多充液贮腔航天器耦合动力学与姿态控制

基于已有的质心面液体大幅晃动等效力学模型，采用拉格朗日方法，系统地建立了任意复杂激励下四贮腔航天器刚-液耦合动力学精确模型。由本文方法所得到的等效晃动力及晃动力矩与通过Flow3D计算出的相应结果吻合良好，验证了所建模型的可靠性。根据所建立的大幅晃动类充液航天器耦合系统动力学模型进一步研究了该类航天器在进行三轴稳定姿态机动时的主要动力学耦合特性，并设计了一类抑制姿态振荡的补偿控 制器。     

航天器项目群管理模式探讨

阐述了我国现有航天器多项目管理的模式和特点,在分析我国航天器项目管理发展基础上,根据航天器研制任务急剧增长的情况提出了项目群管理的概念和项目群管理模式的思路,为寻找更好的适合航天器快速发展的项目管理方法提供参考。     

Creep Behaviors of FGH95 Powder Ni-Base Superalloy

This article makes an investigation into the creep behavior and deformation features of FGH95 powder Ni-base superalloy by means of creep curves and microstructural observation. Results show that this superalloy exposes obvious sensibility to the applied temperature and stresses in the experimental range. Microstructure of the alloy consists of γ′ phase of various sizes and dispersed carbide particles precipitated in the wider crystal boundaries between the powder particles. During the creep, the deformation of the alloy occurs in the form of single- or double-oriented slipping inside the grains, and some of the finer carbide particles are precipitated near the slipping traces. The wide grain boundaries might be broken into the finer grains due to severe deformation. The deformation mechanism of the alloy during creep is thought to be the activation of dislocations of double-oriented slipping, including (1/2)<110> dislocation inside the γ matrix phase and <110> super-dislocation inside the γ′ phase. The formation of the stacking faults and (1/3)<112> super-Shockleys partial dislocation configuration is attributed to the decomposition of <110> super-dislocation in the γ′ phase.     

永磁同步电机转矩的最优化设计

本文首先通过Taguchi算法，筛选对永磁同步电机最大转矩影响较大的结构参数。进一步通过曲面响应法，建立最大转矩与结构参数之间的数学模型。在此基础上，利用遗传算法进行优化设计。有限元仿真和试验结果验证了上述方法正确有效。     

机翼大迎角涡破裂时气动特性计算方法的研究

本文计算了小展弦比机翼纵向和横侧气动特性,并计及涡破裂的影响。本方法以Purvis升力面理论和Polhamus吸力比拟为基础。并参照Lan方法进行大迎角特性修正。算例表明,本方法适用于小展弦比机翼气动特性的计算。     

Inner wrinkling control in hydrodynamic deep drawing of an irregular surface part using drawbeads

Inner wrinkling phenomenon is more likely to develop during hydrodynamic deep drawing （HDD） of complicated component-forms due to the higher demand for controlling deformation sequences. Aiming at the problems in control of inner wrinkling for an irregular surface part featured with both concavity and convex, this research proposes an optimal design method of drawbead parameters to change the material flow. According to theoretical analysis of the mechanism of inner wrinkling, optimizing cavity pressure only is unreasonable to form a wrinkle-free deep-drawn part, so semi-circular drawbeads are employed. The effects of layout and height of drawbeads on forming results are discussed, and a process window is established based on evaluation indicators including the anti-wrinkle coefficient and the minimum wall thickness. Experiments are carried out to validate the process window, and the wall thickness and the wrinkle height are measured and compared with numerical findings. The results show that the anti-wrinkle ability of drawbeads weakens with increasing oblique angle and distance from the die center, while the wall thickness increases with increasing oblique angle and distance, and the inner wrinkling can be completely suppressed by drawbeads arranged in zones I and II with optimum penetration.     

软件可靠性的Markov链Bayes指数模型

在充分地考虑了软件排错过程特点的基础上,将JM模型中"完全排错"的假设改为不完全排错",使之更符合实际.给出了Markov链的Bayes指数模型.利用Gibbs抽样法给出参数的Bayes估计的计算方法,以及预测分布和平均故障间隔的时间长度计算公式.     

具有无穷时滞的Volterra反应扩散系统的研究

介绍了作者在"第三届世界非线性分析学家大会"上的45分钟报告的主要内容,系统地总结了作者近几年在具有无穷时滞的Volterra反应扩散系统方面的研究成果.     

中立型非线性连续分布偏差变元微分方程的线性化振动性

研究了一类中立型非线性连续分布偏差变元微分方程和其相应的线性方程,在振动上的等价性.     

SAR成像中采用FIR滤波器校正距离弯曲的方法

雷达成像中现有的各种校正距离弯曲的方法,其运算量都太大,不能满足实时成像的要求。然而在高分 辨,宽频带SAR中,距离弯曲现象比较严重,如果不校正距离弯曲,就不能得到清晰的高分辨图像。针对这个问题,提出 一种用FIR滤波器校正距离弯曲的方法,较好地校正了距离弯曲,并明显减少了运算量,能满足实时成像系统的要求。 仿真和实测数据的处理结果表明其有效性。