical results is obtained.     

RapidIO交换互连与配置管理研究

RapidIO技术以交换机为核心构建互连拓扑系统,基于交换机的RapidIO互连与配置管理是整个RapidIO互连系统实现的关键技术。介绍了基于RapidIO交换的互连技术,阐述了RapidIO交换网络JTAG接口、I2C接口和RapidIO维护包等三种配置管理方法和具体的实现方式,可以完成系统的动态流量调节、容错重构等特性。     

一种动态电源供电系统的设计实现方法

为将动态电压调整技术应用于设计中进行功耗优化,阐述了动态电源调整技术、电压识别技术、PMBus总线等基础知识,提出了一种动态电源供电系统的设计方案。采用UCD9222控制器和UCD7242驱动器的设计实例,介绍了动态电源供电系统的配置管理和实现方法,实现了对处理器内核供电电压的动态供电,具有通用性和易用性等优点,可以有效降低系统功耗,满足动态电源供电的设计需求。     

直升机动态着舰流场下的旋翼气动载荷分析

直升机着舰流场复杂多变,严重影响着旋翼的气动环境,进而影响直升机着舰安全。本文基于计算流体力学(Computational fluid dynamics,CFD)技术建立了一个直升机动态着舰的数值模拟方法,并以此研究直升机着舰过程中的气动载荷变化。该方法以N-S方程作为控制方程,并选取k-ω湍流模型来提高对涡流场的捕捉精度,采用动量源方法模拟旋翼。应用所建立的方法,着重分析了直升机侧弦进场、垂直降落过程中的耦合流场特征和气动载荷变化。结果表明:直升机侧弦进场时旋翼会与甲板舷涡以及舰船艉部的涡回流区发生较强的涡干扰,导致拉力显著降低,在舰面效应的影响下易产生一个附加的滚转力矩,影响直升机姿态稳定;垂直降落时在上述干扰的综合作用下,旋翼拉力呈现出先减小、后增大的特点,各气动载荷在接近甲板时会出现剧烈的波动,加大了着舰风险。     

模型的随机平衡降阶

本文提出了系统在白噪声激励下的一种开环降阶方法—随机平衡降阶法。在系统的随机平衡坐标中，输出性能指标可以表示成一组与系统随机可控／可观格莱姆相关的贡献值的和。根据这组贡献值的大小，可以决定在随机平衡坐标下降阶模型所要保留的状态分量，并从输出误差指标的最优角度出发，对输出矩阵作个修正。最后给出了一个数值仿真例子。     

单音干扰下扩频测控信号伪码跟踪性能研究

扩频测控信号的伪码跟踪性能直接关系到测控系统的测距精度。以伪码跟踪环中鉴相曲线平衡点的过零偏移为研究对象,推导了音频干扰条件下扩频测控信号伪码跟踪的干扰最大误差;并针对干扰最大误差需考虑具体鉴相算法的特点,提出基于相关曲线主瓣的二阶中心矩扩展因子的性能评价方法。该方法利用伪码相关曲线主瓣在干扰前后的畸变情况,反映干扰对伪码跟踪性能的影响。仿真分析表明,干扰最大误差的理论及仿真结果和二阶中心矩扩展因子所得结论一致,从而验证了干扰最大误差理论的正确性以及所提性能指标的有效性。     

Experimental study of a flush wall scramjet combustor equipped with strut/wall fuel injection

In this study a flush wall scramjet combustor is tested in a supersonic incoming air flow with the Mach number of 3 which is generated by an air vitiation heater producing the stagnation temperature of 1505 K. Using liquid kerosene as the fuel, the flame is stabilized by means of a centrally mounted O₂ pilot strut after being ignited by a plasma torch. During experimental measurements, the fuel is injected with a constant equivalence ratio of 0.8 according to specified strut/wall injection ratios, i.e., a portion of the fuel amount is injected from the strut while the rest is injected from the wall. The strut and wall injectors are arranged at the same axial position. The combustion performance and wall temperature gradients are evaluated with various fuel feeding ratios between the wall and the strut. Experimental results show, when the equivalence ratio is constant and the axial injection position is fixed, the combustion characteristics vary significantly with the strut/wall fuel feeding ratio, especially when this ratio is close to its lowest and highest limits. Among the four fuel feeding ratios examined, the strut only injection mode and the average distributed strut/wall injection mode show the best combustion performance. However, the strut/wall injection mode produces a smaller wall temperature gradient compared to the strut only injection mode, which is due to the significant film cooling effect caused by the wall injected liquid kerosene.